and non-const types, and the kernel uses both const and non-const
PMF qualifiers and device suspensors, so change the pmf_qual_t and
device_suspensor_t typedefs from "pointers to const" to non-pointer,
non-const types.
#if NBPFILTER is no longer required in the client. This change
doesn't yet add support for loading bpf as a module, since drivers
can register before bpf is attached. However, callers of bpf can
now be modularized.
Dynamically loadable bpf could probably be done fairly easily with
coordination from the stub driver and the real driver by registering
attachments in the stub before the real driver is loaded and doing
a handoff. ... and I'm not going to ponder the depths of unload
here.
Tested with i386/MONOLITHIC, modified MONOLITHIC without bpf and rump.
illegal. I examined all places where lbolt is referenced to make
sure there were pointer aliases of it passed to tsleep, but put a
KASSERT in m/ltsleep() just to be sure.
- Addresses the issue described in PR/38828.
- Some simplification in threading and sleepq subsystems.
- Eliminates pmap_collect() and, as a side note, allows pmap optimisations.
- Eliminates XS_CTL_DATA_ONSTACK in scsipi code.
- Avoids few scans on LWP list and thus potentially long holds of proc_lock.
- Cuts ~1.5k lines of code. Reduces amd64 kernel size by ~4k.
- Removes __SWAP_BROKEN cases.
Tested on x86, mips, acorn32 (thanks <mpumford>) and partly tested on
acorn26 (thanks to <bjh21>).
Discussed on <tech-kern>, reviewed by <ad>.
invoke the common routine for both scsi and atapi tapes.
2. Replace a numeric constant with some sizeof's when calculating the
size of the mode_select command buffer, clear the entire buffer, and
KASSERT to ensure the page_0_size loaded from quirk table is valid.
3. Add a quirk for my Seagate Travan-40 tape drive.
As discussed on tech-kern@
Addresses my PR kern/34832
the end of sdattach() to the end of sd_get_parms(). The code at
the bottom of sd_get_parms() was only used for optical drives or
in the case where the drive geometry couldn't be retrived for some
reason, to create a fake geometry. The case for setting up the
real geometry was handled above that code.
sdattach(). This allows DIOCGDISKINFO to do the right thing even when
the media has changed. Note that drvctl -p will only DTRT if disk has
been opened since the most recent media chenged.
partutil.c::getdiskinfo to use it to get disk geometry info.
Use DIOCGWEDGEINFO ioctl to get information about partition size, if disk
driver doesn't support it use old DIOCGDINFO. This patch adds support for
wedge like devices(lvm logical volumes, ZFS zvol partitions) to newfs and
other tools.
No objections on tech-userlevel@.
side-effect of registering them, config_detach(9) cleared DVF_ACTIVE
before it called wddetach() or sddetach(). Even though sd(4)'s
detachment may have subsequently failed with EBUSY, we could not
begin new disk I/O on sd(4) because the device had been deactivated.
By analogy to sdstrategy(), test device_is_active() in wdstrategy()
and if it is false set b_errno to EIO instead of initiating new
disk I/O.
XXX We should decline more politely to start new I/O, since
XXX !device_is_active() may mean simply that the device is suspended.
XXX I suppose that EIO is safe as long as system suspension is
XXX all-or-nothing.
device will remain in a wait-for-more-stuff-to-be-written state delaying other
SCSI calls, esp. some read-size or read-layout calls, until its told there is
no more comming.
To fix this, on last close explicitly flush the caches releasing the device
from this mode and allowing other SCSI commands to reach it.
This fixes PR 40528
There are still about 1600 left, but they have ',' or /* ... */
in the actual variable definitions - which my awk script doesn't handle.
There are also many that need () -> (void).
(The script does handle misordered arguments.)
partitions on optical media like CD/DVD/BD but also on all other media if
there is no NetBSD disklabel or MBR label.
Also fix cd's readdisklabel arguments so the ioctl's arrive at the right
device (!) and update its default label to make more sense.
we can't use it here. Rssurect ATACH_TH_RUN, backing out
src/sys/dev/ata/ata.c 1.101
src/sys/dev/ata/ata_wdc.c 1.90
src/sys/dev/ata/atavar.h 1.77
src/sys/dev/ic/wdc.c 1.255
src/sys/dev/scsipi/atapi_wdc.c 1.108
Should fix kern/39927 and kern/39725.
When a link-layer address changes (e.g., ifconfig ex0 link
02🇩🇪ad:be:ef:02 active), send a gratuitous ARP and/or a Neighbor
Advertisement to update the network-/link-layer address bindings
on our LAN peers.
Refuse a change of ethernet address to the address 00:00:00:00:00:00
or to any multicast/broadcast address. (Thanks matt@.)
