from sppp_attach.
When destroying the interface, call sppp_detach for proper cleanup.
This avoids a crash from the slow timeout handler for no longer existing
interfaces (spotted by Rémi Zara).
does not use software interrupts; remove these bridge netisr
hooks left over from a previous incarnation of the bridge code.
Noted by Andrew Brown <atatat@atatdot.net>.
The type of ALIGN() is vary on architecture and casting pointer to u_int
is incorrect for MI code.
Since the code is to make sure aligned access to IP header and requires
bcopy if the test fails. So the performance implication is not necessary
and we can use ALIGNED_POINTER() here.
pointed out by nathanw.
XXX: FH chanset should be calculated by FH hop pattern, but BayStack 650 AP
always specify chanset to fixed value 1. The previous code try to this
hack into awi driver, but it is insufficient because the chanset value
in awi driver may change while scan and it may be different from the
value in receiving beacon/probe-response. So we save encoded FH chanset
into channel in 802.11 common bss information for now.
if_ieee80211subr.c, which can be shared between any IEEE 802.11
drivers.
However, most of current working IEEE 802.11b wireless LAN cards
have rich firmware and we cannot have a control to management frames
for such cards.
IBSS creation is now supported for the awi driver.
complete for some reason, we defer it for a bit and then try again. This
gets ping down to 0% packet loss.
Of course, ping _should_ have been at 0% packet loss anyway, and that's the
next thing to deal with.
Add capabilities bits that indicate an interface can only perform
in-bound TCPv4 or UDPv4 checksums. There is at least one Gig-E chip
for which this is true (Level One LXT-1001), and this is also the
case for the Intel i82559 10/100 Ethernet chips.
worked out by observing RISC iX's behaviour, so it may be technically
wrong. The only implementations of IP-over-Econet for which I've got
sources don't support broadcasts.
Tested using broadcast ping from RISC iX to NetBSD, and using rwhod.
Use m_copydata() to preserve the Econet header, so we don't depend on
notionally-unused areas of an mbuf remaining untouched.
Check that ARP-over-Econet requests are exactly eight bytes long.
Use m_pullup() before trusting mtod().
Between them, these make reception of unicast ARP responses work properly.
protocols, and lacking any timeouts, but it basically works, doing four-way
handshakes in both directions and incoming Machine Peek operations.
Oh, and Econet is Acorn's ancient, proprietary 500kbit/s networking
technology.
on gateway change, copy rmx_mtu from gateway only under the following condition:
- current MTU is not locked
- current MTU was discovered via PMTUD
XXX if gateway has MTU == 0, current MTU is set to 0 and we are going to
rediscover PMTU again. is it good or bad?
the bit mask of open NCPs got out of sync.
Defer the (potential) closing of LCP after a NCP went down until after
the state machines got updated.
This fixes PR kern/11161.
follows BSD/OS practice and ucd-snmp code (FreeBSD does it for specific
interfaces only).
was: if_lastchange get updated on every packet transmission/receipt.
now: if_lastchange get updated when IFF_UP is changed.
the broadcast case as well) to see if they came from us, and drop
them if they did.
This fixed IPv6 DAD on non-simplex interfaces, e.g. the Seeq 8003
found on my SGI Indy.
network interfaces. This works by pre-computing the pseudo-header
checksum and caching it, delaying the actual checksum to ip_output()
if the hardware cannot perform the sum for us. In-bound checksums
can either be fully-checked by hardware, or summed up for final
verification by software. This method was modeled after how this
is done in FreeBSD, although the code is significantly different in
most places.
We don't delay checksums for IPv6/TCP, but we do take advantage of the
cached pseudo-header checksum.
Note: hardware-assisted checksumming defaults to "off". It is
enabled with ifconfig(8). See the manual page for details.
Implement hardware-assisted checksumming on the DP83820 Gigabit Ethernet,
3c90xB/3c90xC 10/100 Ethernet, and Alteon Tigon/Tigon2 Gigabit Ethernet.
based on the existing net/if_spppsubr.c stuff.
While there are completely userland (bpf based) implementations available,
those have a vastly larger per packet overhead thus causing major CPU
overhead and higher latency. On an i386 base router, running a 486DX at 50MHz
my line (768kBit/s downstream) was limited to something (varying) between 10
and 20 kByte/s effective download rate. With this implementation I get full
bandwidth (~85kByte/s).
This is client side only. Arguably the right way to add full PPPoE support
(including server side) would be a variation of the ppp line discipline and
appropriate modifications to pppd. I promise every help I can give to anyone
doing that - but I needed this realy fast. Besids, on low memory NAT boxes
with typically a single PPPoE connection, this implementation is more
lightweight than a pppd based one, which nicely fits my needs.
In this mode, the PPP packets start with the protocol identifier and don't
have any explicit framing (which may be added by the lower level driver).
Make input/output statistics a little bit more correct by adding a hardware
driver adjustable framing length for each packet (instead of the constant
value "3" used before).
While there, bump authentication name length from 32 to 48 (I have a
connection where I need more than 32). XXX - this should not be artificialy
limited at all.
tree, which allows a packet with Ethernet headers already present to
run through the ALTQ packet classifier. This is needed in order to
suport ALTQ on VLAN and bridge devices.
adds rt_parent to link parent from child (like NRL did, ours do refcnt
rt_refcnt properly).
bsdi rt_walkbranch would speedup the processing, but since the code will not
be visited too frequently, the current code (with rt_walktree) should be okay.
let static routes overwrite cloned routes, as cloned routes can come back again
if necessary. behavior same as freebsd/bsdi, code partially from bsdi42.
(NRL rt->rt_parent was not added)
should fix PR 11916 and maybe some other PRs with ARP behavior.
recompilation of usr.sbin/route6d is suggested.
