- for ipv4, defer decision to ip layer as h/w checksum offloading does
so that it can check the actual interface the packet is going to.
- for ipv6, disable it.
(maybe will be revisited when it implements h/w checksum offloading.)
ok'ed by Jason Thorpe.
net.local.stream.pcblist
net.local.dgram.pcblist
net.inet.tcp.pcblist
net.inet.udp.pcblist
net.inet.raw.pcblist
net.inet6.tcp6.pcblist
net.inet6.udp6.pcblist
net.inet6.raw6.pcblist
which allow retrieval of the pcbs in use for those protocols. The
struct involved is 32/64 bit clean and incorporates parts of struct
inpcb, struct unpcb, a bit of struct tcpcb, and two socket addresses.
Connect over tcp on the loopback is broken:
4729 amq 0.000007 CALL connect(4,0x804f2a0,0x1c)
4729 amq 75.007420 RET connect -1 errno 60 Connection timed out
(this can never have worked)
now I can use a "bge" gigabit interface with hw checksumming
ttcp-t: 2147483648 bytes in 18.31 real seconds = 114527.11 KB/sec +++
woow!
Gone are the old kern_sysctl(), cpu_sysctl(), hw_sysctl(),
vfs_sysctl(), etc, routines, along with sysctl_int() et al. Now all
nodes are registered with the tree, and nodes can be added (or
removed) easily, and I/O to and from the tree is handled generically.
Since the nodes are registered with the tree, the mapping from name to
number (and back again) can now be discovered, instead of having to be
hard coded. Adding new nodes to the tree is likewise much simpler --
the new infrastructure handles almost all the work for simple types,
and just about anything else can be done with a small helper function.
All existing nodes are where they were before (numerically speaking),
so all existing consumers of sysctl information should notice no
difference.
PS - I'm sorry, but there's a distinct lack of documentation at the
moment. I'm working on sysctl(3/8/9) right now, and I promise to
watch out for buses.
close sockets on address changes, which was deemed to be a bad idea and was
summarily removed, so there is no point in wasting effort on maintaining it
any more.
configured with ``options FAST_IPSEC''. Kernels with KAME IPsec or
with no IPsec should work as before.
All calls to ip_output() now always pass an additional compulsory
argument: the inpcb associated with the packet being sent,
or 0 if no inpcb is available.
Fast-ipsec tested with ICMP or UDP over ESP. TCP doesn't work, yet.
be inserted into ktrace records. The general change has been to replace
"struct proc *" with "struct lwp *" in various function prototypes, pass
the lwp through and use l_proc to get the process pointer when needed.
Bump the kernel rev up to 1.6V
manner as the ifaddr hash table. By doing this, the mkludge code can go
away. At the same time, keep track of what pcbs are using what ifaddr and
when an address is deleted from an interface, notify/abort all sockets
that have that address as a source. Switch IGMP and multicasts to use pools
for allocation. Fix a number of potential problems in the igmp code where
allocation failures could cause a trap/panic.
Do a little mbuf rework while here. Change all uses of MGET*(*, M_WAIT, *)
to m_get*(M_WAIT, *). These are not performance critical and making them
call m_get saves considerable space. Add m_clget analogue of MCLGET and
make corresponding change for M_WAIT uses.
Modify netinet, gem, fxp, tulip, nfs to support MBUFTRACE.
Begin to change netstat to use sysctl.
optimization made last year. should solve PR 17867 and 10195.
IP_HDRINCL behavior of raw ip socket is kept unchanged. we may want to
provide IP_HDRINCL variant that does not swap endian.
as necessary:
* Implement a new mbuf utility routine, m_copyup(), is is like
m_pullup(), except that it always prepends and copies, rather
than only doing so if the desired length is larger than m->m_len.
m_copyup() also allows an offset into the destination mbuf, which
allows space for packet headers, in the forwarding case.
* Add *_HDR_ALIGNED_P() macros for IP, IPv6, ICMP, and IGMP. These
macros expand to 1 if __NO_STRICT_ALIGNMENT is defined, so that
architectures which do not have strict alignment constraints don't
pay for the test or visit the new align-if-needed path.
* Use the new macros to check if a header needs to be aligned, or to
assert that it already is, as appropriate.
Note: This code is still somewhat experimental. However, the new
code path won't be visited if individual device drivers continue
to guarantee that packets are delivered to layer 3 already properly
aligned (which are rules that are already in use).
