to _ro_rt. Use rtcache_getrt() to access a route cache's struct
rtentry *.
Introduce struct ifnet->if_dl that always points at the interface
identifier/link-layer address. Make code that treated the first
ifaddr on struct ifnet->if_addrlist as the interface address use
if_dl, instead.
Remove stale debugging code from net/route.c. Move the rtflush()
code into rtcache_clear() and delete rtflush(). Delete rtalloc(),
because nothing uses it any more.
Make ND6_HINT an inline, lowercase subroutine, nd6_hint.
I've done my best to convert IP Filter, the ISO stack, and the
AppleTalk stack to rtcache_getrt(). They compile, but I have not
tested them. I have given the changes to PF, GRE, IPv4 and IPv6
stacks a lot of exercise.
The mbuf chain wasn't being walked and thus fin_m was not updated to point
to the new first mbuf with data in it.
Patch from the official IPFilter repository.
alignment and nothing guarantees that IPv6 packets in mbufs are 8-byte
aligned. gcc was coalescing adjacent 32-bit compares into "ldx" on
sparc64, leading to alignment faults when processing icmp6 arriving on
gif with IPv4 outer addresses.
Fix mostly from darrenr@. Discussed extensively on port-sparc64.
set to rn_walktree.
Introduce rt_walktree(), which applies a subroutine to every route
in a particular address family. Use it instead of rn_walktree()
virtually everywhere. This helps to hide the routing table
implementation.
update in ICMP error messages. In the test case for this, the wrong
input was actually being used (it should be the headers from the previous
packet output) and therefore the expected results were also wildly wrong.
kern/36309
route_in6, struct route_iso), replacing all caches with a struct
route.
The principle benefit of this change is that all of the protocol
families can benefit from route cache-invalidation, which is
necessary for correct routing. Route-cache invalidation fixes an
ancient PR, kern/3508, at long last; it fixes various other PRs,
also.
Discussions with and ideas from Joerg Sonnenberger influenced this
work tremendously. Of course, all design oversights and bugs are
mine.
DETAILS
1 I added to each address family a pool of sockaddrs. I have
introduced routines for allocating, copying, and duplicating,
and freeing sockaddrs:
struct sockaddr *sockaddr_alloc(sa_family_t af, int flags);
struct sockaddr *sockaddr_copy(struct sockaddr *dst,
const struct sockaddr *src);
struct sockaddr *sockaddr_dup(const struct sockaddr *src, int flags);
void sockaddr_free(struct sockaddr *sa);
sockaddr_alloc() returns either a sockaddr from the pool belonging
to the specified family, or NULL if the pool is exhausted. The
returned sockaddr has the right size for that family; sa_family
and sa_len fields are initialized to the family and sockaddr
length---e.g., sa_family = AF_INET and sa_len = sizeof(struct
sockaddr_in). sockaddr_free() puts the given sockaddr back into
its family's pool.
sockaddr_dup() and sockaddr_copy() work analogously to strdup()
and strcpy(), respectively. sockaddr_copy() KASSERTs that the
family of the destination and source sockaddrs are alike.
The 'flags' argumet for sockaddr_alloc() and sockaddr_dup() is
passed directly to pool_get(9).
2 I added routines for initializing sockaddrs in each address
family, sockaddr_in_init(), sockaddr_in6_init(), sockaddr_iso_init(),
etc. They are fairly self-explanatory.
3 structs route_in6 and route_iso are no more. All protocol families
use struct route. I have changed the route cache, 'struct route',
so that it does not contain storage space for a sockaddr. Instead,
struct route points to a sockaddr coming from the pool the sockaddr
belongs to. I added a new method to struct route, rtcache_setdst(),
for setting the cache destination:
int rtcache_setdst(struct route *, const struct sockaddr *);
rtcache_setdst() returns 0 on success, or ENOMEM if no memory is
available to create the sockaddr storage.
It is now possible for rtcache_getdst() to return NULL if, say,
rtcache_setdst() failed. I check the return value for NULL
everywhere in the kernel.
4 Each routing domain (struct domain) has a list of live route
caches, dom_rtcache. rtflushall(sa_family_t af) looks up the
domain indicated by 'af', walks the domain's list of route caches
and invalidates each one.
special cases for it. This is to simplify the code to prepare it
for pullup to netbsd-4 and submitting back upstream. The change
was requested by martin@.
rtcache_init and rtcache_init_noclone lookup ro_dst and store
the result in ro_rt, taking care of the reference counting and
calling the domain specific route cache.
rtcache_free checks if a route was cashed and frees the reference.
rtcache_copy copies ro_dst of the given struct route, checking that
enough space is available and incrementing the reference count of the
cached rtentry if necessary.
rtcache_check validates that the cached route is still up. If it isn't,
it tries to look it up again. Afterwards ro_rt is either a valid again
or NULL.
rtcache_copy is used internally.
