"key" and a "dlt", use a "type" (PFIL_TYPE_{AF,IFNET} for now) and
a val/ptr appropriate for that type. This allows for more future
flexibility with the pfil_hook mechanism.
mandatory for IPv6 (so we can't just validate by using connected pcb - we need
to allow traffic from unconnected pcb to do pmtud).
- if the traffic is validated by xx_ctlinput, allow up to "hiwat" pmtud
route entries.
- if the traffic was not validated by xx_ctlinput, allow up to "lowat" pmtud
route entries (there's upper limit, so bad guys cannot blow up our routing
table).
sync with kame
XXX need to think again about default hiwat/lowat value.
XXX victim selection to help starvation case
- All packets are passed to PFIL_HOOKS as they come off the wire, i.e.
fields in protocol headers in network order, etc.
- Allow for multiple hooks to be registered, using a "key" and a "dlt".
The "dlt" is a BPF data link type, indicating what type of header is
present.
- INET and INET6 register with key == AF_INET or AF_INET6, and
dlt == DLT_RAW.
- PFIL_HOOKS now take an argument for the filter hook, and mbuf **,
an ifnet *, and a direction (PFIL_IN or PFIL_OUT), thus making them
less IP (really, IP Filter) centric.
Maintain compatibility with IP Filter by adding wrapper functions for
IP Filter.
Current status:
Only OHCI chip is supported (fwohci).
ping (IPv4) works with Sony's implementation (SmartConnect) on Win98.
sometimes works but not stable.
Not implemented yet:
IRM (Isochronous Resource Manager) functionality.
Link layer fragmentation.
Topology map.
More to do:
clean ups
MCAP
charactor device part
dhcp
There is no entry in GENERIC config file yet.
Follow sys/dev/ieee1394/IMPLEMENTATION to enable if_fw.
in add_m6fc(), set interface list for all cases.
in response to a report from Hoerdt Mickael.
kame 1.31 -> 1.32
discard PIM register if the version of the inner packet is incorrect (i.e. IPv6)
(according to clarfication of recent discussion in the IETF pim ML)
TODO: udp6, and sendto consideration. as pmtud is mandatory for IPv6,
it is rather important for us to support those cases.
TODO: more testing
TODO: kame sync
entering rtentry's for hosts we're not actually communicating
with.
Do this by invoking the ctlinput for the protocol, which is
responsible for validating the ICMP message:
* TCP -- Lookup the connection based on the address/port
pairs in the ICMP message.
* AH/ESP -- Lookup the SA based on the SPI in the ICMP message.
If validation succeeds, ctlinput is responsible for calling
icmp_mtudisc(). icmp_mtudisc() then invokes callbacks registered
by protocols (such as TCP) which want to take some sort of special
action when a path's MTU changes. For TCP, this is where we now
refresh cached routes and re-enter slow-start.
As a side-effect, this fixes the problem where TCP would not be
notified when a path's MTU changed if AH/ESP were being used.
XXX Note, this is only a fix for the IPv4 case. For the IPv6
XXX case, we need to wait for the KAME folks.
Reviewed by sommerfeld@netbsd.org and itojun@netbsd.org.
if there's no rnd(4), random(9) will be used with one-time warning printf(9).
XXX not sure how good rnd_extract_data(RND_EXTRACT_ANY) is, under entropy-
starvation situation
- use of IPv4 mapped address on outbound socket
- explicit port numbers via sendto().
old code grabbed port number from inpcb/in6pcb.
in the above case, old code failed to lookup ipsec policy (oops).
sync with kame.
- correct byte lifetime computation to conform to RFC2401 p23 (use
packet BEFORE compression)
- stabilize deflate calls
- present error messages better
