charge/discharge rates was incorrect - the value printed is actually
in A, W, Ah, or Wh, not in mA, mW, mAh, or mWh (assuming as we must
that the period is interpreted as a decimal point, not a thousands
separator).
So make bcmp.c define bcmp and memcmp.
This should (?) fix the atari build.
(I've now no idea why the previous change defined memcpy for the alpha build.)
FreeBSD ahd driver:
Fix a race condition in the flushing of commands that
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
FreeBSD ahd driver:
aic79xx.h:
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
FreeBSD ahd driver:
Correct a typo in a comment.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
FreeBSD ahd driver:
aic79xx.h:
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
