This is very adhoc work for IETF meeting.
- Since it seems that 'an' and 'wi' have similar hardware, low level
functions should be shared.
- There are PCI/ISA cards of Aironet but not supported yet.
- The wiconfig interface is changed so that wiconfig cannot be used.
- 'ancontrol' of FreeBSD is not ported.
- Only infrastructure mode is tested.
- WEP is not supported.
Though I only have an Aironet card, Cisco card should be expected to work.
Current status:
Only OHCI chip is supported (fwohci).
ping (IPv4) works with Sony's implementation (SmartConnect) on Win98.
sometimes works but not stable.
Not implemented yet:
IRM (Isochronous Resource Manager) functionality.
Link layer fragmentation.
Topology map.
More to do:
clean ups
MCAP
charactor device part
dhcp
There is no entry in GENERIC config file yet.
Follow sys/dev/ieee1394/IMPLEMENTATION to enable if_fw.
when running at splserial(). This is a temporary measure (until
there's a MP-safe interrupt handling structure); until then, it should
be used when MULTIPROCESSOR and IPL_SERIAL > IPL_SCHED.
that required to support NFSv2 mounts. Not finished yet, but already
provides some 44k of saving in code size on arm26. More savings, and some
documentation, are still to come.
and a front-end driver for the Ether3. Only semantic change is to remove
ea_claimirq() and ea_releaseirq() on the grounds that the seem too spurious
to warrant a callback to the front-end.
as used on later arm26 system (A5000, A4, A3010, A3020, A4000).
What we have got:
...
upc0 at iobus0 base 0x010000: config state bb 87 1c 00 00
fdc at upc0 offset 0x3f4 not configured
wdc0 at upc0 offset 0x1f0
lpt0 at upc0 offset 0x278
com0 at upc0 offset 0x3f8: ns8250 or ns16450, no fifo
...
What we haven't got:
- FDC support (found, but not configured).
- Clearing lpt interrupts on arm26 systems (needs help from IOEB).
- A upc(4) manual page.
- More than minimal testing (my A3020s don't have root devices).
- A proper probe routine (arm26 can't use one anyway).
break character with the supplied one. This is useful for cases where
break is hard to generate, or you are connected to a PC that "sends"
breaks when power cycled. For this mode in com, interpret break char
in the polling section, which allows entry into the debugger before
the tty is opened. Only supported in the com driver currently.
arc4 implementation by Kalle Kaukonen has been added.
define "wlan" in files.
XXX: only awi depends on wlan for now.
Allow authentication for adhoc (IBSS) mode.
Disable adhoc mode without bssid (mediaopt adhoc,flag0) for FH radio.
FH cannot work without synchronization by beacons.
Align IP header for ethernet encapsulation (IFF_FLAG0) mode.
Print available access points for IFF_DEBUG.
such as the LM78 and VT82C686A (and eventually ACPI). Multiple
sensor devices can be hooked registered with `sysmon', and eventually
sysmon will also handle hardware (and software) watchdog timers.
Convert the `lm' and `viaenv' drivers to the new interface.
- use latest source address selection code - in6_src.c.
- correct frag header insertion.
- deep copy ip6 header portion in ip6_mloopback to avoid overwrite.
- do not bark when we forward packet to loopback.
- some cosmetics.
This work is based on code written by Scott D. Telford, the IBM
Token Ring card attachment was written by Gregory McGarry.
XXX this is still very experimental and development version; use at your
XXX own risk
thorpej