try to do a better job of figuring out the EEPROM size; the old code
didn't work on (some?) 557-based cards
This commit is contained in:
joda
parent
a15ba40c30
commit
d7496546b5
@ -1,4 +1,4 @@
|
||||
/* $NetBSD: i82557.c,v 1.12 1999/11/12 18:14:18 thorpej Exp $ */
|
||||
/* $NetBSD: i82557.c,v 1.13 1999/11/19 15:19:14 joda Exp $ */
|
||||
|
||||
/*-
|
||||
* Copyright (c) 1997, 1998, 1999 The NetBSD Foundation, Inc.
|
||||
@ -181,6 +181,7 @@ int fxp_add_rfabuf __P((struct fxp_softc *, bus_dmamap_t, int));
|
||||
int fxp_mdi_read __P((struct device *, int, int));
|
||||
void fxp_statchg __P((struct device *));
|
||||
void fxp_mdi_write __P((struct device *, int, int, int));
|
||||
void fxp_autosize_eeprom __P((struct fxp_softc*));
|
||||
void fxp_read_eeprom __P((struct fxp_softc *, u_int16_t *, int, int));
|
||||
void fxp_get_info __P((struct fxp_softc *, u_int8_t *));
|
||||
void fxp_tick __P((void *));
|
||||
@ -484,30 +485,14 @@ fxp_get_info(sc, enaddr)
|
||||
CSR_WRITE_4(sc, FXP_CSR_PORT, FXP_PORT_SELECTIVE_RESET);
|
||||
DELAY(10);
|
||||
|
||||
/*
|
||||
* Figure out EEPROM size.
|
||||
*
|
||||
* Cards can have either 64-word or 256-word EEPROMs, with
|
||||
* addresses fed in using a bit-at-a-time protocol, MSB first.
|
||||
*
|
||||
* XXX this is probably not the best way to do this; the linux
|
||||
* driver does a checksum of the eeprom, but there is
|
||||
* (AFAIK) no on-line documentation on what this checksum
|
||||
* should look like (you could just steal the code from
|
||||
* linux, but that's cheating); for now we just use the fact
|
||||
* that the upper two bits of word 10 should be 01
|
||||
*/
|
||||
for(sc->sc_eeprom_size = 6;
|
||||
sc->sc_eeprom_size <= 8;
|
||||
sc->sc_eeprom_size += 2) {
|
||||
fxp_read_eeprom(sc, &data, 10, 1);
|
||||
if((data & 0xc000) == 0x4000)
|
||||
break;
|
||||
sc->sc_eeprom_size = 0;
|
||||
fxp_autosize_eeprom(sc);
|
||||
if(sc->sc_eeprom_size == 0) {
|
||||
printf("%s: failed to detect EEPROM size", sc->sc_dev.dv_xname);
|
||||
sc->sc_eeprom_size = 6; /* XXX panic here? */
|
||||
}
|
||||
if(sc->sc_eeprom_size > 8)
|
||||
panic("%s: failed to get EEPROM size", sc->sc_dev.dv_xname);
|
||||
#ifdef DEBUG
|
||||
printf("%s: assuming %d word EEPROM\n",
|
||||
printf("%s: detected %d word EEPROM\n",
|
||||
sc->sc_dev.dv_xname,
|
||||
1 << sc->sc_eeprom_size);
|
||||
#endif
|
||||
@ -527,6 +512,83 @@ fxp_get_info(sc, enaddr)
|
||||
bcopy(myea, enaddr, ETHER_ADDR_LEN);
|
||||
}
|
||||
|
||||
/*
|
||||
* Figure out EEPROM size.
|
||||
*
|
||||
* 559's can have either 64-word or 256-word EEPROMs, the 558
|
||||
* datasheet only talks about 64-word EEPROMs, and the 557 datasheet
|
||||
* talks about the existance of 16 to 256 word EEPROMs.
|
||||
*
|
||||
* The only known sizes are 64 and 256, where the 256 version is used
|
||||
* by CardBus cards to store CIS information.
