static binary: otool). Dynamic binaires have a pointer to the Mach-O
header on the top of the stack, static binaries don't have this, and
having it produced a crash.
One bugfix: the EXEC_MACHO code assumes that entry = NULL means that
the entry point has not been found in the load commands seen so far.
Therefore we need to initialized entry to NULL if we want a static binary
to discover it. (dynamic binaries were forced to iscover it because when
the intepreter load command is found, entry is updated whatever its
value was before).
One hack: Both COMPAT_MACH and COMPAT_DARWIN are willing to run Mach-O
binaries. COMPAT_MACH fails for dynamic binaries because it cannot find
the interpreter in /emul/mach. For static binaires, it will accept them
(and for Darwin static binaries, this will cause a failure). Until we
rite a test for matchinf Darwin static binaries, just swap the order of
COMPAT_MACH and COMPAT_DARWIN in the exec switch so that COMPAT_DARWIN
is tried first (this will have the advantage of speeding up program
startup). EXECSW_PRIO_{FIRST_LAST} does not seem to work...
file system.
The function vfs_write_suspend stops all new write operations to a file
system, allows any file system modifying system calls already in progress
to complete, then sync's the file system to disk and returns. The
function vfs_write_resume allows the suspended write operations to
complete.
From FreeBSD with slight modifications.
Approved by: Frank van der Linden <fvdl@netbsd.org>
mv MNT_GONE, MNT_UNMOUNT and MNT_WANTRDWR to this field
additonally add mnt_writeopcountupper and mnt_writeopcountlower fields
in preparation for pending write suspension support work
bump kernel version to 1.6ZD
<sys/bootblock.h>:
* Added definitions for the Master Boot Record (MBR) used by
a variety of systems (primarily i386), including the format
of the BIOS Parameter Block (BPB).
This information was cribbed from a variety of sources
including <sys/disklabel_mbr.h> which this is a superset of.
As part of this, some data structure elements and #defines
were renamed to be more "namespace friendly" and consistent
with other bootblocks and MBR documentation.
Update all uses of the old names to the new names.
<sys/disklabel_mbr.h>:
* Deprecated in favor of <sys/bootblock.h> (the latter is more
"host tool" friendly).
amd64 & i386:
* Renamed /usr/mdec/bootxx_dosfs to /usr/mdec/bootxx_msdos, to
be consistent with the naming convention of the msdosfs tools.
* Removed /usr/mdec/bootxx_ufs, as it's equivalent to bootxx_ffsv1
and it's confusing to have two functionally equivalent bootblocks,
especially given that "ufs" has multiple meanings (it could be
a synonym for "ffs", or the group of ffs/lfs/ext2fs file systems).
* Rework pbr.S (the first sector of bootxx_*):
+ Ensure that BPB (bytes 11..89) and the partition table
(bytes 446..509) do not contain code.
+ Add support for booting from FAT partitions if BOOT_FROM_FAT
is defined. (Only set for bootxx_msdos).
+ Remove "dummy" partition 3; if people want to installboot(8)
these to the start of the disk they can use fdisk(8) to
create a real MBR partition table...
+ Compile with TERSE_ERROR so it fits because of the above.
Whilst this is less user friendly, I feel it's important
to have a valid partition table and BPB in the MBR/PBR.
* Renamed /usr/mdec/biosboot to /usr/mdec/boot, to be consistent
with other platforms.
* Enable SUPPORT_DOSFS in /usr/mdec/boot (stage2), so that
we can boot off FAT partitions.
* Crank version of /usr/mdec/boot to 3.1, and fix some of the other
entries in the version file.
installboot(8) (i386):
* Read the existing MBR of the filesystem and retain the BIOS
Parameter Block (BPB) in bytes 11..89 and the MBR partition
table in bytes 446..509. (Previously installboot(8) would
trash those two sections of the MBR.)
mbrlabel(8):
* Use sys/lib/libkern/xlat_mbr_fstype.c instead of homegrown code
to map the MBR partition type to the NetBSD disklabel type.
Test built "make release" for i386, and new bootblocks verified to work
(even off FAT!).
Right now the only flag is used to indicate if a ksiginfo_t is a
result of a trap. Add a predicate macro to test for this flag.
* Add initialization macros for ksiginfo_t's.
* Add accssor macro for ksi_trap. Expands to 0 if the ksiginfo_t was
not the result of a trap. This matches the sigcontext trapcode semantics.
* In kpsendsig(), use KSI_TRAP_P() to select the lwp that gets the signal.
Inspired by Matthias Drochner's fix to kpsendsig(), but correctly handles
the case of non-trap-generated signals that have a > 0 si_code.
This patch fixes a signal delivery problem with threaded programs noted by
Matthias Drochner on tech-kern.
As discussed on tech-kern. Reviewed and OK's by Christos.
* introduce fsetown(), fgetown(), fownsignal() - this sets/retrieves/signals
the owner of descriptor, according to appropriate sematics
of TIOCSPGRP/FIOSETOWN/SIOCSPGRP/TIOCGPGRP/FIOGETOWN/SIOCGPGRP ioctl; use
these routines instead of custom code where appropriate
* make every place handling TIOCSPGRP/TIOCGPGRP handle also FIOSETOWN/FIOGETOWN
properly, and remove the translation of FIO[SG]OWN to TIOC[SG]PGRP
in sys_ioctl() & sys_fcntl()
* also remove the socket-specific hack in sys_ioctl()/sys_fcntl() and
pass the ioctls down to soo_ioctl() as any other ioctl
change discussed on tech-kern@
