Clean up the name space here a bit.
Add a `busname' element to struct ofprobe (now struct ofbus_attach_args), and
check against it.
Nuke `ofroot'.
Rename the `openfirm' attribute to `ofbus'.
in pci/if_tl.c, call config_found() with a print function, instead of
printing ourself a message in if_tl.c if no miibus was found. The print
function is in mii/mii.c (mii_adapter_print()) so that it can be used by any
adapter (idea from the scsi system).
it simple, and allocate one for each transmit and receive descriptor.
In addition to being simpler and faster, this fixes a serious memory leak
in the transmit path.
fixes a condition where stale data can be left in the status byte, causing
user programs that interpret it to fail.
Fixes kern/4964 from Chris Jones <cjones@honors.montana.edu>.
- In the console getc routine, block until a character becomes ready
(no, really, we mean it). This routine should _never_ time out.
- In the console putc routine, if the UART has trouble, do NOT proceed
to print a diagnostic message, which would recursively invoke the
console putc routine ad nauseum.
tested on any other platform other than i386. Use of bus_dma(9) can be
turned by defining TULIP_BUS_DMA_NOTX and TULIP_BUS_DMA_NORX. These allow
one to determine if the problem is in the transmit or receive path.
A problem reported by mycroft is also fixed.
UVM was written by chuck cranor <chuck@maria.wustl.edu>, with some
minor portions derived from the old Mach code. i provided some help
getting swap and paging working, and other bug fixes/ideas. chuck
silvers <chuq@chuq.com> also provided some other fixes.
this is the rest of the MI portion changes.
this will be KNF'd shortly. :-)
the "stream" busification functions.
In the architecture as the BeBox(CPU is big endian, have ISA bus),
These methods would be used where "raw" data needs to {read,write,set}
unchanged.
Add #ifndef __BUS_SPACE_NEED_STREAM_METHODS (define that on NetBSD/bebox),
if not define __BUS_SPACE_NEED_STREAM_METHODS,
define "stream" busification functions to normal busification functions.
The old ofbprint() wasn't particularly good (it forced the root node
to have a 'name' property, which apparently violates the OFW spec), and
the new one (though it normally prints more useful information) has
nothing useful to say about the root node. It's not clear to me that
'ofroot' should exist at all.
This is useful in the case where an attachment's probe routine
verifies that there is indeed hardware present but something goes
"wrong" in the attach causing the device to be unusable. (Without
keeping track of this, in that case incorrect ports could be
accessed or uninitted pointers could be deferenced on open or at
other times.)
an initiator/target nexus and thus mark the correct queue (if any) a
command is on.
* If a disconnected command times out, just leave it on the nexus queue
and do nothing (for now). I need yet to decide on the strategy to
follow in this case. Note: we used to move the command to the `ready'
queue and then do nothing, which is worse.
which checks for the presence of any of a set of caller-provided
strings in a node's "compatible" property (the _right_ way to
determine driver compatibility).
in the Shark source tree for a while, but Jason's recent commit to
dp8390.c spurred me to check it in here.)
XXX Assumes the device is an ethernet, but then so does other code in
this driver.
the target still is in MSG OUT phase. We still send a message (a NO_OP)
in this case and the chip will remove ATN at the appropriate time.
Using the RSTATN command here induces a "illegal command" in some
chip revisions.
This situation only occurs if the target rejects a previous (multi-byte)
message early (by switching to MESSAGE IN and sending a MESSAGE REJECT)
before the chip has completed the entire MSG OUT transfer. ATN will
remain asserted, and the target returns to MESSAGE OUT phase.
* Account for the events above when reporting "DMA not completed"
diagnostic messages.
* Stream-line the selection code a bit, and make the DMA setup code
more like the MSG OUT & DATA XFER setup.
- Fall back on i/o space if mem space isn't available.
- Card reports mem space as prefetchable, but mapping the card into dense
space fails in nasty ways on the Alpha. Force mapping into sparse
space by clearing the BUS_SPACE_MAP_CACHEABLE bit (XXX!).
fix 'cd' driver's NCD_SCSI bogosity (was using testing wrong macro!)
clean up in various ways:
* make common atapi_mode_{sense,select}() functions.
* put ATAPI data structures in more sensible headers, split up by
device type.
* include headers a bit more carefully.
* pass flags to attachment-specific cd functions, and use them.
* get rid of SCSI bits in scsipi_base.h's scsipi_make_xs(), move
them into the correct place in scsi_base.c.
* fix minor typo in struct name in scsipiconf.h (which was apparently
never used except in a #define later in the same file).
