New sentence, new line; drop superfluous Pp;
fix Dd argument; use \*[Lt]\*[Gt] instead of <> for HTML output.
This commit is contained in:
parent
ba5400a136
commit
082d3dda1a
|
@ -1,4 +1,4 @@
|
||||||
.\" $NetBSD: dge.4,v 1.2 2004/03/18 20:40:59 wiz Exp $
|
.\" $NetBSD: dge.4,v 1.3 2004/03/18 20:44:25 wiz Exp $
|
||||||
.\"
|
.\"
|
||||||
.\" Copyright (c) 2004, SUNET, Swedish University Computer Network.
|
.\" Copyright (c) 2004, SUNET, Swedish University Computer Network.
|
||||||
.\" All rights reserved.
|
.\" All rights reserved.
|
||||||
|
@ -32,7 +32,7 @@
|
||||||
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
.\" POSSIBILITY OF SUCH DAMAGE.
|
.\" POSSIBILITY OF SUCH DAMAGE.
|
||||||
.\"
|
.\"
|
||||||
.Dd Mars 18, 2004
|
.Dd March 18, 2004
|
||||||
.Dt DGE 4
|
.Dt DGE 4
|
||||||
.Os
|
.Os
|
||||||
.ds nummer "i82597EX
|
.ds nummer "i82597EX
|
||||||
|
@ -54,8 +54,9 @@ which uses a single mode fiber (1310nm) interface.
|
||||||
The
|
The
|
||||||
.nummer
|
.nummer
|
||||||
supports IPv4/TCP/UDP checksumming in hardware, as well
|
supports IPv4/TCP/UDP checksumming in hardware, as well
|
||||||
as TCP Segmentation Offloading (TSO). The driver does currently
|
as TCP Segmentation Offloading (TSO).
|
||||||
only support the hardware checksumming features.
|
The driver does currently only support the hardware checksumming
|
||||||
|
features.
|
||||||
See
|
See
|
||||||
.Xr ifconfig 8
|
.Xr ifconfig 8
|
||||||
for information on how to enable the hardware checksum calculations.
|
for information on how to enable the hardware checksum calculations.
|
||||||
|
@ -66,7 +67,8 @@ link flags
|
||||||
.Ar link0
|
.Ar link0
|
||||||
and
|
and
|
||||||
.Ar link1
|
.Ar link1
|
||||||
to set the PCIX burst size. The burst size is set according to
|
to set the PCIX burst size.
|
||||||
|
The burst size is set according to
|
||||||
this table:
|
this table:
|
||||||
.Pp
|
.Pp
|
||||||
.Bl -column "link0" "link1" "burst size"
|
.Bl -column "link0" "link1" "burst size"
|
||||||
|
@ -84,33 +86,35 @@ the system.
|
||||||
.Bl -diag
|
.Bl -diag
|
||||||
.It dge%d: Tx packet consumes too many DMA segments, dropping...
|
.It dge%d: Tx packet consumes too many DMA segments, dropping...
|
||||||
The packet consisted of too many small mbufs and could therefore
|
The packet consisted of too many small mbufs and could therefore
|
||||||
not be loaded into a DMA map. This is most unlikely, the driver
|
not be loaded into a DMA map.
|
||||||
can currently handle up to 100 segments, but over 80 segments
|
This is most unlikely, the driver can currently handle up to 100
|
||||||
has been seen using large (16k) jumbo frames.
|
segments, but over 80 segments has been seen using large (16k)
|
||||||
|
jumbo frames.
|
||||||
.Pp
|
.Pp
|
||||||
.It dge%s: device timeout (txfree %d txsfree %d txnext %d)
|
.It dge%s: device timeout (txfree %d txsfree %d txnext %d)
|
||||||
The
|
The
|
||||||
.nummer
|
.nummer
|
||||||
had been given packets to send, but didn't interrupt
|
had been given packets to send, but didn't interrupt within 5
|
||||||
within 5 seconds. This diagnostic is most likely the result of
|
seconds.
|
||||||
a hardware failure, and the chip will be reset to resume normal
|
This diagnostic is most likely the result of a hardware failure,
|
||||||
operation.
|
and the chip will be reset to resume normal operation.
|
||||||
.Pp
|
.Pp
|
||||||
.It dge%d: Receive overrun
|
.It dge%d: Receive overrun
|
||||||
If the computer is is heavy loaded the software may not be able to
|
If the computer is is heavy loaded the software may not be able to
|
||||||
keep up removing received datagrams from the receive queue, and
|
keep up removing received datagrams from the receive queue, and
|
||||||
will therefore loose datagrams. To avoid this, check that the other
|
will therefore loose datagrams.
|
||||||
end is using the XON/XOFF protocol, if possible, or increase the
|
To avoid this, check that the other end is using the XON/XOFF
|
||||||
receive descriptor ring size in the driver.
|
protocol, if possible, or increase the receive descriptor ring size
|
||||||
|
in the driver.
|
||||||
.Pp
|
.Pp
|
||||||
.It dge%d: symbol error
|
.It dge%d: symbol error
|
||||||
.It dge%d: parity error
|
.It dge%d: parity error
|
||||||
An error in the XGMII communication was detected. This is a hardware
|
An error in the XGMII communication was detected.
|
||||||
error in the MAC<->PHY communication bus.
|
This is a hardware error in the MAC\*[Lt]-\*[Gt]PHY communication bus.
|
||||||
.Pp
|
.Pp
|
||||||
.It dge%d: CRC error
|
.It dge%d: CRC error
|
||||||
A CRC error in the received datagram was detected. The error is probably
|
A CRC error in the received datagram was detected.
|
||||||
caused in the fiber communication.
|
The error is probably caused in the fiber communication.
|
||||||
.Pp
|
.Pp
|
||||||
.It dge%d: WARNING: reset failed to complete
|
.It dge%d: WARNING: reset failed to complete
|
||||||
This is a fatal error and means that the hardware is broken and
|
This is a fatal error and means that the hardware is broken and
|
||||||
|
@ -118,11 +122,11 @@ will most likely not function correctly.
|
||||||
.Pp
|
.Pp
|
||||||
.It "dge%d: unable to allocate or map rx buffer %d error = %d
|
.It "dge%d: unable to allocate or map rx buffer %d error = %d
|
||||||
The driver was not able to map a mbuf cluster page to a receive
|
The driver was not able to map a mbuf cluster page to a receive
|
||||||
descriptor entry in the receive ring. Most likely the system has
|
descriptor entry in the receive ring.
|
||||||
run out of mbuf clusters or have a too small cluster map. See
|
Most likely the system has run out of mbuf clusters or have a too
|
||||||
the errno for more information.
|
small cluster map.
|
||||||
|
See the errno for more information.
|
||||||
.El
|
.El
|
||||||
.Pp
|
|
||||||
.Sh SEE ALSO
|
.Sh SEE ALSO
|
||||||
.Xr arp 4 ,
|
.Xr arp 4 ,
|
||||||
.Xr ifmedia 4 ,
|
.Xr ifmedia 4 ,
|
||||||
|
|
Loading…
Reference in New Issue