variant also zeroes the counters after copying them). In ifunit, add
support for dealing all numeric ifname by treating them as an ifindex
which is used to look up the interface.
that other parts of the kernel won't lose gratuitously. There are
places where it's assumed that it won't grow that large.
(2) Avoid accidental reuse of occupied slots in the ifindex2ifnet[]
table.
Add capabilities bits that indicate an interface can only perform
in-bound TCPv4 or UDPv4 checksums. There is at least one Gig-E chip
for which this is true (Level One LXT-1001), and this is also the
case for the Intel i82559 10/100 Ethernet chips.
follows BSD/OS practice and ucd-snmp code (FreeBSD does it for specific
interfaces only).
was: if_lastchange get updated on every packet transmission/receipt.
now: if_lastchange get updated when IFF_UP is changed.
network interfaces. This works by pre-computing the pseudo-header
checksum and caching it, delaying the actual checksum to ip_output()
if the hardware cannot perform the sum for us. In-bound checksums
can either be fully-checked by hardware, or summed up for final
verification by software. This method was modeled after how this
is done in FreeBSD, although the code is significantly different in
most places.
We don't delay checksums for IPv6/TCP, but we do take advantage of the
cached pseudo-header checksum.
Note: hardware-assisted checksumming defaults to "off". It is
enabled with ifconfig(8). See the manual page for details.
Implement hardware-assisted checksumming on the DP83820 Gigabit Ethernet,
3c90xB/3c90xC 10/100 Ethernet, and Alteon Tigon/Tigon2 Gigabit Ethernet.
have sys/net/route.c:rtrequest1(), which takes rt_addrinfo * as the argument.
pass rt_addrinfo all the way down to rtrequest, and ifa->ifa_rtrequest.
3rd arg of ifa->ifa_rtrequest is now rt_addrinfo * instead of sockaddr *
(almost noone is using it anyways).
benefit: the follwoing command now works. previously we need two route(8)
invocations, "add" then "change".
# route add -inet6 default ::1 -ifp gif0
remove unsafe typecast in rtrequest(), from rtentry * to sockaddr *. it was
introduced by 4.3BSD-reno and never corrected.
XXX is eon_rtrequest() change correct regarding to 3rd arg?
eon_rtrequest() and rtrequest() were incorrect since 4.3BSD-reno,
so i do not have correct answer in the source code.
someone with more clue about netiso-over-ip, please help.
the link level name for the interface (ifp->if_sadl) is allocated
before ifp->if_addrlen is initialized, which could lead to allocating
too little space for the link level address.
Do this by splitting allocation of the link level name out of
if_attach() and into if_alloc_sadl(), which is normally called
by functions like ether_ifattach(). Network interfaces which
don't have a link-specific attach routine must call if_alloc_sadl()
themselves (example: gif).
Link level names are freed by if_free_sadl(), which can be called
from e.g. ether_ifdetach(). Drivers never need call if_free_sadl()
themselves as if_detach() will do it if it is not already done.
While here, add the ability to pass an AF_LINK address to
SIOCSIFADDR in ether_ioctl() (this is what caused me to notice
the problem that the above fixes).
attempting to enable promisc would result in ENETDOWN. Change this to
allow the interface to always be placed in promiscuous mode, regardless
of IFF_UP. When the interface does come up, the IFF_PROMISC flag will
be consulted, and this matches the behavior that disabling promiscuous
mode has.