Reorder ifnet ioctl operations so that driver ioctls may inherit
the functions of their "class"---ether_ioctl(), fddi_ioctl(), et
cetera---and the class ioctls may inherit from the generic ioctl,
ifioctl_common(), but both driver- and class-ioctls may override
the generic behavior. Make network drivers share more code.
Distinguish a "factory" link-layer address from others for the
purposes of both protecting that address from deletion and computing
EUI64.
Return consistent, appropriate error codes from network drivers.
Improve readability. KNF.
*** Details ***
In if_attach(), always initialize the interface ioctl routine,
ifnet->if_ioctl, if the driver has not already initialized it.
Delete if_ioctl == NULL tests everywhere else, because it cannot
happen.
In the ioctl routines of network interfaces, inherit common ioctl
behaviors by calling either ifioctl_common() or whichever ioctl
routine is appropriate for the class of interface---e.g., ether_ioctl()
for ethernets.
Stop (ab)using SIOCSIFADDR and start to use SIOCINITIFADDR. In
the user->kernel interface, SIOCSIFADDR's argument was an ifreq,
but on the protocol->ifnet interface, SIOCSIFADDR's argument was
an ifaddr. That was confusing, and it would work against me as I
make it possible for a network interface to overload most ioctls.
On the protocol->ifnet interface, replace SIOCSIFADDR with
SIOCINITIFADDR. In ifioctl(), return EPERM if userland tries to
invoke SIOCINITIFADDR.
In ifioctl(), give the interface the first shot at handling most
interface ioctls, and give the protocol the second shot, instead
of the other way around. Finally, let compatibility code (COMPAT_OSOCK)
take a shot.
Pull device initialization out of switch statements under
SIOCINITIFADDR. For example, pull ..._init() out of any switch
statement that looks like this:
switch (...->sa_family) {
case ...:
..._init();
...
break;
...
default:
..._init();
...
break;
}
Rewrite many if-else clauses that handle all permutations of IFF_UP
and IFF_RUNNING to use a switch statement,
switch (x & (IFF_UP|IFF_RUNNING)) {
case 0:
...
break;
case IFF_RUNNING:
...
break;
case IFF_UP:
...
break;
case IFF_UP|IFF_RUNNING:
...
break;
}
unifdef lots of code containing #ifdef FreeBSD, #ifdef NetBSD, and
#ifdef SIOCSIFMTU, especially in fwip(4) and in ndis(4).
In ipw(4), remove an if_set_sadl() call that is out of place.
In nfe(4), reuse the jumbo MTU logic in ether_ioctl().
Let ethernets register a callback for setting h/w state such as
promiscuous mode and the multicast filter in accord with a change
in the if_flags: ether_set_ifflags_cb() registers a callback that
returns ENETRESET if the caller should reset the ethernet by calling
if_init(), 0 on success, != 0 on failure. Pull common code from
ex(4), gem(4), nfe(4), sip(4), tlp(4), vge(4) into ether_ioctl(),
and register if_flags callbacks for those drivers.
Return ENOTTY instead of EINVAL for inappropriate ioctls. In
zyd(4), use ENXIO instead of ENOTTY to indicate that the device is
not any longer attached.
Add to if_set_sadl() a boolean 'factory' argument that indicates
whether a link-layer address was assigned by the factory or some
other source. In a comment, recommend using the factory address
for generating an EUI64, and update in6_get_hw_ifid() to prefer a
factory address to any other link-layer address.
Add a routing message, RTM_LLINFO_UPD, that tells protocols to
update the binding of network-layer addresses to link-layer addresses.
Implement this message in IPv4 and IPv6 by sending a gratuitous
ARP or a neighbor advertisement, respectively. Generate RTM_LLINFO_UPD
messages on a change of an interface's link-layer address.
In ether_ioctl(), do not let SIOCALIFADDR set a link-layer address
that is broadcast/multicast or equal to 00:00:00:00:00:00.
Make ether_ioctl() call ifioctl_common() to handle ioctls that it
does not understand.
In gif(4), initialize if_softc and use it, instead of assuming that
the gif_softc and ifp overlap.
Let ifioctl_common() handle SIOCGIFADDR.
Sprinkle rtcache_invariants(), which checks on DIAGNOSTIC kernels
that certain invariants on a struct route are satisfied.
In agr(4), rewrite agr_ioctl_filter() to be a bit more explicit
about the ioctls that we do not allow on an agr(4) member interface.
bzero -> memset. Delete unnecessary casts to void *. Use
sockaddr_in_init() and sockaddr_in6_init(). Compare pointers with
NULL instead of "testing truth". Replace some instances of (type
*)0 with NULL. Change some K&R prototypes to ANSI C, and join
lines.
