1. fix possible hang in en_txlaunch(). when attempting to extend
the length of an mbuf to avoid a flush we should extend it
by cnt [which is ((need - len) % 4)] rather than 4 - cnt.
also, add an EN_DEBUG printf() when we pad/FLUSH a buffer
to help with debugging/understanding what the driver is up to.
2. use interface packet counters
3. when turning off a recv VCI we recompute the new mode. make sure
we don't include the "in service" bit in the new mode, otherwise
a VCI may appear "hung" if you turn it off while a service
interrupt is pending.
4. when shutting down a VCI that is still receiving data, don't bother
going into "drain mode" if only the hardware in service bit is
set (otherwise the VCI may get "hung" in drain mode).
as a result of this we may get "unexpected rx interrupt" messages
which are not really an error, so put this printf in EN_DEBUG.
5. be sure to zero txspeed[lcv] when enabling a VCI (start at full
speed). (hooks for setting txspeed[] are currently not in
the driver, but we are playing with it locally).
credits:
#1: Detected by: Zdenek Salvet <salvet@horn.ics.muni.cz>, fix by me.
#2: Contributed by: Zdenek Salvet <salvet@horn.ics.muni.cz>
#3,#4,#5: Detected by: Milind M. Buddhikot <milind@dworkin.wustl.edu>,
fixed by me.
2841, plus some fixes to make the patches work on the Alpha. Seems to
improve the NCR driver a lot. We probably should try to incorporate
any updates that have happened since, too.
* Add a slot in the softc, ep_pktlenshift, to indicate that
a board implements ``large packets'' (FDDI-sized frames) and
therefore implicitly shifts the argument to packet-length commands
by two bits to fit a 13-bit length in an 11-bit command argument field.
* Change the reset of station-mask filterto be independent of bus-type
(e.g.,. for 3c515)
* Replace the "2044" constant used to disable TX threshold interrupts
on 3c509-generation cards with a #define. Use 2047 instead,
since that works on the large-packet cards (Vortex, Demon, Boomerang)
and 2044 doesn't.
* Add code to epconfing to probe for large-packet support,
set the softc appropriately, and shift packet sizes in commands
by ep_pktlenshift to compensate for the implicit shift.
* Tweak the epconfig() code to avoid hanging on startup.
Set the Tx threshold to interrupt when there's space for
a maximal-sized ether frame, then do epinit() then epstop(),
instead of just the Tx and Rx reset. Required on at least a 3c595.
Tested on a 3c595, but not on 3c509-generation hardware.
(This fixes problems with the printf format fixes i checked in yesterday.
ptrdiff_t is an 'int' on the i386 but a 'long' on the alpha, so the cast
really is necessary... *sigh*)
ISA-compatible port space of PCI buslogic cards.
* Add call to bha_pci.c to disable the ISA-compatible ports of a PCI
device. The ISA-compatible ports are enabled by default, which
causes the card to be autoconfigured a second time as an ISA device,
which appears to deadlock the card.
* Change bha_cmd() to return the number of bytes it actually received
in response to a command, or -1 on error.
* Use heuristics (checking for bha-only registers, and checking the size
of the response to BHA_INQURE_EXTENDED) to bha_find, to make sure the
bha driver never matches an aha (Adaptec 1542 or compatible) device.
A single kernel should now boot on either Adaptec or BusLogic controllers,
provided we always probe for BusLogic devices before Adaptec devices,
but this has not yet been verified.
management by itself. But when it gets a start unit request, it keeps
the floppy motor running all the time. This adds code for dealing with
yet another quirk (SDEV_NOSTARTUNIT) that prevents sd.c from sending
start unit requests. A entry for the Teac FC-1 is added to the quirk
table.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
prototypes, and suppress a bogus "might be used uninitialized" warning.
