LiViD DVD player. (See forthcoming mail to current-users.)
XXX NOTE: We should do something to probe capabilities, rather than allowing
these ioctls on any device.
- `flags' is now gone, replaced with `xs_control' and `xs_status'.
- Massive cleanup of the control flags. Now we explicitly say that
a job is to complete asynchronously, rather than relying on side-effects,
and use a new flag to now that device discovery is being performed.
- Do SCSI device discovery interrupt-driven.
- Take note of magazine changes, and enqueue "Element Status Changed" events
that user processes can read or select on.
- Normalize some structure names.
- Report back more status about changer elements:
* Volume tags (e.g. barcode labels on the backs of your tapes)
* External device names (for drive units in a changer)
* Last element a unit of media was moved from
* Sense information for SCSI changer elements in EXCEPT condition
* Vendor-specific data if the user requests it.
- Add support for setting volume tags.
2 times in the past
- Set up timeout per xfer instead of per interrupt. This helps with
PIO transfer (we would call timeout()/untimout() several times for a
transfer).
- If we missed an interrupt for a PIO transfer, reset and restart it
immedialy, don't try to recover and continue. If we missed an interrupt we
may have lost a read/write cycle on the IDE bus. If this happens 1) we
corrupt data and 2) we enter an interrupt loop at the end of the xfer, as
the drive has some more data to read/write, but the host thinks the xfer is
done.
This last change fix the (or at last some of the) 'lookup after lost interrupt'
some peoples have been experiencing.
Anyway, just because a drive doesn't support the LOAD (to BOT) command does
not mean that the drive doesn't support the UNLOAD command. Also note and
print errors in rewinds and unloads (and errors in writing closing filemarks
for same).
directly, call the function pointer (*if_input)(ifp, m). The input routine
expects the packet header to be at the head of the packet, and will adjust
as necessary. Privatize the layer 2 input and output routines, allowing
*_ifattach() to set them up as appropriate.
By code inspection I found 2 bugs in the ATAPI code, one may be the cause
of your problem: A counter is not reset when issuing the request_sense
command. This is c_skip, the counter used to track the offset in the data
buffer when a data tranfer needs multiple phases. The effect of this is that
the sense data transfered may be stored outside the sense buffer (sense buffer
+ some, potentially several KB, offset). This can only occur in PIO mode,
DMA is not affected.
This doesn't occur in "normal" use because when reading a data CD, either
the sense is issued for a non-data command (in which case c_skip stays to
0), or an error occured and no data has been transfered, and c_skip is still 0.
I can't see a case where a data READ/WRITE could cause a sense tranfer without
error.
The second problem is that b_resid can be set to a false value (resulting of
the sense tranfer and not the data transfer). Again this is not a problem with
usual data tranfers because both values ends up being 0 when no error occurs.
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
are called from the interrupt or timeout handler, 0 otherwise.
- use this to know if we can busy-wait for wait_for_unbusy or wait_for_ready
This fixes a bug where CDs withot the DRQ_INTR capability would not busy-wait
for the CMDOUT phase.
While I'm there change 2 delay() to DELAY() for consistency, and
garbage-collect some old code from wdcintr() which has been ifdef'd out
for some time now.
soren