a boot string for firmware that can do this, such as the SPARC and
the sun3 models. It is currently silently ignored on all other
hardware now, however. The MD function "boot()" has been changed to
also take a char *.
allocation calls in the event the caller does not wish to utilize those
features of extent map allocation.
Suggested by Matthew Green <mrg@eterna.com.au>
mapping code. (instead of using a "slot" and multiplying by 4 and adding the
pin number later to get the IRQ, just use base IRQ value and add the pin
number.)
comment immediately preceding it: We have to take the most significant
"numbits" from the returned value "ph", and the rest from our addr. The
addition used previously introduced a carry which was causing great
difficulty in determining the correct PA of the framebuffer VA passed in
by the booter.
values, i.e. 0xfffffffe and 0xffffffff respectively. The changed
definitions were incorrect, according to the PCI Local Bus Specification
(Revision 2.0). Further rationale and a workaround for the broken
devices that instigated the change provided in a message to
current-users@netbsd.org, dated Mon, 05 Aug 1996 22:06:58 -0400,
message ID 16773.839297218@ux2.sp.cs.cmu.edu>.
occupy a slot. This is necessary so that GRFIOCMAP can find the correct
physical address of the framebuffer. Fixes P550, some LC models, and
perhaps the PB520.
a serial console and the PRAM read/write code happens to use the ADB ROM
vectors, we will have problems because the ADB hasn't been initialized.
For now, the only class of machines that we will set these up on regardless
of whether we are on a serial console or not is the original II series (II,
IIx, and IIcx). Others can come later.
- In egstart(), if the Send Packet command fails, m_freem()
the mbuf chain before dequeueing another one (memory leak).
- In egintr(), return 1 if a known interrupt was processed.
Would manifest itself as spurious interrupts.
Don't manipulate the memlist passed from the kickstart rom + bootloader, as
we want it unchanged in case we boot via /dev/reload.
Instead, make z2mem_start known to pmap.c; and use int in pmap_bootstrap to
detect the right segment to correct and the amount.
XXX The transformation of z2mem from physical to virtual kernel addresses
in amiga_init.c must not be done before the pmap_bootstrap() call now!
* Fix radio error-message parsing bug: old comparison against error
prefix string off by the size of the Starmode link-level protocol field.
* Fix radio reset finite state machine, given that parsing works properly.
* Add debugging messages about reset FSM if IFF_DEBUG is set.
* Remove #ifdefs notdef around back the check that discards newlines at
the beginning of a frame. Every error message from the radio has a newline,
as the radio send error messages terminated by \r\n, not just \r like data
frames. Not dropping the \n garbles the following data frame.
* Remove unused low-level debugging routines.
* Reformat the low-level bytestuff/RLL code to match the canonical source.
* Reduce MTU to 1100 bytes; 1200 bytes can overflow the radio buffers if the
bytestuff/RLL does poorly.
* Fix radio-probe string to _not_ include a frame delimiter (\r): sending
a \r to the radio tickles a bug in the firmware, causing the radio to
smash the next frame sent after the "**\r" probe string.
* Add calls to the tty t_oproc routine to make sure the probe and reset
strings get sent to the modem promptly, rather than waiting for the next
packet.
* Add PPP-style calls to the tty start-output function; seems to
reduce latency marginally.
still to do:
* Flush output queue if resetting, since the radio is going to drop
frames on the floor anyway if it needs resetting.
* Reduce tty start-output calls.
message-in. The remaining transfer count restored when a device is
reselected needs to be saved. The saved value is needed to compute
the number of bytes transferred if another disconnect occurs. This
fixes a random read data corruption that occurs on certain disks that
may disconnect more than once in the middle of a DMA transfer.
If z2 memory is used for bounce buffers, it used to be stolen in
amiga_init.c, but would not be removed from the memory list there, but
in pmap.c the memory list would just be corrected.
a) the sizes subtracted got out of sync.
b) the memory segment to subtract from was guessed in pmap_init, and not
necessarily right. (e.g. consider a graphics board whose fraem buffer gets
mapped in by the RO at 0x200000, and a memory board which maps at 0x400000)
The new code subtracts the stolen aount of memory from the memlist parameter
given to the kernel by the loader, and pmap_init just doesn't see it anymore.
mycroft