(mail@janderson.ca): remove ieee80211_ibss_merge's TSFT argument.
Do the TSFT comparison in the drivers (ath, atw). Remove a lot of
extraneous debug statements from ieee80211_ibss_merge.
Set the ieee80211_node's state to IEEE80211_STA_BSS after it's been
copied to the ic_bss, not before.
In struct ieee80211_node, make the ni_tstamp field a union of a
uint64_t and the 8 TSF octets so that it's easier to compare a
neighbor's TSF with the local TSF.
Log IBSS merges (Greg Troxel's suggestion). Also log IBSS creation.
These are rare and important events that deserve to be logged.
are at the end of the node queue. Change the reference-counting
discipline: ni->ni_refcnt indicates how many times net80211 has
granted ni to the driver. Every node in the table with ni_refcnt=0
is eligible to be garbage-collected. The mere presence of a node
in the table does not any longer indicate its auth/assoc state;
nodes have a ni_state variable, now. A sysctl,
net.link.ieee80211.maxnodecache, controls the maximum LRU cache
size.
While I am here, patch ieee80211_find_node_for_beacon to do a "best
match" by bssid/ssid/channel, not a "perfect match." This keeps
net80211 from caching duplicate nodes in the table.
ieee80211_input():
* Do not discard management frames in station mode just because they have
the wrong BSSID.
* Do not discard beacons in station and host-AP mode when not scanning.
* Some minor rearrangement. Update node statistics even if the packet is
rejected.
ieee80211_recv_mgmt():
* Accept probe responses and beacons in station and host-AP even when not
scanning.
* Do not immediately free the node created by a beacon or probe response.
XXX Should I check BSSIDs more carefully in ieee80211_recv_mgmt() --
specifically for ASSOC_RESP, REASSOC_RESP, AUTH, DEAUTH and DISASSOC?
Fix a problem with APs that advertise multiple SSIDs:
Change the footprint of ieee80211_find_node_with_channel() to take a SSID as
well, and, if not empty, compared it with the existing nodes. This causes
us to allocate multiple nodes for the same AP. Without this we were only
leaving one SSID in the node table, which might not be the desired one, and
so the interface would fail to fully initialize. (Reported by he@ with a
Cisco 350 AP.)
will eventually share it.
In the IBSS merge logic, check conditions in a different order so
that they run faster in the common case---no merge. Fix the
rate-limiting on the debug outputs (enabled by IFF_LINK0).
Abstract some of the node management code into separate functions, and use them
throughout, plugging memory leaks.
Allocate the AID allocation map dynamically.
Change the signature of IEEE80211_DPRINTF() so that it uses a bitmask, and
convert some of the if_printf()s to IEEE80211_DPRINTF()s. XXX I'm using a
global variable at the moment rather than per-interface.
beacon-sender's ieee80211_node, if ni->ni_esslen == 0. This fixes
WEP for Matthew. I think that it also will save us from IBSS
splits.
Thanks again, Matthew Gream.
Fix authentication where I had botched it with the FreeBSD import.
(In FreeBSD, net80211 is strangely subroutine-averse, so where we
have ieee80211_auth_open and ieee80211_auth_shared, they incorporate
all of ieee80211_auth_open into ieee80211_recv_mgmt. I had not
realized that was why the 20 lines of new code.)
a different BSS, because that keeps drivers like atw from detecting
ad hoc beacons with the same SSID but different BSSID for the
purpose of IBSS merges.
This should be revisited: maybe drivers should check for beacons
before handing packets up with ieee80211_input(). However, this
restores the atw(4) to working like it did with the old 802.11
layer, and it *is* nice to re-use the 802.11 layer's packet-decode
& -dispatch code (i.e., the ic_recv_mgmt callback).
#ifdef __FreeBSD__
/* FreeBSDism */
#else
/* NetBSDism */
#endif
An important and non-obvious change is in ieee80211_mgmt_output,
#ifdef __FreeBSD__
KASSERT(m->m_pkthdr.rcvif == NULL, ("rcvif not null"));
#endif
Because NetBSD mbufs are not bzero'd like FreeBSD's, we cannot
count on rcvif == NULL.
striving to keep the diffs short and simple.
* Replace FreeBSDisms (e.g. struct arpcom) with conditionally-compiled
NetBSDism (struct ethercom).
* Add compatibility shims in ieee80211_compat.*: provide NetBSD with
if_printf, for example.
* Convert FreeBSD node mutex uses to generic node critical-section
protection (ieee80211_node_critsect_begin, _end), replace
FreeBSD atomic arithmetic with generic alternative, and implement
generics in NetBSD
* Provide NetBSD-style 802.11 ioctls
* Style nits
christos