(e.g., the 1240). Include the new 1080/1240 NVRAM layout reading code. Some
moderately significant mailbox changes were necessary also to accomodate a
second channel.
has the console input device. The USB keyboard driver uses this to
attach the first USB keyboard instance as the console keyboard.
Unfortunately, this must still be deferred to autoconfiguration time,
but there's not much we can do about that right now.
By code inspection I found 2 bugs in the ATAPI code, one may be the cause
of your problem: A counter is not reset when issuing the request_sense
command. This is c_skip, the counter used to track the offset in the data
buffer when a data tranfer needs multiple phases. The effect of this is that
the sense data transfered may be stored outside the sense buffer (sense buffer
+ some, potentially several KB, offset). This can only occur in PIO mode,
DMA is not affected.
This doesn't occur in "normal" use because when reading a data CD, either
the sense is issued for a non-data command (in which case c_skip stays to
0), or an error occured and no data has been transfered, and c_skip is still 0.
I can't see a case where a data READ/WRITE could cause a sense tranfer without
error.
The second problem is that b_resid can be set to a false value (resulting of
the sense tranfer and not the data transfer). Again this is not a problem with
usual data tranfers because both values ends up being 0 when no error occurs.
return 0 instead of EINVAL. In this case, there will only be one media
type, and the upper-level if_media code will ensure that the user is setting
to that type.
In other words, don't require the front-end to provide the no-op.
- Initialize more of the Bt463's registers, instead of leaving them
in undefined states. Notably, the window type table is set up
with 8-plane pseudocolor and 24-plane truecolor modes.
- Bus-space-ify, mostly. Could use some more cleanup, but not until
the rest of the tga stuff is converted, too.
- Do the TGA/RAMDAC communication dance more carefully.
- Explain a lot more of what's going on in comments.
Reorganise the driver some what.
Rename tr_reset() to the more appropriate tr_stop().
Create a common tropic reset routine and use it in the frontends.
Move the code in tr_config() which is only used in the card attachment
routines into a new tr_attach() function.
Take adapter off the ring through tr_shutdown() in a shutdown hook.
This simplifies the bus-specific frontend.
Verify EEPROM checksum, extract card rev-level, test capabilities
word, then test high-order config bits to verify card is in PnP mode,
and skip if so.
* resid in pcscp_dma_intr() should also be set in the data out phase.
* Don't set up DMA in the transfer pad operations.
* Change URL of the PDF technical manual to the index page.
* include <machine/bswap.h> on big endian machines.
Fixes timeouts writing large blocks to tapes. From Izumi Tsutsui,
PR 7252.
per-packet discard of every received packet increases latency and
decrease throughput. INstead, Spin on S_COMMAND_IN_PROGESS for enough
iterations as the expected time to completion. Only do DELAY()/poll
loops (as suggested by Jason Thorpe) if spinning fails.
Take PCI as fastest case and compute worst-case estimate.
Shorten DELAY() in S_COMMAND_COMPLETE polling-loop up 10, loop-count
down. to speed up epreset() completion (m/c filter change, ifup/ipdown, etc).
* Clear the `enabled' bit in the softc so late hardware interrupts
(e.g., just after the full reset) done as part of shutdown) are dropped.
* Eliminate loops that poll forever on S_COMMAND_IN_PROGRESS to complete.
Add inline function with bounded loopcount plus small delay, to avoid
bugs in EISA hardware which never sets S_COMMAND_IN_PROGRESS.
Use for both TX_RESET/RX_RESET/GLOBAL_RESET cmds, and polling for
discard-Rx completion
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
Big-endian CPUs should use bus_space_{read,write}_multi_stream methods
to PIO packet data to NIC in 16-bit or 32-bit chunks.
Make it so.
Since we don't have stream methods on all ports yet (esp. i386), use
the bus_space_{read,write}_multi methods if the compile-time
stream-method feature-test macro is not set.
Originally from tsubai@netbsd.org, via HAYAKAWA koichi's cardbus patches.
we can identify them as cardbus chips supported by the cardbus patches.
Add entry for OPTI chipsets whose interrupts arent properly set up by
some BIOSes.
From cardbus patches<ftp://nandra.iri.co.jp/pub/NetBSD/CardBus by
HAYAKAWA Koichi <haya@tcad.ulsi.sony.co.jp>.
- Don't rely on ATA signature: some ide controllers seems to not transmit it
properly (SIMIDE on arm32 machines). Instead, when we guess a drive is here
after reset, just mark it as ATA and OLD is it's not ATAPI.
- at attach time, use IDENTIFY to eliminate ghost from the probe. If the
drive had the old flag and IDENTIFY failed, issue a WDCC_RECAL command
to detect a pre-ATA disk. If IDENTIFY succeded, remove the OLD flag,
it's obviously not a pre-ATA disk.
- add a new controller flag, WDC_CAPABILITY_PREATA, used to shorcut parts
of the probe (not necessary, but makes the probe/attach faster). This is
only set by the ISA front-end, all other controllers supported can't have
pre-ATA drives attached.
The mechanism used are more or less the same as before, they have just been
reordered. Should solve port-arm32/7324 (waiting for feedback).
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
clean bit. This is somewhat bogus as RAID 0 does not have any parity,
but is a slightly cleaner than other solutions, and makes the handling
of clean bits for RAID 0 consistent with the handling of clean bits at
other RAID levels.
board versions with no BIOS. Separate mailbox interrupts from
IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not
after you clear it (potential race condition). Clear out older broken
BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup
if already in LVD mode. Note usage of presumptive 1040C revision. For
all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state
as unknown as well as marking the need to do a getpdb on targets- after
a LIP for certain the f/w has to do PRLI/PLOGI for all targets again
and marking f/w state as unknown gives us a fighting chance to (start
to) hold up for that to complete.
that will SBusify an isp header or the lun/target portions of a request IOCB-
and have these only valid iff __sparc__ (no non-sparc SBus machine that *I*
know about).