but which are connected to a local bus and do their own bus-mastering.
This has to be turned on via `flags 1' on the nele? device specification.
Gets one of my boxes working again with -current again.
-treat the builtin font like any other font at runtime
-for that, copy it to malloc()'d memory during attach()
-in early console initialization, if we have to consider a broken card
(VGA_CONSOLE_ATI_BROKEN_FONTSEL), copy the builtin font to another
location in font ram; the attach() code will do the rest
put the "quirk" code into effect again
found on many (all?) of PCI-based ATI graphics cards. It is fully optional
and can be enabled by adding `options VGA_CONSOLE_ATI_BROKEN_FONTSEL'
to config file.
- Temporarily remove `quirk' mechanism. Similar code already exists
in pci_quirks.c.
make the number of available font slots variable,
set up a "quirk" mechanism to tell the generic vga code about crippled
VGA adapters which ignore the "fontsel" TS register,
initiate the quirk table with an ATI chip which happened to be on a board
I tested with.
Afaik quite a number of ATI chips suffers from the "loaded fonts don't
work" problem - these should be added.
Bad side effect of my change: The builtin font will be kicked out
always if a VGA_CONSOLE_SCREENTYPE is specified which needs a loaded
font. In early console initialization, we don't know much about the
graphics card, so we have to assume the worst (ie ATI:-).
into a strange failure mode if we do it with disabled interrupt. When
(re-)enabling interrupts reset transmitter and receiver and clear any
pending state.
Make the ISA probe actually (silently) fail if no card is found.
XXX - need to aquire the SBUS variant of this card some day or have
Jaromir find an MCA one.
and move them in their proper places.
Move the BRI registry from layer 2 (duh!) to layer 4, so active cards
(which don't have layer 3 or layer 2 in their driver). Remove all remaining
hard coded controller and driver types. Remove any arbitrary hard coded
limits, at least those that show up in the internal API.
This fixes PR 15950.
indicating an unhandled "command". ERESTART is -1, which can lead to
confusion. ERESTART has been moved to -3 and EPASSTHROUGH has been
placed at -4. No ioctl code should now return -1 anywhere. The
ioctl() system call is now properly restartable.
the center position (128), so as to be compatible with other drivers.
The equalizer is enhancement only, and the values < 128 don't take
any effect.
Yeah, this causes spec change....
For equalization.treble and equalization.bass, the relation between
old and new value is
new_value = (old_value / 2) + 128.
(Note this does not apply to equalization.surround.)
2. Support ++ and -- of mixerctl(1) for stepping volume variables.
3. Fix problem where the chip is not powered up
when the mic input is unmuted.
configuration of devices logically attached to the ISA bus:
* Change the isa_attach_args to have arrays of io, mem, irq, drq
resources.
* Add a "pnpnames" and a linked list of "pnpcompatnames" to the
isa_attach_args. If either of these members are non-NULL,
direct configuration of the bus is being performed. Add an
ISA_DIRECT_CONFIG() macro to test for this.
* Drivers are not allowed to modify the isa_attach_args unless
direct configuration is not being performed and the probe fucntion
is returning success.
* Adapt device drivers -- currently, all driver probe routines return
"no match" if ISA_DIRECT_CONFIG() evaluates to true.
using one word as both attribute and device doesn't work well,
radio.c is pulled in even with no such device in the configuration,
and the kernel doesn't link due to missing "radio_cd".
So call the attribute "radiodev" to avoid confusion.