Adjust to callers of rtalloc/rtflush in the tree to check the sanity of
ro_dst first (if necessary). If it doesn't fit the expectations, free
the cache, otherwise check if the cached route is still valid. After
that combination, a single check for ro_rt == NULL is enough to decide
whether a new lookup needs to be done with a different ro_dst.
Make the route checking in gre stricter by repeating the loop check
after revalidation.
Remove some unused RADIX_MPATH code in in6_src.c. The logic is slightly
changed here to first validate the route and check RTF_GATEWAY
afterwards. This is sementically equivalent though.
etherip doesn't need sc_route_expire similiar to the gif changes from
dyoung@ earlier.
Based on the earlier patch from dyoung@, reviewed and discussed with
him.
routing caused by stale route caches (struct route). Route caches
are sprinkled throughout PCBs, the IP fast-forwarding table, and
IP tunnel interfaces (gre, gif, stf).
Stale IPv6 and ISO route caches will be treated by separate patches.
Thank you to Christoph Badura for suggesting the general approach
to invalidating route caches that I take here.
Here are the details:
Add hooks to struct domain for tracking and for invalidating each
domain's route caches: dom_rtcache, dom_rtflush, and dom_rtflushall.
Introduce helper subroutines, rtflush(ro) for invalidating a route
cache, rtflushall(family) for invalidating all route caches in a
routing domain, and rtcache(ro) for notifying the domain of a new
cached route.
Chain together all IPv4 route caches where ro_rt != NULL. Provide
in_rtcache() for adding a route to the chain. Provide in_rtflush()
and in_rtflushall() for invalidating IPv4 route caches. In
in_rtflush(), set ro_rt to NULL, and remove the route from the
chain. In in_rtflushall(), walk the chain and remove every route
cache.
In rtrequest1(), call rtflushall() to invalidate route caches when
a route is added.
In gif(4), discard the workaround for stale caches that involves
expiring them every so often.
Replace the pattern 'RTFREE(ro->ro_rt); ro->ro_rt = NULL;' with a
call to rtflush(ro).
Update ipflow_fastforward() and all other users of route caches so
that they expect a cached route, ro->ro_rt, to turn to NULL.
Take care when moving a 'struct route' to rtflush() the source and
to rtcache() the destination.
In domain initializers, use .dom_xxx tags.
KNF here and there.
- Add a few scopes to the kernel: system, network, and machdep.
- Add a few more actions/sub-actions (requests), and start using them as
opposed to the KAUTH_GENERIC_ISSUSER place-holders.
- Introduce a basic set of listeners that implement our "traditional"
security model, called "bsd44". This is the default (and only) model we
have at the moment.
- Update all relevant documentation.
- Add some code and docs to help folks who want to actually use this stuff:
* There's a sample overlay model, sitting on-top of "bsd44", for
fast experimenting with tweaking just a subset of an existing model.
This is pretty cool because it's *really* straightforward to do stuff
you had to use ugly hacks for until now...
* And of course, documentation describing how to do the above for quick
reference, including code samples.
All of these changes were tested for regressions using a Python-based
testsuite that will be (I hope) available soon via pkgsrc. Information
about the tests, and how to write new ones, can be found on:
http://kauth.linbsd.org/kauthwiki
NOTE FOR DEVELOPERS: *PLEASE* don't add any code that does any of the
following:
- Uses a KAUTH_GENERIC_ISSUSER kauth(9) request,
- Checks 'securelevel' directly,
- Checks a uid/gid directly.
(or if you feel you have to, contact me first)
This is still work in progress; It's far from being done, but now it'll
be a lot easier.
Relevant mailing list threads:
http://mail-index.netbsd.org/tech-security/2006/01/25/0011.htmlhttp://mail-index.netbsd.org/tech-security/2006/03/24/0001.htmlhttp://mail-index.netbsd.org/tech-security/2006/04/18/0000.htmlhttp://mail-index.netbsd.org/tech-security/2006/05/15/0000.htmlhttp://mail-index.netbsd.org/tech-security/2006/08/01/0000.htmlhttp://mail-index.netbsd.org/tech-security/2006/08/25/0000.html
Many thanks to YAMAMOTO Takashi, Matt Thomas, and Christos Zoulas for help
stablizing kauth(9).
Full credit for the regression tests, making sure these changes didn't break
anything, goes to Matt Fleming and Jaime Fournier.
Happy birthday Randi! :)
dyoung