with XS_CTL_ASYNC if the failed command was called with XS_CTL_ASYNC.
Add a SDF_RESTART flag to keep state, cleared in sddone().
A mounted disk can now spin down, it will propely spin up at the next access.
it to determine the boot device: mvme68k, pc532, macppc, ofppc. Those
platforms should be changed to use device_register(). In the mean time,
those ports defined __BROKEN_DK_ESTABLISH.
Remove "???" from T_IT8_1/2. They actually are pre-press devices for graphic arts as described by ASC IT8
Zeros and blanks scsipi_inquiry_data from byte 58 to byte 74 if additional_length is less than 58
statically. Since this function may called for another luns immediately,
allocating it statically doesn't make sense and may cause race condition
as pointed out by PR#9749.
to remove all xfers from the pending queue. It removes only xfers for
asynchronous transactions. So, simply loop over all pending xfers
with calling scsipi_done and wait xfers to drain. Addresses PR#9703.
if an IRQ was not detected, unless the force flag was given. Use this to
detect if the IRQ was for us (closer to shared IRQ for controllers which
don't have their own IRQ handler in pciide.c) and to poll for DMA xfer.
Also makes the timeout recovery code simpler.
- ATAPI cleanup: don't call controller-specific functions from atapiconf.c
(wdc_*), so that it's possible to attach an atapibus to something else
than a wdc/pciide (Hi Lennart :).
Overload struct scsi_adapter with struct atapi_adapter, defined
as struct scsi_adapter + atapi-specific callbacks. scsipi_link still points
to an scsi_adapter, atapi code casts it to atapi_adapter if needed.
Move atapi_softc to atapiconf.h so that it can be used by the underlying
controller code (e.g. atapi_wdc.c).
Add an atapi-specific callback *atapi_probedev(), which probe a drive
in a controller-specific way, allocate the sc_link and fills in the
ataparams if needed. It then calls atapi_probedev() (from atapiconf.c)
to do the generic initialisations and attach the device.
- While I'm there merge and centralise the state definitions in atavar.h.
It should now be possible to use a common ata/atapi routine to set the
drive's modes (will do later).
timeout()/untimeout() API:
- Clients supply callout handle storage, thus eliminating problems of
resource allocation.
- Insertion and removal of callouts is constant time, important as
this facility is used quite a lot in the kernel.
The old timeout()/untimeout() API has been removed from the kernel.
a historical leftover, and very few drivers actually look at it. But the
PCI `ncr' driver does, and if this field is not initialized to its default
value, that driver will fall over flat on its face when it attempts to get
sense data from a target.
- If UDMA 2 is failing try UDMA 1 first, it helps in some cases
- downgrade if we get an error in the first 4000 xfers, or if we get
4 errors in 4000 xfers if the first 4000 went without troubles.
While I'm there commit a local change I have since some time to get my CD
probed: issue a "blanck" IDENTIFY before the one used to detect slave ghosts,
with my drive the first IDENTIFY following a controller reset fails with an
aborted command ...
This is an attempt to allow people to change the default configuration
to try harder at 'mounting' a tape. This allows you to specify, in
seconds, the amount of time a non-control unit open will retry
(once per second) the scsipi_test_unit_ready when it tries to mount
the tape. It also turns off the over-verbose error reporting at
this time unless SCSIDEBUG is set.
The reason this is not enabled as a default is that it's a large change
of behaviour. I find it useful to 'try harder' at mounting a tape in
the tape driver, particularly when loaded via a media changer device
rather than specifying the delays in the backup program.
succeeds, note that we now are valid.
- Don't attempt to try and run initialize element status from interrupt level-
we don't really support that yet. Also, key more correctly off of ASC/ASCQ
instead of just the sense key.
- Make the practice of doing an INITIALIZE ELEMENT STATUS automatically when
we get params (from chopen time even) a policy decision that is not the
default for now- this can be a dangerous practice as well as time consuming.
It's dangerous in that you can have a hung open when all you really want
to do is do a read of parameters- and parameters, including slot status,
are perfectly fine to read even before an INITIALIZE ELEMENT STATUS is
done- all the elements whos status your read are going to be marked with
an exception- so leave it up to the application to decide how important
this is.
LiViD DVD player. (See forthcoming mail to current-users.)
XXX NOTE: We should do something to probe capabilities, rather than allowing
these ioctls on any device.
- `flags' is now gone, replaced with `xs_control' and `xs_status'.
- Massive cleanup of the control flags. Now we explicitly say that
a job is to complete asynchronously, rather than relying on side-effects,
and use a new flag to now that device discovery is being performed.
- Do SCSI device discovery interrupt-driven.
- Take note of magazine changes, and enqueue "Element Status Changed" events
that user processes can read or select on.
- Normalize some structure names.
- Report back more status about changer elements:
* Volume tags (e.g. barcode labels on the backs of your tapes)
* External device names (for drive units in a changer)
* Last element a unit of media was moved from
* Sense information for SCSI changer elements in EXCEPT condition
* Vendor-specific data if the user requests it.
- Add support for setting volume tags.
2 times in the past
- Set up timeout per xfer instead of per interrupt. This helps with
PIO transfer (we would call timeout()/untimout() several times for a
transfer).
