stack-allocate a sockaddr_storage for the temporary sockaddr rather
than putting it in an mbuf.
neighbor discovery wants to delete expired ifa's from a timeout
handler. allowing rtinit(RTM_DELETE, ...) to run at interrupt level
allows this to work.
i think we can afford the extra ~128 bytes of stack depth ..
This is important, because for most protocols, link level fragmentation is
used, but with different default effective MTUs. (e.g.: IPv4 default MTU
is 1500 octets, IPv6 default MTU is 9072 octets).
This situation happens on severe memory shortage. We may need more
improvements here and there.
- Grab IEEE802 address from IFT_ETHER card, even if the card is
inserted after bootup time. Is there any other card that can be
inserted afterwards? pcmcia fddi card? :-P
- RFC2373 u bit handling suggests that we SHOULD NOT copy interface id from
ethernet card to pseudo interface, when ethernet card has IEEE802/EUI64
with u bit != 0 (this means that IEEE802/EUI64 is not universally unique).
Do not use such address as, for example, interface id for gif interface.
(I have such an ethernet card myself)
This may change interface id for your gif interface. be careful upgrading
rc files.
(sync with recent KAME)
Tree structure:
- sys/arch/sh3: sh3 generic code
As commented, in-chip device drivers are put into sys/arch/sh3/dev.
- sys/arch/evbsh3: sh3 evaluation boards (pure sh3 CPU, no fancy external HW)
- sys/arch/mmeye: Brains mmEye, www.brains.co.jp
MI source code includes couple of #ifdef for sh3-coff support.
(sh3 uses coff or elf)
Needs some more improvements, especialy in sys/arch/sh3/conf/files.sh3,
to compile the tree (due to last minute tree structure change).
again when switching link0 on.
XXX This stuff needs to be thought about, especially with the doomming IPv6
support, which uses yet another default mtu.
which can't be handled by netmask, and ifa_ifwithnet() didn't find the
interface associated with an adress if it was in the same block but not with
the same prefix. This prevented 'route add' and atalkd to work properly
with some network configs.
This has been discussed on tech-net some weeks ago.
(Sorry for a big commit, I can't separate this into several pieces...)
Pls check sys/netinet6/TODO and sys/netinet6/IMPLEMENTATION for details.
- sys/kern: do not assume single mbuf, accept chained mbuf on passing
data from userland to kernel (or other way round).
- "midway" ATM card: ATM PVC pseudo device support, like those done in ALTQ
package (ftp://ftp.csl.sony.co.jp/pub/kjc/).
- sys/netinet/tcp*: IPv4/v6 dual stack tcp support.
- sys/netinet/{ip6,icmp6}.h, sys/net/pfkeyv2.h: IETF document assumes those
file to be there so we patch it up.
- sys/netinet: IPsec additions are here and there.
- sys/netinet6/*: most of IPv6 code sits here.
- sys/netkey: IPsec key management code
- dev/pci/pcidevs: regen
In my understanding no code here is subject to export control so it
should be safe.
after various m_adj()s have been done. Kludge around this with a cheesy
macro that knows where the drivers put the mac header in the first mbuf.
XXX There should be a better way to do this.
directly, call the function pointer (*if_input)(ifp, m). The input routine
expects the packet header to be at the head of the packet, and will adjust
as necessary. Privatize the layer 2 input and output routines, allowing
*_ifattach() to set them up as appropriate.
and "pass-filter" and "inbound" and "outbound" qualifiers in the filter
expression, use new "active-filter-in", "active-filter-out", "pass-filter-in",
and "pass-filter-out" without these qualifiers.
This is necessary due to the horrible, awful way "inbound" and "outbound"
were specified for the filter programs when a packet was passed through them.
Basically, the "address" byte in the serial PPP header was overwritten with
a value to indicate the direction. However, the "address" byte doesn't even
exist on PPP headers for all other PPP encaps! So, this old method worked
only for serial encaps, and corrupted packets for all others (PPPoE, ATM, etc.)
to serial encap, change its data link type to DLT_PPP_SERIAL.
* Work around some serious bogosity in the filtering code which utterly
breaks proper functioning of BPF. The PPP code and pppd(8) WILL be changed
to fix this.
select the current medium, (and it is not autoselect), assume no change and
do not try to select the medium. Fixes 'ifconfig le0 medium 10base5' on sparc2
without requiring a 'do nothing' mediachange callback.
matt