Newer boards (e.g., Vortex) take time to reset, and wedge on some machines.
Polling on S_COMMAND_IN_PROGRESS would be better, but that doesn't
work with xx_RESET commands on 3c509s.
CONFIG_CNTRL bits by making the "conn" argument to epconfig()
a u_int, not a u_int16_t, and by defining 100mbit media
bits in the upper 16 bits.
A redesigned interface that fixes this properly is in the pipeline.
comments in pr port-i386/2358: "if_ep/3C590 no longer working"
* Only call Vortex media-config code on PCI-attached devices, until
we know if it works on ISA and EISA large-packet devices also.
* Fix typo in printf of MAC address
rather than unknown.
* Look for 100mbit interfaces, and for any present, set corresponding
bits in `conn' argument to epconfig(). epconfig() will now print
100Mbit media by name.
look for 100mbit Xcvrs, print their names, add to ep_connectors.
* Print 10baseT as 10baseT, since media name (utp) is no longer a unique
transceiver type.
* Redo FIFO memory size printing, also show Tx/Rx split (xxx isa 3c509?).
* Print MAC address on a separate line, with 100Mbit media and fifo-ram
info it no longer fits on the same line as media types.
* Comment the fact that the "connection" media-selection code just doesn't
grok 100Mbit media.
* add code to look for 3c59x/3c90x media-select and autoconfig bits, though
we don't yet dynamically probe media when the autoconfig bit is set
(see previous bullet).
* XXX the whole connector/media code should be redone, perhaps a' la
the BSDI ifmedia design.
For now, we really only need 8 bits of media type.
* Add bogus definitions for 100mbit transcievers, to be set in the
"conn" argument to ep_config(). Should really use the same bits
as in EP_W0_CONFIG_CTRL bits, but I don't know what bits the 3c515
&c use for 100mbit media.
* Define bitflags for 100Mbit transceiver options in ep_connectors.
* Add definitions of powerup/powerdown commands. for interfaces with
power management. Should send a powerup after APM resume?
* Add definition of fragment-busmaster (vortex) START_DMA command.
* Add definition of PCI configuration-space media-present bits.
(really just EP_W3_RESET_OPTIONS remapped into pci config space.)
* Add comments describing what the #define's above are used for.
For now, we really only need 8 bits of media type.
* Add bogus definitions for 100mbit transcievers, to be set in the
"conn" argument to ep_config(). Should really use the same bits
as in EP_W0_CONFIG_CTRL bits, but I don't know what bits the 3c515
&c use for 100mbit media.
* Define bitflags for 100Mbit transceiver options in ep_connectors.
* Add definitions of powerup/powerdown commands. for interfaces with
power management. Should send a powerup after APM resume?
* Add definition of fragment-busmaster (vortex) START_DMA command.
* Add definition of PCI configuration-space media-present bits.
(really just EP_W3_RESET_OPTIONS remapped into pci config space.)
* Add comments describing what the #define's above are used for.
bit from the extended setup inquiry and key off it to:
- Force synchronous negotiation on targs > 7.
- Read additional information returned by wide cards on inquire setup.
- Read sync period on targs > 7.
- Display sync period/offset on targs > 7.
- Set scsi_link.max_target to 15.
cvs: ----------------------------------------------------------------------
host adapter drivers, indicating the highest SCSI target they can
address. Use this value to dynamically allocate data structures, rather
than hard-coding 8 targets.
These changes allow targets > 7 to be addressed on wide SCSI busses.
Fixes PRs #1674 and #2892.
Add newline to `Interface disabled' printf and clean up formatting.
Change packet read/write code to align all reads and writes into
memory to an appropriate boundary for the I/O size. This also fixes
a bug where the trailing unaligned bytes (1-3 of them) would be
put in an additional mbuf even if there was enough space for them
in the one we were currently filling.
This has been tested on a 3c905 in an Alpha (32-bit I/O, alignment
required), a 3c905 in an i386 (32-bit I/O, alignment not required)
and a 3c509 in an i386 (16-bit I/O, alignment not required). It
should be tested on a 3c509 in an Alpha with an ISA bus, if somone
can manage to get the two items together.
There are still some bugs in the driver relating to initialisation;
on my Alpha with a 3c905 you need to do an `ifconfig ep0 down;
ifconfig ep0 up' after the initial ifconfig to make it start working.
Apparently there are also some problems with a 3c579 in an i386,
although a 3c905 in an i386 works just fine.
