2) Modify pnpbus attachment code to record the chipid of the device if it
has one.
3) Change the clock probes to use the chipid, rather than relying on
potentially untrustworthy subtype and interface.
4) Add decoding of memory ranges to the RESIDUAL_DUMP code.
5) Add a we@pnpbus device to allow netbooting and root device detection
from an IBM we ethernet. (it will only work if your firmware detects it)
6) Because I moved the pnpbus probe to occur prior to pci and isa, it
screwed up the root device detection and firmware path building code.
Completely rewrite the fw-path detection code to deal with this.
and INSTALL_SMALL. Since floppy images have to fit on one floppy, we
have to really cut down on the drivers on that image, but people
netbooting don't have that problem, so they deserve a more featured
kernel to install with. (namely one with raid support and more ethernet
drivers)
residual with the pnpbus probes, than it is to do it with raw isa probes,
so I've replaced the isa mkclock and mcclock code with a pnpbus attachment.
While writing the mkclock code, I realized that on motorola prep machines
the mkclock uses the same port range as the nvram part. (it's actually
the same chip/part). This was causing the nvram not to work on those
machines. Now the nvram code will recognize this, and wire up the
mkclock as well. The mkclock probe is just a stub probe used to
pre-detect the fact that this is one of those machines.
ones and those for specific machines of developers. PR 32304.
OK'ed by rpaulo.
N.B. stf is a cloning device, so it still must be enabled by
"ifconfig stf0 create".
1) Add the NVRAM device. This device allows us to speak with the nvram on
prep-based machines and read/write to it. Also add a simple IOCTL
interface for speaking with the nvram from userland. This hasn't been
tested yet, but eventually I plan to support it with the sparc eeprom
command.
2) Change the root device detection to use the nvram device to attempt to
guess the boot device. Most machines should now correctly guess thier
boot device, though I expect a few devices to still not work quite right yet.
3) change the default IRQ to level rather than edge in the pnpbus if the
flags are invalid or empty. (based on output from a PowerStack E1)
4) correctly handle older machines in pnpbus that have FixedIOPorts
rather than variable ones.
Still have much to do.
1) create new pnpbus psuedo bus. This is a bus layer that reads the PNP
tree from the residual data and allows attachment of devices with the
information given therein. Based loosely on i386/pnpbios.
2) Delete obio bus, as with the pnp bus we no longer need it.
3) Create a number of functions that gather the information needed to set
up the machine from the residual data, rather than hardcoding it in.
4) Create a quirk table for machines that are bizzare enough that the
residual information is not sufficient. (such as the 6015)
5) Using the data gathering routines and the quirk table, delete struct
platform completely from the architecture. Prep is now almost completely
dynamic in figuring out the machine it is running on and setting things
up properly.
6) Add a wdc_pnpbus driver which attaches the wdc controller found on
some 7248's and the 6015. This replaces the now-defunct wdc_obio.
7) delete all the mot_* and ibm_* files, and replace them with a single
ibm_machdep.c which only contains the quirk functions for the 6015 and
the 6050.
8) Modify GENERIC to work with all this stuff.
Changes:
Added a pci-EISA bridge device and associated glue to the prep port.
Adapted from i386.
Change pci_intr_fixup_*() to pass the pin argument on all platforms.
Make PCI_NETBSD_CONFIGURE leave the MPIC alone. We map it separately.
7024 kernel was also succ. tested on an IBM 7043, so no regression there.
was developed as part of Google's Summer of Code 2005 program. This
change adds the kernel code, the mount_tmpfs utility, a regression test
suite and does all other related changes to integrate these.
The file-system is still *experimental*. Therefore, it is disabled by
default in all kernels. However, as typically done, a commented-out
entry is added in them to ease its setup.
Note that I haven't commited the required mountd(8) changes to be able
to export tmpfs file-systems because NFS support is still very unstable
and because, before enabling it, I'd like to do some other changes.
OK'ed by my project mentor, William Studenmund (wrstuden@).
(still commented out)
- Add (also commented out) options BUFQ_PRIOCSCAN.
Suggested by perry and soda on tech-kern.
Please refer options(4) for details for these options.
