* Fix bug in wdc that would overflow ATAPI transfer length.
* Improve wdc probe code so that 'wdc' is probed in if present
even if there are no drives attached, and so that it works
properly even if the only device is an ATAPI slave.
* bus_space-ify.
* split the ISA attachment from the wdc driver, and remove
ISA dependencies from non-ISA files.
* claim that wd and wdc are now machine-independent (probably not
completely true, but mostly so; they at least work on arm32 and
i386).
* Various other minor fixups and cleanups, some of which were pointed
out by Kazuki Sakamoto.
now lives in dev/ic, wd now lives in dev/ata. there's now a 'ata'
interface attribute defined in conf/files, but wdc can't go there
yet because some ports still use private versions based on the old
ISA version.
the historical link? flags for media select)
XXX No pullup request for this. But if sysinst supports explicit media
XXX selection in 1.3, this should be in 1.3 as well.
clobbers my SMC. Now I can really use a generic kernel with my SMC @0x300.
This change has been tested on various machines with ne2000 and 3c509 baords.
XXX All these probes sould be reordered after the release, with invasive
XXX probes at the end.
to look specifically at the address it was provided *only*, since the
scan isn't safe (it can stomp on cards that will be probed later, like
NE2000 clones).
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
Supports changing media with ifconfig's "media" directive.
This splits the 3c503 functionality out of the ISA "ed" driver, much the
same way NE2000 support was split out.
intr_alloc_mask) into one place, comment them, and defopt them.
- Rename pcic_intr_alloc_mask to pcic_isa_intr_alloc_mask, since it's
an ISA-specific thing.
- When allocating/establishing the PCIC's interrupt (for card events),
do error checking, and pay attention to the intr_alloc_mask.
for the built-in SCSI on NEC Versa docking stations, and if a card
allocates that IRQ, it will never get interrupts. This caused the
default kernel to not work on these laptops, as IRQ 10 was often the
first free IRQ.
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Also, fix the scb freelist fencepost, like the aha/bha/uha drivers.
- at end of attach, explicitely select an existing drive. This fixes hangs
some users reported (such as the one reported in port-i386/4247).
- Some atapi cdrom drives (e.g. Nec 24x) don't enables their registers before
a controller reset is issued. The controller probe routine is changed as
follow: issue a controller reset. If fail, test atapi signature on slave.
If fail, wait 5s and retry a reset. If the second reset fail, return(0).
If the first reset succeed, test presence of a master drive:
atapi signature, and if this fail RO/RW registers test. If no master, test
atapi signature on slave. If no slave, return 0.
Instead, print a diagnostic and return. (Some drivers do this already.)
Also, normalize the diagnostic message, and fix some places where the
printfs were getting ugly.
