From 546c12c03ba9579c0b2771b8c6171aff8e919790 Mon Sep 17 00:00:00 2001 From: scw Date: Sat, 10 Apr 1999 16:16:11 +0000 Subject: [PATCH] Modify the example on setting the date/time so it is kosher for 1999. Fix the 'bo' command example for booting from tape on mvme167. --- distrib/notes/mvme68k/install | 12 +++++++----- distrib/notes/mvme68k/prep | 10 +++++----- 2 files changed, 12 insertions(+), 10 deletions(-) diff --git a/distrib/notes/mvme68k/install b/distrib/notes/mvme68k/install index dabf918c9b22..de04e97c3b16 100644 --- a/distrib/notes/mvme68k/install +++ b/distrib/notes/mvme68k/install @@ -1,4 +1,4 @@ -.\" $NetBSD: install,v 1.5 1999/02/20 16:18:11 scw Exp $ +.\" $NetBSD: install,v 1.6 1999/04/10 16:16:11 scw Exp $ .\" .\" Copyright (c) 1999 The NetBSD Foundation, Inc. .\" All rights reserved. @@ -54,7 +54,9 @@ Create the NetBSD/mvme68k _VER boot tape as described in the section entitled "Preparing a boot tape". Then, with the tape in the drive, type the following at the 1x7Bug prompt: .Pp -.Dl 1x7-Bug\*> Ic bo 5 +.Dl 147-Bug\*> Ic bo 5 +.Pp +.Dl 167-Bug\*> Ic bo 0,50 .Pp As mentioned earlier, this assumes your tape is jumpered for SCSI-id 5. .Pp @@ -80,7 +82,7 @@ Loading: Operating System Volume: NBSD IPL loaded at: $003F0000 -\*>\*> BSD MVME147 tapeboot [$Revision: 1.5 $] +\*>\*> BSD MVME147 tapeboot [$Revision: 1.6 $] 578616+422344+55540+[46032+51284]=0x11a6e4 Start @ 0x8000 ... Copyright (c) 1996, 1997 The NetBSD Foundation, Inc. All rights reserved. @@ -128,7 +130,7 @@ The easiest is loading from tape, which is done as follows: To reboot using the swap partition after running installboot, first use "halt", then at the Bug monitor prompt use a command like: - 147Bug> bo 0,,b: OR 167Bug> bo 0,,,b: + 1x7Bug> bo 0,,b: To view this message again, type: cat /.welcome ssh: @@ -413,7 +415,7 @@ For both boards, the boot messages are very similar: .Pp .Bd -literal -offset indent Start @ 0x8000 ... -\*>\*> BSD MVME147 netboot (via sboot) [$Revision: 1.5 $] +\*>\*> BSD MVME147 netboot (via sboot) [$Revision: 1.6 $] device: le0 attached to 08:00:3e:20:cb:87 boot: client IP address: 192.168.1.4 boot: client name: soapy diff --git a/distrib/notes/mvme68k/prep b/distrib/notes/mvme68k/prep index 185e08865429..226fdb1e664a 100644 --- a/distrib/notes/mvme68k/prep +++ b/distrib/notes/mvme68k/prep @@ -1,4 +1,4 @@ -.\" $NetBSD: prep,v 1.4 1999/02/20 16:18:11 scw Exp $ +.\" $NetBSD: prep,v 1.5 1999/04/10 16:16:11 scw Exp $ . mvme68k machines usually need little or no preparation before installing .Nx "" , @@ -37,16 +37,16 @@ Make sure the RAM size looks ok (if you've got an 8Mb MVME147 or a have the same value as I do). Also make sure the clock is ticking: .Pp .Dl 1x7-Bug\*> Ns Ic time -.Dl Sunday 12/21/29 16:25:14 +.Dl Sunday 12/21/31 16:25:14 .Dl 1x7-Bug\*> Ns Ic time -.Dl Sunday 12/21/29 16:25:15 +.Dl Sunday 12/21/31 16:25:15 .Dl 1x7-Bug\*> .Pp Note that .Nx bases its year at 1968, and adds the year offset in -the MVME1x7's real-time clock to get the current year. So the '29' here -equates to 1997. You may have to adjust your clock using the 'set' +the MVME1x7's real-time clock to get the current year. So the '31' here +equates to 1999. You may have to adjust your clock using the 'set' command to comply with .Nx "" 's requirements. Don't worry if the "Day of the week" is not correct,