argument. So check so is non-NULL before doing the pointer-chasing
dance to find the PCB. (Unless and until we rework fast-ipsec and
KAME, to pass a struct in_pcbhdr * instead of the struct socket *).
reported by Shiva Shenoy
while we're here, fix another problem when the same interface address is
assigned to !IFF_MULTICAST and IFF_MULTICAST interface. if ip_multicast_if()
returns the first one, join/leave will fail, which is not an desired effect.
configured with ``options FAST_IPSEC''. Kernels with KAME IPsec or
with no IPsec should work as before.
All calls to ip_output() now always pass an additional compulsory
argument: the inpcb associated with the packet being sent,
or 0 if no inpcb is available.
Fast-ipsec tested with ICMP or UDP over ESP. TCP doesn't work, yet.
Do a little mbuf rework while here. Change all uses of MGET*(*, M_WAIT, *)
to m_get*(M_WAIT, *). These are not performance critical and making them
call m_get saves considerable space. Add m_clget analogue of MCLGET and
make corresponding change for M_WAIT uses.
Modify netinet, gem, fxp, tulip, nfs to support MBUFTRACE.
Begin to change netstat to use sysctl.
"In rare cases when there is no room for ip options ip_insertoptions()
can fail and corrupt a header length. Initialize len and check what
ip_insertoptions() returns."
optimization made last year. should solve PR 17867 and 10195.
IP_HDRINCL behavior of raw ip socket is kept unchanged. we may want to
provide IP_HDRINCL variant that does not swap endian.
- the destination is IPv4 multicast or 255.255.255.255, and
- outgoing interface is specified via socket option
this simplifies operation of routed
(no longer reqiure 224.0.0.0/4 to be set up)
outgoing interface (ia == NULL after IFP_TO_IA).
historic behavior (up to revision 1.43) was to use 0.0.0.0 as source address,
but it seems like a mistake according to RFC1112/1122.
Add capabilities bits that indicate an interface can only perform
in-bound TCPv4 or UDPv4 checksums. There is at least one Gig-E chip
for which this is true (Level One LXT-1001), and this is also the
case for the Intel i82559 10/100 Ethernet chips.
network interfaces. This works by pre-computing the pseudo-header
checksum and caching it, delaying the actual checksum to ip_output()
if the hardware cannot perform the sum for us. In-bound checksums
can either be fully-checked by hardware, or summed up for final
verification by software. This method was modeled after how this
is done in FreeBSD, although the code is significantly different in
most places.
We don't delay checksums for IPv6/TCP, but we do take advantage of the
cached pseudo-header checksum.
Note: hardware-assisted checksumming defaults to "off". It is
enabled with ifconfig(8). See the manual page for details.
Implement hardware-assisted checksumming on the DP83820 Gigabit Ethernet,
3c90xB/3c90xC 10/100 Ethernet, and Alteon Tigon/Tigon2 Gigabit Ethernet.
- let ipfilter look at wire-format packet only (not the decapsulated ones),
so that VPN setting can work with NAT/ipfilter settings.
sync with kame.
TODO: use header history for stricter inbound validation
by interface index. if the interface address specified is in 0.0.0.0/8
it will be considered as interface index in network byteorder.
getsockopt(IP_MULTICAST_IF) preserves old behavior if
setsockopt(IP_MULTICAST_IF) was done with interface address, and
returns interface index if setsockopt(IP_MULTICAST_IF) was done with
interface index (again using the form in 0.0.0.0/8).
Suggested by Dave Thaler, based on RIPv2 MIB spec (RFC1724 section 3.3).
http://mail-index.netbsd.org/tech-net/2001/01/13/0003.html
- All packets are passed to PFIL_HOOKS as they come off the wire, i.e.
fields in protocol headers in network order, etc.
- Allow for multiple hooks to be registered, using a "key" and a "dlt".
The "dlt" is a BPF data link type, indicating what type of header is
present.
- INET and INET6 register with key == AF_INET or AF_INET6, and
dlt == DLT_RAW.
- PFIL_HOOKS now take an argument for the filter hook, and mbuf **,
an ifnet *, and a direction (PFIL_IN or PFIL_OUT), thus making them
less IP (really, IP Filter) centric.
Maintain compatibility with IP Filter by adding wrapper functions for
IP Filter.
ip_output(). This flag, if set, causes ip_output() to set
DF in the IP header if the MTU in the route is not locked.
This allows a bunch of redundant code, which I was never
really all that happy about adding in the first place, to
be eliminated.
Inspired by a similar change made by provos@openbsd.org when
he integrated NetBSD's Path MTU Discovery code into OpenBSD.
correct timestamp option validation (len and ptr upper/lower bound
based on RFC791).
fill "pointer" field for parameter problem in timestamp option processing.
jonathan