Commit Graph

26 Commits

Author SHA1 Message Date
leo b66dd55f59 Backout endian changes here (per discussion with Justin) and move them to
aic7xxx.c
1998-04-16 07:07:37 +00:00
leo dd709a7f89 Make it possible to interface to big-endian cpu's. 1998-03-11 20:57:03 +00:00
mjacob 5cafda5b3c Update 2100 F/W to 1.10 level. Also remove some older 2100 f/w versions.
This version of the 1.10 f/w is initiator only (not initiator/target).
1998-01-28 06:09:02 +00:00
perry fff05a68ab RCSID Police. 1998-01-05 07:31:05 +00:00
mjacob fd208bedb2 Rev up to 1.09 FC f/w, but keep 1.07 around- 1.09 is a little strange. 1997-12-05 19:42:32 +00:00
mjacob d90bb02e10 oops on a comment- it is 1.07 FW, not 1.05 1997-12-03 00:45:05 +00:00
mjacob fee73b1391 Roll to 1.7 F/W level. 1997-11-17 05:07:02 +00:00
mjacob 20d01ea842 Updated f/w from Qlogic. 1997-11-02 22:10:57 +00:00
lukem 3e8e744696 getopt returns -1 not EOF 1997-11-01 06:49:14 +00:00
mjacob 38ea6714c9 New microcode release (1.02) from qlogic for the 2100. 1997-09-19 14:15:54 +00:00
mjacob 695bb7c37e Addition of PCI Qlogic ISP2100 (Fibre Channel) support meant a slight
change in f/w layout.
1997-08-16 00:30:37 +00:00
cgd e36a5ca4de change microcode array definitions from "unsigned short" to the more
correct u_int16_t, and remove bogus casts that the old definition
required.
1997-03-13 04:07:44 +00:00
mycroft 919efaeb60 Make the microcode table const. 1997-03-13 03:33:03 +00:00
cgd cf26d31ad2 NetBSD RCS ID tweaks, a few comment block tweaks. Also, make copyright
notices consistent (per Matt Jacob).
1997-03-12 21:06:41 +00:00
cgd 099e30a322 ISP 10x0 driver from Matthew Jacob of NASA Ames Research Center.
(March 12, 1997 version).
1997-03-12 20:44:50 +00:00
gibbs b9c06e6fa3 dev/microcode/aic7xxx/aic7xxx.seq,
dev/microcode/aic7xxx_seq.h,
dev/ic/aic7xxxreg.h:
  Remove intrinsic knowledge about SDTR and WDTR messages and replace it
  with a generic message system that allows the kernel driver to handle
  SDTR, WDTR and any other type of extended message it chooses too.  This
  makes the sequencer code much simpler, makes extended message handling
  debuggable since the bulk of the work is in the kernel driver, and saves
  lots of instruction space.

  Regen microcode header file.

dev/ic/aic7xxx.c, dev/ic/aic7xxxvar.h:
  Add code to handle WDTR and SDTR negotiation in light of the changes in
  the message interface to the sequencer.  Don't reject targets that
  negotiate async by sending an SDTR with a 0 offset.  Use an sdtr message
  with 0,0 to negotiate async when a target suggests a period that is too
  long for us to handle.  Some tape and cdrom drives don't like us doing
  the message reject that we did in the past.

  Fix a problem with handing the QUEUE FULL condition.

  Fix a race condition (most likely the cause of the SCB paging problems) that
  might allow the sequencer to get unpaused before the condition that caused
  it to be paused (a SEQINT) was handled.

  Race condition pointed out by Doug Ledford <dledford@dialnet.net> and
  by "Dan Willis" <dan@plutotech.com>.

dev/pci/ahc_pci.c:
  Add support for the 2940AU, an aic7860 based controller.

dev/pci/pcidevs.h, dev/pci/pcidevs_data.h:
  Add product IDs for the 2940AU, aic7860 and aic7855.

  Regen data file.

scsi/scsi_message.h:
  Add MSG_EXT_SDTR_LEN and MSG_EXT_WDTR_LEN - the length of bytes in these
  extended messages.

Thanks to Chuck Cranor <chuck@maria.wustl.edu> for testing these changes
out for me.
1996-10-08 03:04:02 +00:00
mycroft 035c4e9b65 Compile the sequencer statically. 1996-08-10 08:36:48 +00:00
mycroft ed82d062fe Use HOSTED_C_C when building the assembler. 1996-08-10 08:24:59 +00:00
explorer 73cb5a96f8 aic, not aix... Stupid typo 1996-07-13 06:20:11 +00:00
explorer 00f9b22eb8 Remove aic7xxx_seq.h on clean, build it on depend. This closes pr 2608,
2441, and part of 2600.  2436 is left open to remind me that Chris's
comments are probably correct.  This file should be built statically and
committed to the tree, not built on a per-kernel basis.
1996-07-13 06:19:34 +00:00
explorer c62a6661a1 Updates to aic7xxx driver ; from pr port-i386/2600 1996-07-10 22:50:44 +00:00
thorpej a318461042 RCS Id police. 1996-05-20 00:48:43 +00:00
mycroft 19b0b9502f New version, with changes from Justin Gibbs and Noriyuki Soda. 1996-05-16 03:44:13 +00:00
christos 3a77c25f3e Add prototypes. 1996-04-29 19:30:50 +00:00
christos 3f3082e5f5 Add a clean target to clean the assembler binary 1996-04-29 19:30:19 +00:00
mycroft b216bead49 Add an Adaptec 2940 driver, by John Aycock and Justin Gibbs, ported to NetBSD by Stefan
Grefen, with several bug fixes by me.
1995-10-09 09:49:30 +00:00