pci_dev_funcorder() that have the following signatures:
int pci_bus_devorder(pci_chipset_tag_t pc, int bus, char list[32]);
int pci_dev_funcorder(pci_chipset_tag_t pc, int bus, int device, char list[8]);
they control the order of PCI bus probe at the device and function level,
by filling in a value from 0 to 31 for pci_bus_devorder() or 0 to 7 for
pci_dev_funcorder, with a value of -1 to signify no more entries.
when device properties arrive, these will be replaced with some facility
based on properties (design/implementation unknown currently.)
pci_config_dump variable to 1. otherwise, it gets set to 0. If
that's set, when configuring PCI devices spew the very verbose
configuration space header dump that was previously "#if 0"'d.
If you use this option, or patch the variable to 1, it's strongly
encouraged that you have used the MSGBUFSIZE option to enlarge the
kernel message buffer.
of functions on a given device. Also, clean up the #if 0'd
major-debugging-spew code so that it's all one piece, so that
it's a bit prettier, and so that it prints out quirk information.
lots of data, e.g. ~18k on a PCI system with few add-in devices; use
with MSGBUFSIZE=...). Useful to have here so that people who want as
much data about the PCI configuration in a machine can get it without
having to craft their own code. Also, clean up a few of the other
#if 0'd printfs.
ID) when determining if the Vendor ID is invalid. The spec says that
Vendor ID of 0xffff is invalid, so, it doesn't _matter_ what the product
ID is in that case. Treat Vendor ID 0 as invalid because we always have.
arguments, so that a device can tell if its memory and I/O spaces are
enabled. The flags are cleared, depending on the contents of devices CSR
registers, in the machine-independent PCI bus code.
that their child busses can be attached after the PCI bus
autoconfiguration for their parent bus is done.
This works because:
(1) there can be at most one ISA/EISA bridge per PCI bus, and
(2) any ISA/EISA bridges must be attached to primary PCI
busses (i.e. bus zero).
That boils down to: there can only be one of these outstanding
at a time, it is cleared when configuring PCI bus 0 before any
subdevices have been found, and it is run after all subdevices
of PCI bus 0 have been found.
This (or something like it) is needed because there are some (legacy)
PCI devices which can show up as ISA/EISA devices as well (the prime
example of which are VGA controllers). If you attach ISA from a
PCI-ISA/EISA bridge, and the bridge is seen before the video board is,
the board can show up as an ISA device, and that can (bogusly)
complicate the PCI device's attach code, or make the PCI device not be
properly attached at all.
This could be done with machine-dependent code, but as more ports
add support for PCI (and PCI-ISA/EISA bridges) more will need it.
The i386 port could (perhaps should) be converted to use it as well.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
(soon to be documented on mailing lists; eventually in section 9 manual
pages), most importantly:
(1) support interrupt pin swizzling on non-i386 systems with
PCI-PCI bridges (per PPB spec; done, but meaningless, on i386).
(2) provide pci_{io,mem}_find(), to determine what I/O or memory
space is described by a given PCI configuration space
mapping register.
(3) provide pci_intr_map(), pci_intr_string(), and
pci_intr_{,dis}establish() to manipulate and print info about
PCI interrupts.
(4) make pci functions take as an argument a machine-dependent
cookie, to allow more flexibility in implementation.
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
pcibus and pci.
(2) remove the #ifdef i386 from pci.c, and provide a machine-dependent
hook (pci_md_attach_hook()) to do any machine-dependent attachment
gunk, e.g. on the i386 printing out the configuration mode (if bus 0)
(3) don't pass max device number for a given bus in, use
PCI_MAX_DEVICE_NUMBER, which can be defined on a per-machine basis.
(defaults to 32. on i386, it's 32 if pci conf mode == 1, 16 if 2.)
(pci_attach_subdev()). remove pciattach() function and the pcicd cfdriver
struct, the former because thre are a lot of attachment actions which really
are machine-dependent (perhaps even "most"), and the latter because now that
both pcimatch() and pciattach() are machine-dependent it's bad style to
declare them here and it gains nothing.