- If we missed an interrupt for a PIO transfer, reset and restart it
immedialy, don't try to recover and continue. If we missed an interrupt we
may have lost a read/write cycle on the IDE bus. If this happens 1) we
corrupt data and 2) we enter an interrupt loop at the end of the xfer, as
the drive has some more data to read/write, but the host thinks the xfer is
done.
This last change fix the (or at last some of the) 'lookup after lost interrupt'
some peoples have been experiencing.
Anyway, just because a drive doesn't support the LOAD (to BOT) command does
not mean that the drive doesn't support the UNLOAD command. Also note and
print errors in rewinds and unloads (and errors in writing closing filemarks
for same).
directly, call the function pointer (*if_input)(ifp, m). The input routine
expects the packet header to be at the head of the packet, and will adjust
as necessary. Privatize the layer 2 input and output routines, allowing
*_ifattach() to set them up as appropriate.
By code inspection I found 2 bugs in the ATAPI code, one may be the cause
of your problem: A counter is not reset when issuing the request_sense
command. This is c_skip, the counter used to track the offset in the data
buffer when a data tranfer needs multiple phases. The effect of this is that
the sense data transfered may be stored outside the sense buffer (sense buffer
+ some, potentially several KB, offset). This can only occur in PIO mode,
DMA is not affected.
This doesn't occur in "normal" use because when reading a data CD, either
the sense is issued for a non-data command (in which case c_skip stays to
0), or an error occured and no data has been transfered, and c_skip is still 0.
I can't see a case where a data READ/WRITE could cause a sense tranfer without
error.
The second problem is that b_resid can be set to a false value (resulting of
the sense tranfer and not the data transfer). Again this is not a problem with
usual data tranfers because both values ends up being 0 when no error occurs.
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
are called from the interrupt or timeout handler, 0 otherwise.
- use this to know if we can busy-wait for wait_for_unbusy or wait_for_ready
This fixes a bug where CDs withot the DRQ_INTR capability would not busy-wait
for the CMDOUT phase.
While I'm there change 2 delay() to DELAY() for consistency, and
garbage-collect some old code from wdcintr() which has been ifdef'd out
for some time now.
command (unlock for sd and cd) if no other partitions are open, return
EBUSY otherwise. DIOCEJECT will have the old semantic if its argument is not
0. The old ioctl has been renamed to ODIOCEJECT for binary compatibility.
in the drive. restrict "opening of empty drive" to character devices only
(reading a block device returns a short read instead of ENODEV, which can lead
to confusion).
pending_xfers queue.
- When freeing a scsipi_xfer, remove it from the device's pending_xfers
queue. If the queue is empty, and SDEV_WAITDRAIN is set, wakeup
those waiting for the queue to drain.
- Implement scsipi_wait_drain(), which waits for a device's pending_xfers
queue to drain.
"device_q" TAILQ entries. The former is for use by the adapter driver,
as it sees fit. The latter is for the scsipi middle layer to track
pending xfers per device.
- Add a pending_xfers queue to scsipi_link, to track pending xfers per
device.
- Grow scsipi_link's flags to int, and add SDEV_WAITDRAIN, to indicate that
we're waiting for the pending_xfers queue to empty.
FC loops). Change the semantics of scsi_probedev so that it returns 1 if
you should continue probing at this target, else 0 for not.
Replace the blanket use of '7' with the use of the new sc_maxlun property
that is now gathered from HBAs. Allocate scsipi_link arrays based upon this.
Fix a really nasty and silly bug that has been there for a while where the
number of first level scsipi_link structures was one less than it needed
to be.
an array of fixed-sized channel_softc elements. This way IDE controllers
which more than 1 channel (pciide) can extend the channel data easily
for private needs.
To avoid the double dereference at runtime, change the argument of
wdcstart() to the channel data pointer instead of the array index.
Return XS_SENSE when the full sense info has been retrieved, or
XS_SHORTSENSE if only the sense key was available (from the error register)
Make atapi_interpret_sense() deal with this, and call scsipi_interpret_sense()
for XS_SENSE. (XXX sd_interpret_sense() and the ioctl code needs to be made
aware of XS_SHORTSENSE too ! sense hanlding for these is now less broken for
devices that support 'REQUEST SENSE')
All the ATAPI devices I have access to seems to honnor the SENSE_REQUEST
command, but I suspect some ATAPI devices will not (althouh it's mandatory).
The code should be able to deal with this, but is untested ...
scsi_base.c to scsipi_base.c. Rename the functions from scsi_verbose.c
too, and rename the file itself. Cleaup includes too (scsi_*.h should not
be #included in scsipi_*.h files, which are supposed to be
common to atapi and scsi).
in the printing of DMA mode (piix3/4 only)
others: set the debug_mask to 0, so that debug messages are turned off by
default but can be easily turned on.
Reset drive_flags to 0 for unconfigured devices, so that they are ignored
later. For configured devices, reset state to 0 after probe/attach.
Our other constants also use "ATALK".
Added many new ETHERTYPE constants to sys/net/ethertypes.h, including the
ones from libpcap and tcpdump "ethertype.h" files.