|
||||
*
|
||||
* The address is shifted in msb-to-lsb, and after the last
|
||||
* address-bit the EEPROM is supposed to output a `dummy zero' bit,
|
||||
* after which follows the actual data. We try to detect this zero, by
|
||||
* probing the data-out bit in the EEPROM control register just after
|
||||
* having shifted in a bit. If the bit is zero, we assume we've
|
||||
* shifted enough address bits. The data-out should be tri-state,
|
||||
* before this, which should translate to a logical one.
|
||||
*
|
||||
* Other ways to do this would be to try to read a register with known
|
||||
* contents with a varying number of address bits, but no such
|
||||
* register seem to be available. The high bits of register 10 are 01
|
||||
* on the 558 and 559, but apparently not on the 557.
|
||||
*
|
||||
* The Linux driver computes a checksum on the EEPROM data, but the
|
||||
* value of this checksum is not very well documented.
|
||||
*/
|
||||
|
||||
void
|
||||
fxp_autosize_eeprom(sc)
|
||||
struct fxp_softc *sc;
|
||||
{
|
||||
u_int16_t reg;
|
||||
int x;
|
||||
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, FXP_EEPROM_EECS);
|
||||
/*
|
||||
* Shift in read opcode.
|
||||
*/
|
||||
for (x = 3; x > 0; x--) {
|
||||
if (FXP_EEPROM_OPC_READ & (1 << (x - 1))) {
|
||||
reg = FXP_EEPROM_EECS | FXP_EEPROM_EEDI;
|
||||
} else {
|
||||
reg = FXP_EEPROM_EECS;
|
||||
}
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, reg);
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL,
|
||||
reg | FXP_EEPROM_EESK);
|
||||
DELAY(1);
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, reg);
|
||||
DELAY(1);
|
||||
}
|
||||
/*
|
||||
* Shift in address, wait for the dummy zero following a correct
|
||||
* address shift.
|
||||
*/
|
||||
for (x = 1; x <= 8; x++) {
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, FXP_EEPROM_EECS);
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL,
|
||||
FXP_EEPROM_EECS | FXP_EEPROM_EESK);
|
||||
DELAY(1);
|
||||
if((CSR_READ_2(sc, FXP_CSR_EEPROMCONTROL) &
|
||||
FXP_EEPROM_EEDO) == 0)
|
||||
break;
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, FXP_EEPROM_EECS);
|
||||
DELAY(1);
|
||||
}
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, 0);
|
||||
DELAY(1);
|
||||
if(x != 6 && x != 8) {
|
||||
#ifdef DEBUG
|
||||
printf("%s: strange EEPROM size (%d)\n",
|
||||
sc->sc_dev.dv_xname, 1 << x);
|
||||
#endif
|
||||
} else
|
||||
sc->sc_eeprom_size = x;
|
||||
}
|
||||
|
||||
/*
|
||||
* Read from the serial EEPROM. Basically, you manually shift in
|
||||
* the read opcode (one bit at a time) and then shift in the address,
|
||||
@ -567,13 +629,13 @@ fxp_read_eeprom(sc, data, offset, words)
|
||||
*/
|
||||
for (x = sc->sc_eeprom_size; x > 0; x--) {
|
||||
if ((i + offset) & (1 << (x - 1))) {
|
||||
reg = FXP_EEPROM_EECS | FXP_EEPROM_EEDI;
|
||||
reg = FXP_EEPROM_EECS | FXP_EEPROM_EEDI;
|
||||
} else {
|
||||
reg = FXP_EEPROM_EECS;
|
||||
reg = FXP_EEPROM_EECS;
|
||||
}
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, reg);
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL,
|
||||
reg | FXP_EEPROM_EESK);
|
||||
reg | FXP_EEPROM_EESK);
|
||||
DELAY(1);
|
||||
CSR_WRITE_2(sc, FXP_CSR_EEPROMCONTROL, reg);
|
||||
DELAY(1);
|
||||
|
||||
Loading…
Reference in New Issue
Block a user