Verify EEPROM checksum, extract card rev-level, test capabilities
word, then test high-order config bits to verify card is in PnP mode,
and skip if so.
* resid in pcscp_dma_intr() should also be set in the data out phase.
* Don't set up DMA in the transfer pad operations.
* Change URL of the PDF technical manual to the index page.
* include <machine/bswap.h> on big endian machines.
Fixes timeouts writing large blocks to tapes. From Izumi Tsutsui,
PR 7252.
per-packet discard of every received packet increases latency and
decrease throughput. INstead, Spin on S_COMMAND_IN_PROGESS for enough
iterations as the expected time to completion. Only do DELAY()/poll
loops (as suggested by Jason Thorpe) if spinning fails.
Take PCI as fastest case and compute worst-case estimate.
Shorten DELAY() in S_COMMAND_COMPLETE polling-loop up 10, loop-count
down. to speed up epreset() completion (m/c filter change, ifup/ipdown, etc).
* Clear the `enabled' bit in the softc so late hardware interrupts
(e.g., just after the full reset) done as part of shutdown) are dropped.
* Eliminate loops that poll forever on S_COMMAND_IN_PROGRESS to complete.
Add inline function with bounded loopcount plus small delay, to avoid
bugs in EISA hardware which never sets S_COMMAND_IN_PROGRESS.
Use for both TX_RESET/RX_RESET/GLOBAL_RESET cmds, and polling for
discard-Rx completion
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
Big-endian CPUs should use bus_space_{read,write}_multi_stream methods
to PIO packet data to NIC in 16-bit or 32-bit chunks.
Make it so.
Since we don't have stream methods on all ports yet (esp. i386), use
the bus_space_{read,write}_multi methods if the compile-time
stream-method feature-test macro is not set.
Originally from tsubai@netbsd.org, via HAYAKAWA koichi's cardbus patches.
we can identify them as cardbus chips supported by the cardbus patches.
Add entry for OPTI chipsets whose interrupts arent properly set up by
some BIOSes.
From cardbus patches<ftp://nandra.iri.co.jp/pub/NetBSD/CardBus by
HAYAKAWA Koichi <haya@tcad.ulsi.sony.co.jp>.
- Don't rely on ATA signature: some ide controllers seems to not transmit it
properly (SIMIDE on arm32 machines). Instead, when we guess a drive is here
after reset, just mark it as ATA and OLD is it's not ATAPI.
- at attach time, use IDENTIFY to eliminate ghost from the probe. If the
drive had the old flag and IDENTIFY failed, issue a WDCC_RECAL command
to detect a pre-ATA disk. If IDENTIFY succeded, remove the OLD flag,
it's obviously not a pre-ATA disk.
- add a new controller flag, WDC_CAPABILITY_PREATA, used to shorcut parts
of the probe (not necessary, but makes the probe/attach faster). This is
only set by the ISA front-end, all other controllers supported can't have
pre-ATA drives attached.
The mechanism used are more or less the same as before, they have just been
reordered. Should solve port-arm32/7324 (waiting for feedback).
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
clean bit. This is somewhat bogus as RAID 0 does not have any parity,
but is a slightly cleaner than other solutions, and makes the handling
of clean bits for RAID 0 consistent with the handling of clean bits at
other RAID levels.
board versions with no BIOS. Separate mailbox interrupts from
IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not
after you clear it (potential race condition). Clear out older broken
BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup
if already in LVD mode. Note usage of presumptive 1040C revision. For
all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state
as unknown as well as marking the need to do a getpdb on targets- after
a LIP for certain the f/w has to do PRLI/PLOGI for all targets again
and marking f/w state as unknown gives us a fighting chance to (start
to) hold up for that to complete.
that will SBusify an isp header or the lun/target portions of a request IOCB-
and have these only valid iff __sparc__ (no non-sparc SBus machine that *I*
know about).
was deasserted and we wanted to change parameters to -crtscts
This effectively stalled the transmitter since with TS_BUSY set
we only change parameters during the Tx interrupt handler.
are called from the interrupt or timeout handler, 0 otherwise.
- use this to know if we can busy-wait for wait_for_unbusy or wait_for_ready
This fixes a bug where CDs withot the DRQ_INTR capability would not busy-wait
for the CMDOUT phase.
While I'm there change 2 delay() to DELAY() for consistency, and
garbage-collect some old code from wdcintr() which has been ifdef'd out
for some time now.
TULIP_BUSMODE_BIGENDIAN does bswap packet buffers also, so we should use
TULIP_BUSMODE_DESC_BIGENDIAN on big-endian machines. (PR 7027)
XXX 21040 doesn't have this bit, but supporting only 21041+ is better than
nothing.
DELAY(1)'s. This should fix interrupt driven lpt driver hang and
reboot problems for the group of users who have experienced them, and
shouldn't hurt anyone else.
* The fact that IIR_NOPEND was not set on entry does *not* mean that no
transmission was in progress. Besides, we don't want to throw away receive
interrupts either.
* In the !clearirq case, we didn't splx().
1. don't clear the irq unless it was clear before transmitting
2. also do various bus_space_barrier() ops
Stops console from freezing when kprintf interrupts tty driver output.
IDENTIFY said so: it doesn't help for the drive this was supposed helping,
and seems to break another device.
In interrupt routine, don't return 0 if we are polling: this should fix the
"panic: wdc_exec_command: polled command not done" some people reported
(kern/7269).
and ignore the error. Scanset 2 should be the default after reset, so
this allows some broken keyboards to work. (Reset is needed because at
least 1 keyboard locks up if the "set scanset" is attempted.)