* use __attribute__ to force 4-byte alignment for xs command store,
so that architectures trying to bus_space_write_multi_N() (where
N > 1) that data to a controller won't lose.
* clean up a few comments in typos, and make a few #defines easier to
understand/maintain.
* rename cd_link.h to cdvar.h (via repository copy). This is exactly
what a 'var' file is supposed to be.
* Fix bug in wdc that would overflow ATAPI transfer length.
* Improve wdc probe code so that 'wdc' is probed in if present
even if there are no drives attached, and so that it works
properly even if the only device is an ATAPI slave.
* bus_space-ify.
* split the ISA attachment from the wdc driver, and remove
ISA dependencies from non-ISA files.
* claim that wd and wdc are now machine-independent (probably not
completely true, but mostly so; they at least work on arm32 and
i386).
* Various other minor fixups and cleanups, some of which were pointed
out by Kazuki Sakamoto.
now lives in dev/ic, wd now lives in dev/ata. there's now a 'ata'
interface attribute defined in conf/files, but wdc can't go there
yet because some ports still use private versions based on the old
ISA version.
- "out of resource" errors cause receive buffer chain corruption
- resets can confuse the interrupt handler
- multi-cast setup causes receive buffer chain corruption
- shared memory setup incomplete
* Enhance effiency by avoiding unnecessary shared memory access,
improved handling of receive frame & buffer descriptors, and
introducing an `asynchronous' option when issuing 82586 commands.
* Exclusively use offsets relative to the bus handle representing the shared
memory area to formulate accesses to the chip's data-structures. The
front-ends provide glue functions that cater to the chip's endian-
sensitivity, to perform the actual device access (note: single-byte
accesses are done here using `bus_space_{read,write}_1()').
This concludes the transformation into a bus-independent driver module.
* Abolish C structures to access chip data-structures; instead use macros
that take indices and offsets relative to the bus handle representing
the chip's resources.
* Include the old version of this file wholesale, until all drivers
have been updated to use the MI 82586 code.
- allow get/set of enums SUNAUDIO_SOURCE and SUNAUDIO_OUTPUT rather
than returning EINVAL
- add missing SUNAUDIO_MONITOR_CLASS case in query_devinfo
- convert SUNAUDIO_MONITOR case from a MIXER_CLASS to a MIXER_VALUE
like it is supposed to be
- the labels for outputs/record class were swapped: fix it
this patch allows "mixerctl" to work properly on a sparc
- Closing the audio device should stop recording.
- Manipulating the pause function could accidentally start playing or recording.
- AUDIO_FLUSH could accidentally start playing or recording.
- guard against synchronous I/O completion
- avoid race conditions
- use bgetvp/brelvp to properly maintain the vnode holdcount
and clean/dirty buffer lists.
the historical link? flags for media select)
XXX No pullup request for this. But if sysinst supports explicit media
XXX selection in 1.3, this should be in 1.3 as well.
does a "restore data pointers" when reselected after disconnecting in
the middle of a DMA transfer). The driver needs a different way to know
which script to continue the DMA transfer. The message-in for the "restore
data pointers" loses the original "resume" script, and the driver would
attempt to continue the DMA transfer at the beginning of the current DMA
chunk, rather than at the point the disconnect occured. The result was a
spurious console message, and a trashed filesystem.
clobbers my SMC. Now I can really use a generic kernel with my SMC @0x300.
This change has been tested on various machines with ne2000 and 3c509 baords.
XXX All these probes sould be reordered after the release, with invasive
XXX probes at the end.
to be reloaded every time it is checked. This avoids a condition where
it can be cached in a register in such a way that updates to the flags in
an interrupt handler to not be noticed, which in turn causes the process
doing the i/o to sleep forever. Bug report and suggested fix from
Hiroshi HORIMOTO <horimoto@cs-yuugao.cs.sist.ac.jp>, PR $4460.
nullbuf (used to pad packets < ETHER_MIN_SIZE) is used for all tl
interfaces. Allocates only once, and never deallocate it (as we can't say
if another instance of the driver is interface is using it).
i/o-mapped space to always be used), we discover that at least one
ThunderLAN interface can't read the EEPROM properly if memory-mapped
access is used. Kludge around this for now by "prefering" i/o space.
to look specifically at the address it was provided *only*, since the
scan isn't safe (it can stomp on cards that will be probed later, like
NE2000 clones).
- Do PCI space configuration like the other drivers. In particular,
don't _disable_ the space we're not using because some lame firmware
implementations might not reenable it on warm boot. Also, prefer
memory space always.
- Make match and info-gathering in attach table-driven.
- Rearrange things a bit to be a bit more visually pleasing during boot.
Also, fixup some #include problems.
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
fvdl