per-packet discard of every received packet increases latency and
decrease throughput. INstead, Spin on S_COMMAND_IN_PROGESS for enough
iterations as the expected time to completion. Only do DELAY()/poll
loops (as suggested by Jason Thorpe) if spinning fails.
Take PCI as fastest case and compute worst-case estimate.
Shorten DELAY() in S_COMMAND_COMPLETE polling-loop up 10, loop-count
down. to speed up epreset() completion (m/c filter change, ifup/ipdown, etc).
* Clear the `enabled' bit in the softc so late hardware interrupts
(e.g., just after the full reset) done as part of shutdown) are dropped.
* Eliminate loops that poll forever on S_COMMAND_IN_PROGRESS to complete.
Add inline function with bounded loopcount plus small delay, to avoid
bugs in EISA hardware which never sets S_COMMAND_IN_PROGRESS.
Use for both TX_RESET/RX_RESET/GLOBAL_RESET cmds, and polling for
discard-Rx completion
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
Big-endian CPUs should use bus_space_{read,write}_multi_stream methods
to PIO packet data to NIC in 16-bit or 32-bit chunks.
Make it so.
Since we don't have stream methods on all ports yet (esp. i386), use
the bus_space_{read,write}_multi methods if the compile-time
stream-method feature-test macro is not set.
Originally from tsubai@netbsd.org, via HAYAKAWA koichi's cardbus patches.
we can identify them as cardbus chips supported by the cardbus patches.
Add entry for OPTI chipsets whose interrupts arent properly set up by
some BIOSes.
From cardbus patches<ftp://nandra.iri.co.jp/pub/NetBSD/CardBus by
HAYAKAWA Koichi <haya@tcad.ulsi.sony.co.jp>.
- Don't rely on ATA signature: some ide controllers seems to not transmit it
properly (SIMIDE on arm32 machines). Instead, when we guess a drive is here
after reset, just mark it as ATA and OLD is it's not ATAPI.
- at attach time, use IDENTIFY to eliminate ghost from the probe. If the
drive had the old flag and IDENTIFY failed, issue a WDCC_RECAL command
to detect a pre-ATA disk. If IDENTIFY succeded, remove the OLD flag,
it's obviously not a pre-ATA disk.
- add a new controller flag, WDC_CAPABILITY_PREATA, used to shorcut parts
of the probe (not necessary, but makes the probe/attach faster). This is
only set by the ISA front-end, all other controllers supported can't have
pre-ATA drives attached.
The mechanism used are more or less the same as before, they have just been
reordered. Should solve port-arm32/7324 (waiting for feedback).
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
clean bit. This is somewhat bogus as RAID 0 does not have any parity,
but is a slightly cleaner than other solutions, and makes the handling
of clean bits for RAID 0 consistent with the handling of clean bits at
other RAID levels.
mrg