Do a little mbuf rework while here. Change all uses of MGET*(*, M_WAIT, *)
to m_get*(M_WAIT, *). These are not performance critical and making them
call m_get saves considerable space. Add m_clget analogue of MCLGET and
make corresponding change for M_WAIT uses.
Modify netinet, gem, fxp, tulip, nfs to support MBUFTRACE.
Begin to change netstat to use sysctl.
malloc types into a structure, a pointer to which is passed around,
instead of an int constant. Allow the limit to be adjusted when the
malloc type is defined, or with a function call, as suggested by
Jonathan Stone.
variant also zeroes the counters after copying them). In ifunit, add
support for dealing all numeric ifname by treating them as an ifindex
which is used to look up the interface.
Add capabilities bits that indicate an interface can only perform
in-bound TCPv4 or UDPv4 checksums. There is at least one Gig-E chip
for which this is true (Level One LXT-1001), and this is also the
case for the Intel i82559 10/100 Ethernet chips.
network interfaces. This works by pre-computing the pseudo-header
checksum and caching it, delaying the actual checksum to ip_output()
if the hardware cannot perform the sum for us. In-bound checksums
can either be fully-checked by hardware, or summed up for final
verification by software. This method was modeled after how this
is done in FreeBSD, although the code is significantly different in
most places.
We don't delay checksums for IPv6/TCP, but we do take advantage of the
cached pseudo-header checksum.
Note: hardware-assisted checksumming defaults to "off". It is
enabled with ifconfig(8). See the manual page for details.
Implement hardware-assisted checksumming on the DP83820 Gigabit Ethernet,
3c90xB/3c90xC 10/100 Ethernet, and Alteon Tigon/Tigon2 Gigabit Ethernet.
have sys/net/route.c:rtrequest1(), which takes rt_addrinfo * as the argument.
pass rt_addrinfo all the way down to rtrequest, and ifa->ifa_rtrequest.
3rd arg of ifa->ifa_rtrequest is now rt_addrinfo * instead of sockaddr *
(almost noone is using it anyways).
benefit: the follwoing command now works. previously we need two route(8)
invocations, "add" then "change".
# route add -inet6 default ::1 -ifp gif0
remove unsafe typecast in rtrequest(), from rtentry * to sockaddr *. it was
introduced by 4.3BSD-reno and never corrected.
XXX is eon_rtrequest() change correct regarding to 3rd arg?
eon_rtrequest() and rtrequest() were incorrect since 4.3BSD-reno,
so i do not have correct answer in the source code.
someone with more clue about netiso-over-ip, please help.
the link level name for the interface (ifp->if_sadl) is allocated
before ifp->if_addrlen is initialized, which could lead to allocating
too little space for the link level address.
Do this by splitting allocation of the link level name out of
if_attach() and into if_alloc_sadl(), which is normally called
by functions like ether_ifattach(). Network interfaces which
don't have a link-specific attach routine must call if_alloc_sadl()
themselves (example: gif).
Link level names are freed by if_free_sadl(), which can be called
from e.g. ether_ifdetach(). Drivers never need call if_free_sadl()
themselves as if_detach() will do it if it is not already done.
While here, add the ability to pass an AF_LINK address to
SIOCSIFADDR in ether_ioctl() (this is what caused me to notice
the problem that the above fixes).
interferes with the reference counting done by ifpromisc(), and is
essentially impossible to get the semantics correct if we allow this
flag to be directly toggled.
No programs should really be affected by this; IFF_PROMISC is basically
useless without bpf, anyway, and bpf still provides a way to set
promiscuous mode on an interface (which uses ifpromisc()).
parties can easily know the state of a link.
- Define an interface announcement message for the routing socket so that
routing daemons and other interested parties know when an interface
is attached/detached.
although this version has been changed somewhat:
- reference counting on ifaddrs isn't as complete as Bill's original
work was. This is hard to get right, and we should attack one
protocol at a time.
- This doesn't do reference counting or dynamic allocation of ifnets yet.
- This version introduces a new PRU -- PRU_PURGEADDR, which is used to
purge an ifaddr from a protocol. The old method Bill used didn't work
on all protocols, and it only worked on some because it was Very Lucky.
This mostly works ... i.e. works for my USB Ethernet, except for a dangling
ifaddr reference left by the IPv6 code; have not yet tracked this down.
due to massive changes in KAME side.
- IPv6 output goes through nd6_output
- faith can capture IPv4 packets as well - you can run IPv4-to-IPv6 translator
using heavily modified DNS servers
- per-interface statistics (required for IPv6 MIB)
- interface autoconfig is revisited
- udp input handling has a big change for mapped address support.
- introduce in4_cksum() for non-overwriting checksumming
- introduce m_pulldown()
- neighbor discovery cleanups/improvements
- netinet/in.h strictly conforms to RFC2553 (no extra defs visible to userland)
- IFA_STATS is fixed a bit (not tested)
- and more more more.
TODO:
- cleanup os-independency #ifdef
- avoid rcvif dual use (for IPsec) to help ifdetach
(sorry for jumbo commit, I can't separate this any more...)
RTM_IFINFO is now 0xf, 0xe is RTM_OIFINFO which returns the old (if_msghdr14)
struct with 32bit counters (binary compat, conditioned on COMPAT_14).
Same for sysctl: node 3 is renamed NET_RT_OIFLIST, NET_RT_IFLIST is now node 4.
Change rt_msg1() to add an mbuf to the mbuf chain instead of just panic()
when the message is larger than MHLEN.
deal correctly with more than 32767 routes out an interface.
Should close PR 7148 regarding problems when ifs_refcnt overflows.
Bump kernel version from 1.4L to 1.4M.
(Sorry for a big commit, I can't separate this into several pieces...)
Pls check sys/netinet6/TODO and sys/netinet6/IMPLEMENTATION for details.
- sys/kern: do not assume single mbuf, accept chained mbuf on passing
data from userland to kernel (or other way round).
- "midway" ATM card: ATM PVC pseudo device support, like those done in ALTQ
package (ftp://ftp.csl.sony.co.jp/pub/kjc/).
- sys/netinet/tcp*: IPv4/v6 dual stack tcp support.
- sys/netinet/{ip6,icmp6}.h, sys/net/pfkeyv2.h: IETF document assumes those
file to be there so we patch it up.
- sys/netinet: IPsec additions are here and there.
- sys/netinet6/*: most of IPv6 code sits here.
- sys/netkey: IPsec key management code
- dev/pci/pcidevs: regen
In my understanding no code here is subject to export control so it
should be safe.
christos