Eliminate obsolete global kernel variable "struct timezone tz"
Add RTC_OFFSET option
Add global kernel variable rtc_offset, which is initialized by
RTC_OFFSET at kernel compile time.
on i386, x68k, mac68k, pc532 and arm32, RTC_OFFSET indicates how many
minutes west (east) of GMT the hardware RTC runs. Defaults to 0.
Places where tz variable was used to indicate this in the past have
been replaced with rtc_offset.
Add sysctl interface to rtc_offset.
Kill obsolete DST_* macros in sys/time.h
gettimeofday now always returns zeroed timezone if zone is requested.
settimeofday now ignores and logs attempts to set non-existant kernel
timezone.
* Add IPL_HIGH. Alias IPL_HIGH to IPL_RTTY
* Define splrtty (used by the scn driver).
* Add iv_level and iv_mask to struct iv. These define the IPL at
which the handler should run.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Define SCN_RING_HIWAT and add sc_rbhiwat to scn_softc. When the
ringbuffer gets full up to this mark, rts gets asserted (Ian Dall).
* Add sc_rx_blocked to scn_softc. This is used to tell scnsoft that
rxinterrupts are blocked (Ian Dall).
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
All the following changes were provided by Ian Dall:
* Remove SCN_HSOFT. Now that the pc532's software interrupt system is running
from int14, this won't work anymore.
* Add code to detect uart type (SCN2681, SCC2692 or SCC26C92).
* Cleanup my RECOVER mess. Thank's to Ian Dall for reading the datasheet
and removing all the unnecessary RECOVERs.
* Cleanup scnrxintr.
* Implement scnhiwflow.
* Do not use automatic RTS. This and scnhiflow and some changes to the
interrupt system suggested by Ian fix the scn overrun problem at 57600
baud.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Make transfersize configurable for input and output. Default the input
transfersize to 128 bytes. That way interrupts won't be disabled for more
then about 128us-256us for slow targets. This is necessary to prevent scn
fifo overruns. Cleanup the pdma code. Thank's to Ian Dall for these
changes.
* Make it work on 30mhz machines.
* Configure MSDOSFS, CD9660, KERNFS, NFSCLIENT and INET.
* Configure SCSI-cds, slip and ppp.
* Update for mi ramdisk driver.
* Initialize iv_level for all interrupts.
* Protect the call to the sir-handler with splraise.
* intr_establish now takes *two* ipls. One at which the handler should run,
and one in which the interrupt should get blocked.
* Compute iv_mask for all interrupts in intr_establish.
on indirect-config busses a (permanent) softc that they could share
between 'match' and 'attach' routines:
Define __BROKEN_INDIRECT_CONFIG so that old autoconfiguration
interfaces are used, until drivers are converted to use the new
interfaces (actually, converted back to use the _older_ interfaces)
which prohibit indirect configuration devices from receiving a softc
in their match routine that they can share with their attach routine.
Lets users over-ride with makeoptions COPTS="..." in kernel config files.
Leave `mandatory' flags (like -msoft-float which on m68k enforces no
FP in kernel) in CFLAGS.
* Support for the new softint mechanism. Softints are now requested by
triggering an unused ICU hardware interrupt. The idea for this was
contributed by Phil Budne.
* Real probe code added.
* Duart info is now allocated only for devices that are present.
* Added IO-Recovery delays for 30mhz systems.
* Removed a few potential NULL-pointer references.
matthias