based systems. Untested on shark, but is the right thing to do. I suspect
the original arm32 intr.h had the bug, and when the ports split we just took
the bug.
This merge changes the device switch tables from static array to
dynamically generated by config(8).
- All device switches is defined as a constant structure in device drivers.
- The new grammer ``device-major'' is introduced to ``files''.
device-major <prefix> char <num> [block <num>] [<rules>]
- All device major numbers must be listed up in port dependent majors.<arch>
by using this grammer.
- Added the new naming convention.
The name of the device switch must be <prefix>_[bc]devsw for auto-generation
of device switch tables.
- The backward compatibility of loading block/character device
switch by LKM framework is broken. This is necessary to convert
from block/character device major to device name in runtime and vice versa.
- The restriction to assign device major by LKM is completely removed.
We don't need to reserve LKM entries for dynamic loading of device switch.
- In compile time, device major numbers list is packed into the kernel and
the LKM framework will refer it to assign device major number dynamically.
to do uncached memory access during VM operations (which can be
quite expensive on some CPUs).
We currently write-back PTEs as soon as they're modified; there is
some room for optimization (to write them back in larger chunks).
For PTEs in the APTE space (i.e. PTEs for pmaps that describe another
process's address space), PTEs must also be evicted from the cache
complete (PTEs in PTE space will be evicted durint a context switch).
Change the bus_dmamap_sync() macro to test the ops argument against pre-
and post- constants. The compiler will optimize out dead code because
of the constants. Since post- operations are not needed on ARM (except
for ISA bounce buffers), this eliminate a large number of function calls
which are noops, each of which cost at least 6 cycles just in the call
and return overhead (not to mention whatever other useless work the
compiler decides to do in the callee).
counters. These counters do not exist on all CPUs, but where they
do exist, can be used for counting events such as dcache misses that
would otherwise be difficult or impossible to instrument by code
inspection or hardware simulation.
pmc(9) is meant to be a general interface. Initially, the Intel XScale
counters are the only ones supported.
A new "arm32_dma_range" structure now describes a DMA window, with
a system address base, bus address base, and length. In addition to
providing info about which memory regions are legal for DMA, the new
structure provides address translation support, as well.
As before, if a tag does not list any ranges, then all addresses are
considered valid, and no DMA address translation is performed.
This allows us to remove a large chunk of code which was duplicated and
tweaked slightly (to do the address translation) from the stock ARM
bus_dma in the XScale IOP and ARM Integrator ports.
Test compiled on all ARM platforms, test booted on Intel IQ80321 and Shark.
into platform-specific initialization code, giving platform-specific
code control over which free list a given chunk of memory gets put
onto.
Changes are essentially mechanical. Test compiled for all ARM
platforms, test booted on Intel IQ80321 and Shark.
Discussed some time ago on port-arm.
be properly used by any misc. cloning device. While here, correct
a comment to indicate that "open" is the only entry point and that
everything else is handled with fileops.
MALLOC_NOINLINE, and VNODE_OP_NOINLINE. The exceptions are when they
include another config files that already defines the options, or if
they are for an embedded board, just define a few extra options, and
do not already define PIPE_SOCKETPAIR.
Significant cleanup, here, including better PTE bit names.
* Add XScale PTE extensions (ECC enable, write-allocate cache mode).
* Mechanical changes everywhere else to update for new pte.h. While
doing this, two bugs (as a result of typos) were fixed in
arm/arm32/bus_dma.c
evbarm/integrator/int_bus_dma.c
* Don't refer to VA 0, instead refer to a new variable: vector_page
* Delete the old zero_page_*() functions, replacing them with a new
one: vector_page_setprot().
* When manipulating vector page mappings in user pmaps, only do so if
the vector page is below KERNEL_BASE (if it's above KERNEL_BASE, the
vector page is mapped by the kernel pmap).
* Add a new function, arm32_vector_init(), which takes the virtual
address of the vector page (which MUST be valid when the function
is called) and a bitmask of vectors the kernel is going to take
over, and performs all vector page initialization, including setting
the V bit in the CPU Control register ("relocate vectors to high
address"), if necessary.
In getDisplayInfo(), don't use malloc(). Instead use static storage
for the two things we'd want to allocate. getDisplayInfo() is called
before VM is bootstrapped in the console init path.
jdolecek