It's clear from reading the logic of the function that produces the
warning that the variable will not be used uninitialized, but the
compiler just isn't smart enough, I guess. Marked XXX for future reference.
restart if we get multiple status interrupts before the softintr()
routine gets a chance to run. The fix is to determine and accumulate
status line changes at the H/W interrupt level, and then check and zero
the accumulated changes when the softint() finally runs. Many thanks
to Bill Studenmund <wrstuden@loki.stanford.edu> for finding and fixing.
dev/microcode/aic7xxx_seq.h,
dev/ic/aic7xxxreg.h:
Remove intrinsic knowledge about SDTR and WDTR messages and replace it
with a generic message system that allows the kernel driver to handle
SDTR, WDTR and any other type of extended message it chooses too. This
makes the sequencer code much simpler, makes extended message handling
debuggable since the bulk of the work is in the kernel driver, and saves
lots of instruction space.
Regen microcode header file.
dev/ic/aic7xxx.c, dev/ic/aic7xxxvar.h:
Add code to handle WDTR and SDTR negotiation in light of the changes in
the message interface to the sequencer. Don't reject targets that
negotiate async by sending an SDTR with a 0 offset. Use an sdtr message
with 0,0 to negotiate async when a target suggests a period that is too
long for us to handle. Some tape and cdrom drives don't like us doing
the message reject that we did in the past.
Fix a problem with handing the QUEUE FULL condition.
Fix a race condition (most likely the cause of the SCB paging problems) that
might allow the sequencer to get unpaused before the condition that caused
it to be paused (a SEQINT) was handled.
Race condition pointed out by Doug Ledford <dledford@dialnet.net> and
by "Dan Willis" <dan@plutotech.com>.
dev/pci/ahc_pci.c:
Add support for the 2940AU, an aic7860 based controller.
dev/pci/pcidevs.h, dev/pci/pcidevs_data.h:
Add product IDs for the 2940AU, aic7860 and aic7855.
Regen data file.
scsi/scsi_message.h:
Add MSG_EXT_SDTR_LEN and MSG_EXT_WDTR_LEN - the length of bytes in these
extended messages.
Thanks to Chuck Cranor <chuck@maria.wustl.edu> for testing these changes
out for me.
* When we are transferring in DATA (in asc_dma_in) and the target
is an async device, there is sometimes an extra byte in the FIFO.
If so, we need to drain that byte out of the fifo, but if and only
if the target is async. See also the comments in asc_dma_in()
in the related Mach mk84 asc driver (scsi_53C94_hdw.c), which
has an identical fix but applied in more restrictive conditions
than we need, with async *disk* targets, as well as async tapes.
* Add a watchdog and timeout active SCSI requests, to eliminate any
potential for deadlock due to applying the fix above on newer
silicon versions of the 53c94 which may not have the above problem.
Should use the MI scsi per-target timeout instead, when available.
cfattach code for TC SCSI option cards and ioasic 53c94 baseboard SCSI.
ascvar.h: shared softc declarations
asc_ioasic.c: ioasic front-end code.
asc_tc.c: Turbochannel option (and 5000/200 basebard) front-end code.
* ioasic_attach meeds more work to eliminate pmax_type dependency
and to verify the clocks speed passed to 53c94.
* Add prototypes for asc script entry points; should compile with
-Wstrict-prototypes -Wmissing-prototypes.
* Use tcvar.h interface. The usage of tc_syncbus() and tc_mb() may
not be quite stylistically on an Alhpa, but it apparently makes no
difference on the eerly-generation Alpha CPUs in TC Alphas.
if the version is <= SCSI-2. This should help some older SCSI
devices that previously needed the "NOLUNS" quirk. While this is
not strictly necessary on SCSI-2 devices, the spec allows it,
so we set it for SCSI-2 devices "just in case". See section 7.2.2 of
Draft X3T9.2 Rev 10L for details.
multi-channel driver), or to SCSI_CHANNEL_ONLY_ONE if a
single-channel driver.
(2) use scsiprint() rather than a locally-defined autoconfig print
function, and kill any locally-defined print function.
(2) in scsibusmatch, match channel as appropriate.
(3) add a scsiprint() function, to do the "scsibus at..."
and channel (if not SCSI_CHANNEL_ONLY_ONE) printing,
i.e. the common functionality that all SCSI drivers currently
should be doing.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
Fix so that resource wait queueing works.
Changed all functions to take a pointer to uba_softc instead of unit
number, except for ubareset(). This must be done later.
chuck