PR/37692 from Yojiro UO
---
uhmodem: device driver for huawei 3G wireless modem
* what it is?
A device driver for huawei 3G wireless modem, E220 and its valiations.
The devices are very simuler to ubsa device, but they need special care
to use as modem device.
This patch introduce "uhmodem (USB Huawei modem)" for the devices.
A uhmodem device has two com devices and one USB mass strage device.
The driver enable to use all of them.
* dmesg:
uhmodem0 at uhub0 port 1 configuration 1 interface 0
uhmodem0: HUAWEI Technologies HUAWEI Mobile, rev 1.10/0.00, addr 2
uhmodem0: mass storage only mode, reattach to enable modem
uhmodem0: at uhub0 port 1 (addr 2) disconnected
uhmodem0 detached
uhmodem0 at uhub0 port 1 configuration 1 interface 0
uhmodem0: HUAWEI Technologies HUAWEI Mobile, rev 1.10/0.00, addr 2
ucom0 at uhmodem0 portno 0: modem
ucom1 at uhmodem0 portno 1: monitor
umass0 at uhub0 port 1 configuration 1 interface 2
umass0: HUAWEI Technologies HUAWEI Mobile, rev 1.10/0.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
cd0 at scsibus0 target 0 lun 0: <HUAWEI, Mass Storage, 2.31> cdrom removable
- The driver now uses the Super I/O address port as port argument in
the configuration file. The Environmental Controller base address is
fetched by the Super I/O EC LDN configuration registers.
- Invalidate voltage sensors if data returned is 0xff.
- Use the Super I/O Global Configuration Registers Chip ID[12] and Device
Revision to store/print the correct information.
- Use only the Fan Extended Tachometer registers on IT871[68]F for now;
this gives us correct data for IT8705/IT8712F again.
Inspired by the smsc(4) driver. The UPDATING file has been updated to
reflect the rename.
This gets rid of the now-unneded "todclock" and "todservice" attributes
from the footbridge device files, which should allow netwinder to build
again after its conversion to generic TODR.
Resulting kernel verified to boot up OK on gxemul (after my recent
fixes of the gxemul package to emulate free-running timers).
The PIOBM is used by only one driver (will be added later,
stay tuned) and intruduce an attribute "ata_piobm" so that
it will be conditionally compiled in.
The "ata_dma" (busmastering transfer using ATA DMA mode) and
"ata_udma" (busmastering transfer using ATA Ultra DMA mode)
attributes are also added for consistency, but unused for now.
dev/ic/wd33c93.c. This may not be the best WD33C93 driver we've
got, but it's the most recently worked on and probably the most
portable, so it seems like a good basis for further work (and in
particular an acorn26 driver for the Acorn SCSI card). There's
no functional change in this commit, and sgimips kernels still
compile.
While it can be made to compile, the paradigm is not quite right because
it attempts to contact the filesystem during autoconfig which sometimes
causes a panic. Even if that was fixed, there is another potential problem
in that the driver tries/sleeps/tries/sleeps and the sleep could
theoretically sleep past the rc.d/btconfig stage and the controller
would remain unconfigured.
So, I have prepared a different method for loading the firmware to
Broadcom BCM2033 chip based devices. A package 'sysutils/bcmfw' will load
the firmware files via a ugen(4) device interface.
This update removes the ubtbcmfw(4) driver and adds a table to the ubt(4)
driver so that it will not attach to Broadcom BCM2033 based devices before
the firmware was loaded.
This fixes kern/34219
Remove bthset(4) device and add btsco(4) in its place. This is an
improved version which is not just for headsets, as it can receive
incoming connections (eg for Hands Free Profile). Update bthset(1)
control utlitiy to relate to new device.
Change the way in which bluetooth devices attach to system. The
new way is for devices to attach directly to a btdevN device via
its own control file /dev/btdevN.
- bthub(4) is replaced by btdev(4).
- /dev/bthubctl is replaced by /dev/btdevN.
- configuration now uses proplib(3) property lists.
- btcontrol(8) updated to use new API, and now uses private
- XML config file /var/db/btdev.xml.
NetBSD Foundation Membership still pending.) This stack was written by
Iain under sponsorship from Itronix Inc.
The stack includes support for rfcomm networking (networking via your
bluetooth enabled cell phone), hid devices (keyboards/mice), and headsets.
Drivers for both PCMCIA and USB bluetooth controllers are included.
of digital video recorders popular in Europe and Australia.
These devices have a USB client port which can be used to upload and
download recordings (and other files, such as MIPS binaries for execution
on the DVR's CPU) to/from their internal hard disk, in addition to some
other operations on files and directories.
and ADT 7463c thermal and voltage monitor found on the Tyan S2881 and S2882-D
(and probably other boards as well). We do not currently support any kind
of detection of the i2c address of the thermal monitor; it appears to be
at 0x2D on the S2881 and 0x2E on the S2882-D (kernel config examples
forthcoming).
From PR kern/32463 submitted by Anil Gopinath, anil_public@yahoo.com.
xtraeme