Also, if the so-called DMA operation is a write and ends without target-
complete set, count the data in the FIFO as residual and add that to the
amount in the counters. Hauke Fath reports that this passes early testing
on his Quantum Viking.
if it is 64k. TCL and TCM will be set properly if we just leave it alone.
Not only that, the ncr53c9x driver issues TRPAD or TRANS based on this
value. We do not want TRPAD in this case!
an ugly bit where we record the value of a2 while handling a "nofault" bus
error in locore.s in order to know how far the transaction got before a
disconnect (see esp.c comments for more details on this).
Also get rid of a loop (and delay()!) in the interrupt routine--hinted at
and researched by Chas Williams <chas@cmf.nrl.navy.mil>.
only signal handler array sharable between threads
move other random signal stuff from struct proc to struct sigctx
This addresses kern/10981 by Matthew Orgass.
implement pseudo-DMA transfers with the SCSI controller. This caused our
match to fail when we couldn't map the entire DAFB register/control space
for our own use. Instead, we map only (about) what we will need in two
separate regions.
As a consequence we no longer do Turbo SCSI configuration here; indeed, it
may have caused us trouble later on if we actually changed the values
stored in those registers in the esp driver.
* move all exec-type specific information from struct emul to execsw[] and
provide single struct emul per emulation
* elf:
- kern/exec_elf32.c:probe_funcs[] is gone, execsw[] how has one entry
per emulation and contains pointer to respective probe function
- interp is allocated via MALLOC() rather than on stack
- elf_args structure is allocated via MALLOC() rather than malloc()
* ecoff: the per-emulation hooks moved from alpha and mips specific code
to OSF1 and Ultrix compat code as appropriate, execsw[] has one entry per
emulation supporting ecoff with appropriate probe function
* the makecmds/probe functions don't set emulation, pointer to emulation is
part of appropriate execsw[] entry
* constify couple of structures
rather than assigning to the whole field, set or clear individual flags,
which implies that the B_BUSY and B_INVAL flags will remain set.
this allows us to make the assertion in brelse() that B_BUSY is set,
which is the purpose of all this.
in fact on this planet -- generate a SIGILL for user-mode A-line traps.
The core of this change is taken verbatim from PR 10511, submitted by
Christian Bauer.
with a call to macfb_clear().
[The purpose of macfb_init() is almost exclusively to initialize the
raster console blitter. We really, really do not want to do this unless
we are actually initializing the console device, else we'll give rcons
the attributes of the last-seen fb device. These will not necessarily
correspond to the attributes of the actual console device!]
pseudo-device pty 2 # pseudo-terminals (Sysinst needs two)
(Some installers may not be using sysinst, in which case this just reduces
the number of ptys from 16 that are not used to 2 that are not used)
For i386 conf files, no change other than comments.
addresses, it makes sense to print the actual address of the device rather
than the original address. The latter is useful to distinguish the type
of device only, so we maintain that data internally (as we always have).
This closes PR 10557 from Dave Huang.
based on it working already for macppc.
Also add commented out:
#options VNODE_OP_NOINLINE # Don't inline vnode op calls
#options NFS_V2_ONLY # Exclude NFS3 and NQNFS code
as suggestions for additional savings
respond in the allotted time if they're told to TALK immediately after
completing a LISTEN command. Experimentation with adb_op_sync() yielded
consistent results when the timeout was increased from the documented
6900 usec to 8000 usec, so we'll make that change here.
(Accurate and complete documentation of the hardware sure would help...)
