now makes use of lockmgr(). Since we broke into the debugger from an interrupt,
we don't have a curproc, so when lockmgr() tries to find our PID it barfs,
causing another break into DDB which then calls the mysterious code that
calls lockmgr() again.....
So set doing_shutdown while we're in DDB so lockmgr ignores locks.
grf-type consoles (wscons). Config_console() is now called from consinit(),
just after setting up the kernel msgbuf, so debugging is easy(er).
To further facilitate this move, the pcibus now allows for early-console
attaches by allocating static bus_space_tags (no mallocs possible at this
point).
can not cross a page boundary. This fixes a problem when a dump(8) buffer
just crossed a page boundary and bus_dmamap_load() would coalesce the
the overlap onto the first segment. The NEXTPTR value would get set to
-1 when starting the DMA transfer and the residual data for unaligned
transfers would be copied to physical address 0x1ffffffc. On the R3000,
this would result in corrupted data, and on the R4000 would usually result
in a hard system hang.
both the primary and the secondary caches. MachFlushDCache() will not
invalidate the correct secondary cache lines for KSEG2 addresses.
R4000 systems should now be able to boot and run.
addresses, it makes sense to print the actual address of the device rather
than the original address. The latter is useful to distinguish the type
of device only, so we maintain that data internally (as we always have).
This closes PR 10557 from Dave Huang.
you do not save it and pass it along in rval the system will start
to fail running user programs. This finishes the suggestion by cgd to
not save some registers on syscall entry.
we have to poke the data structures directly to force the offset we need.
The open() function returns with the address of the IO control block in
register t0 so we take a copy of it for our brute-force lseek function.
This should be reasonably portable since the firmware writers closely
follow UNIX semantics and the open stubs should recompile and use the
same registers. May break on the rebadged clones -- buyer beware.
The alternative is to use dummy reads to go forwards and reopen followed
by dummy reads to go backwards. It takes around 60 seconds to boot
using this method if we use a clean filesystem.
Tested with firmware versions 5.40 and 5.43
Check the first partition type in devopen(), and if it is of type
FS_RAID, add 64 to blkdev_part_offset.
NOTE: This brings the size of the alpha first-stage bootblocks up to
close to the maximum. RAID1 support is controlled by the
BOOTXX_RAID1_SUPPORT define, and is easy to disable if size
becomes an issue.
based on it working already for macppc.
Also add commented out:
#options VNODE_OP_NOINLINE # Don't inline vnode op calls
#options NFS_V2_ONLY # Exclude NFS3 and NQNFS code
as suggestions for additional savings
maps standard boot flags to corresponding RB_* values
use BOOT_FLAG() in port's MD code as appropriate
as discussed on tech-kern, add new boot flags -v, -q for booting
verbosely or quietly, and corresponding AB_VERBOSE/AB_QUIET
boot flags; also add FreeBSD-compatible bootverbose macro and
NetBSD-specific bootquiet macro
for hpcmips, use new bootverbose instead of it's own hpcmips_verbose
Tested on i386, and to limited extend (compile of affected files) also for
mvme68k, hp300, luna68k, sun3.
* All of pmap_init is now deferred to the first call of pmap_create. This
allows us to allocate stuff dynamically using malloc.
* pv_table (which is needed before malloc is available) is temporarily
allocated using pmap_steal_memory in pmap_bootstrap, and then
re-allocated using malloc in pmap_create, with the old allocation being
given back to UVM. This should save some memory on small machines, but
the malloc overhead probably soaks it up.
the fmovecr constant table has the internal format
of the constants. So, when changing the mantissa size by a
non-multiple of 32 bits, we'd have to change this table, too. As
all other code changes just chopped of the least significand
32bit word of the mantissa, we correct the mantissa size instead
to (115 - 32 == 83) bits.
fpu_fmovecr.c:
put a safety belt in, to catch the next person who doesn't know this.
fpu_int.c:
in one place, the reduction of the mantissa size was overlooked.
fpu_log.c:
as the most significand 32bit word of the mantissa was changed back to the
old format, change back the table indexing code, too.
This should fix PR 11045.
indeed tagged with ASM and the ASN, "per the Alpha architecture".
It is therefore safe to cancel any pending lazy I-sync on a
given CPU when a new ASN is assigned on that CPU.
wdk