and boot multi-user on a single-processor machine. Many of these changes
are wildly inappropriate for actual multi-processor operation, and correcting
this will be my next task.
based systems. Untested on shark, but is the right thing to do. I suspect
the original arm32 intr.h had the bug, and when the ports split we just took
the bug.
at run time. This simplifies the code and avoids problems with uninitialised
variables, and if it's good enough for pciide(4), it's good enough for me.
Also normalise the prefix for channel-specific messages.
necessary to allow the card to be detected afterwards. In theory, this
shouldn't be necessary, since we don't touch the page latch yet, but I'm not
going to argue.
This merge changes the device switch tables from static array to
dynamically generated by config(8).
- All device switches is defined as a constant structure in device drivers.
- The new grammer ``device-major'' is introduced to ``files''.
device-major <prefix> char <num> [block <num>] [<rules>]
- All device major numbers must be listed up in port dependent majors.<arch>
by using this grammer.
- Added the new naming convention.
The name of the device switch must be <prefix>_[bc]devsw for auto-generation
of device switch tables.
- The backward compatibility of loading block/character device
switch by LKM framework is broken. This is necessary to convert
from block/character device major to device name in runtime and vice versa.
- The restriction to assign device major by LKM is completely removed.
We don't need to reserve LKM entries for dynamic loading of device switch.
- In compile time, device major numbers list is packed into the kernel and
the LKM framework will refer it to assign device major number dynamically.
Seems that we assume that the dram blocks are sorted, and that the first/lowest address is also where the kernel is.
If the above is not true, then we're on a kinetic (probably should make a better way to indicate this) So search for all dram blocks < with starting addr lower than the first block and remove them.
Currently there's minimal performance gain (which is odd as the SDRAM is meant to be faster, I'm wondering if we need to prod some hidden registers to set timing information.
Note that I still get 16MB/s compared with 7MB/s on RiscStation and 93MB/s on my cats. I'm thinking that something else is seriously nasty on acorn32.
to do uncached memory access during VM operations (which can be
quite expensive on some CPUs).
We currently write-back PTEs as soon as they're modified; there is
some room for optimization (to write them back in larger chunks).
For PTEs in the APTE space (i.e. PTEs for pmaps that describe another
process's address space), PTEs must also be evicted from the cache
complete (PTEs in PTE space will be evicted durint a context switch).
counters. These counters do not exist on all CPUs, but where they
do exist, can be used for counting events such as dcache misses that
would otherwise be difficult or impossible to instrument by code
inspection or hardware simulation.
pmc(9) is meant to be a general interface. Initially, the Intel XScale
counters are the only ones supported.
SCSIPI_ADAPT_POLL_ONLY to tell the MI scsipi layer to do it for us. This,
plus G/Cing some debugging code, removes the card-specific scsi_request
wrappers.
into platform-specific initialization code, giving platform-specific
code control over which free list a given chunk of memory gets put
onto.
Changes are essentially mechanical. Test compiled for all ARM
platforms, test booted on Intel IQ80321 and Shark.
Discussed some time ago on port-arm.
be properly used by any misc. cloning device. While here, correct
a comment to indicate that "open" is the only entry point and that
everything else is handled with fileops.
MALLOC_NOINLINE, and VNODE_OP_NOINLINE. The exceptions are when they
include another config files that already defines the options, or if
they are for an embedded board, just define a few extra options, and
do not already define PIPE_SOCKETPAIR.
assigned by RISCOS Ltd (and were assigned by Acorn) to be unique across all
manufacturers. This means that associating each one with a manufacturer (and
checking the manufacturer when attaching) is bogus. Thus, we don't do that
any more.
This should have the pleasant side-effect of getting APDL IDE interfaces
working, since they're just ICS ones with a different manufacturer ID.
