still needs an option to specify the distribution sets from a filesystem
present in fstab.
Add "ados" to the list file recognized filesystems.
Increase label information table size to 16 to allow for 16 partitions.
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
escape character (including line continuation), unless the `-r' option
is specified:
* adopt to this behaviour, add the `-r' option to disable it;
* remove the `-e' option, which was previously necessary to get this behaviour.
+ set MAKE_PROGRAM variable in bsd.port.mk to either ${GMAKE} or
${MAKE}, and use it in do-build and do-install targets
+ if X11 package, and man pages are installed, add install.man to
${INSTALL_TARGET}, rather than using a separate command to do this.
Also added CATn= blah.0, similar to MANn= blah.1, which installs
pre-formatted man pages, like the ones imake produces.
* Change find_disks: after mouting target root, check for
/etc/fstab in target, and abort upgrade if not found.
* Change upgrade to check if the target root has /etc.old
before renaming the target /etc -> /etc.old. If found, abort.
(may indicates a failed upgrade.)
* Add save_etc(). saves target /etc as /etc.old, then copies back
config files we might want during upgrade, in case target is current root.
* Fix logic that fscks and mounts disks. Use subroutines to
fsck with a warning message and ok() on continue. Same for doing mounts.
* Fix bug in extract_dist(). Do NOT do target prefixing on the dist_dir,
since we didn't do target prefixing when mounting it.
(At least, NFS does't.)
* Add function to sanity-check target root.
Call after upgrade/install is done.
* Change MSG_realdir to print the strerror() of any errors.
Change target_chdir() to check if chdir() returns -1 and return errno.
* Make sure /dev exists before cd'ing there and running MAKEDEV.
* Use target_fopen() and fprintf() to write network state to disk,
to avoid inadvertent shell escapes.
* Fix silly typo in append_to_target_file. (maybe add shell quotes?)
with wording modified for clarity.
Last sentence of the patch omitted because I do not understand what
it means, even after some examination of the unix domain kernel code.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
per class of syscall stubs. This is much more efficient (though it's still
pretty inefficient).
This also fixes a problem with syscall.h and DESTDIR which was pretty
well buried in the old implementation.
From Chris Demetriou <cgd@pa.dec.com>.
but is a marked improvement. This takes advantage of a pseudo-DMA hardware
hack of Apple's that exposes a 16-bit register that the Apple-designed
memory controller acts like a DMA controller and handshakes into or out
of the FIFO. Wierd.
Unfortunately, there does not seem to be a good way to determine what
variety of comm-slot card is present in a machine. There is still an
interrupt issue preventing these cards from working--hopefully that will
be ironed out shortly.
normal rei course. If the handler returns non-zero, just rte.
This should allow better MACE response-time and still keep serial
interrupt overhead to a minimum on older, slower machines.
mhitch