NetBSD/sys/arch/mac68k/dev/ncr5380.c

2049 lines
48 KiB
C
Raw Normal View History

1998-01-12 21:59:04 +03:00
/* $NetBSD: ncr5380.c,v 1.40 1998/01/12 19:22:13 thorpej Exp $ */
/*
* Copyright (c) 1995 Leo Weppelman.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Leo Weppelman.
* 4. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Bit mask of targets you want debugging to be shown
*/
u_char dbg_target_mask = 0x7f;
/*
* Set bit for target when parity checking must be disabled.
* My (LWP) Maxtor 7245S seems to generate parity errors on about 50%
* of all transfers while the data is correct!?
*/
u_char ncr5380_no_parchk = 0xff;
#ifdef AUTO_SENSE
/*
* Bit masks of targets that accept linked commands, and those
* that we've already checked out. Some devices will report
* that they support linked commands when they have problems with
* them. By default, don't try them on any devices. Allow an
* option to override.
*/
u_char ncr_will_link = 0x00;
#ifdef TRY_SCSI_LINKED_COMMANDS
u_char ncr_test_link = ((~TRY_SCSI_LINKED_COMMANDS) & 0x7f);
#else
u_char ncr_test_link = 0x7f;
#endif
#endif /* AUTO_SENSE */
/*
* This is the default sense-command we send.
*/
static u_char sense_cmd[] = {
REQUEST_SENSE, 0, 0, 0, sizeof(struct scsipi_sense_data), 0
};
/*
* True if the main co-routine is running
*/
static volatile int main_running = 0;
/*
* Mask of targets selected
*/
static u_char busy;
static void ncr5380_minphys __P((struct buf *bp));
static int ncr5380_scsi_cmd __P((struct scsipi_xfer *xs));
static void ncr5380_show_scsi_cmd __P((struct scsipi_xfer *xs));
struct scsipi_adapter ncr5380_switch = {
ncr5380_scsi_cmd, /* scsi_cmd() */
ncr5380_minphys, /* scsi_minphys() */
0, /* open_target_lu() */
0 /* close_target_lu() */
};
struct scsipi_device ncr5380_dev = {
NULL, /* use default error handler */
NULL, /* do not have a start functio */
NULL, /* have no async handler */
NULL /* Use default done routine */
};
static SC_REQ req_queue[NREQ];
static SC_REQ *free_head = NULL; /* Free request structures */
/*
* Inline functions:
*/
/*
* Determine the size of a SCSI command.
*/
extern __inline__ int command_size(opcode)
u_char opcode;
{
switch ((opcode >> 4) & 0xf) {
case 0:
case 1:
return (6);
case 2:
case 3:
return (10);
}
return (12);
}
/*
* Wait for request-line to become active. When it doesn't return 0.
* Otherwise return != 0.
* The timeouts in the 'wait_req_*' functions are arbitrary and rather
* large. In 99% of the invocations nearly no timeout is needed but in
* some cases (especially when using my tapedrive, a Tandberg 3600) the
* device is busy internally and the first SCSI-phase will be delayed.
1996-06-23 19:02:58 +04:00
*
* -- A sleeping Fujitsu M2512 is even worse; try 2.5 sec -hf 20 Jun
*/
extern __inline__ int wait_req_true(void)
{
int timeout = 2500000;
while (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_REQ) && --timeout)
delay(1);
return (GET_5380_REG(NCR5380_IDSTAT) & SC_S_REQ);
}
/*
* Wait for request-line to become inactive. When it doesn't return 0.
* Otherwise return != 0.
*/
extern __inline__ int wait_req_false(void)
{
int timeout = 2500000;
while ((GET_5380_REG(NCR5380_IDSTAT) & SC_S_REQ) && --timeout)
delay(1);
return (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_REQ));
}
extern __inline__ void ack_message()
{
SET_5380_REG(NCR5380_ICOM, 0);
}
extern __inline__ void nack_message(SC_REQ *reqp, u_char msg)
{
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
reqp->msgout = msg;
}
extern __inline__ void finish_req(SC_REQ *reqp)
{
int sps;
struct scsipi_xfer *xs = reqp->xs;
#ifdef REAL_DMA
/*
* If we bounced, free the bounce buffer
*/
if (reqp->dr_flag & DRIVER_BOUNCING)
free_bounceb(reqp->bounceb);
#endif /* REAL_DMA */
#ifdef DBG_REQ
if (dbg_target_mask & (1 << reqp->targ_id))
show_request(reqp, "DONE");
#endif
#ifdef DBG_ERR_RET
if (reqp->xs->error != 0)
show_request(reqp, "ERR_RET");
#endif
/*
* Return request to free-q
*/
sps = splbio();
reqp->next = free_head;
free_head = reqp;
splx(sps);
xs->flags |= ITSDONE;
if (!(reqp->dr_flag & DRIVER_LINKCHK))
scsipi_done(xs);
}
/*
* Auto config stuff....
*/
void ncr_attach __P((struct device *, struct device *, void *));
int ncr_match __P((struct device *, struct cfdata *, void *));
/*
* Tricks to make driver-name configurable
*/
#define CFNAME(n) __CONCAT(n,_cd)
#define CANAME(n) __CONCAT(n,_ca)
#define CFSTRING(n) __STRING(n)
struct cfattach CANAME(DRNAME) = {
sizeof(struct ncr_softc), ncr_match, ncr_attach
};
1998-01-12 21:59:04 +03:00
extern struct cfdriver CFNAME(DRNAME);
int
ncr_match(parent, cf, aux)
struct device *parent;
struct cfdata *cf;
void *aux;
{
return (machine_match(parent, cf, aux, &CFNAME(DRNAME)));
}
void
ncr_attach(pdp, dp, auxp)
struct device *pdp, *dp;
void *auxp;
{
struct ncr_softc *sc;
int i;
sc = (struct ncr_softc *)dp;
sc->sc_link.scsipi_scsi.channel = SCSI_CHANNEL_ONLY_ONE;
sc->sc_link.adapter_softc = sc;
sc->sc_link.scsipi_scsi.adapter_target = 7;
sc->sc_link.adapter = &ncr5380_switch;
sc->sc_link.device = &ncr5380_dev;
sc->sc_link.openings = NREQ - 1;
sc->sc_link.scsipi_scsi.max_target = 7;
sc->sc_link.type = BUS_SCSI;
/*
* bitmasks
*/
sc->sc_noselatn = 0;
sc->sc_selected = 0;
/*
* Initialize machine-type specific things...
*/
scsi_mach_init(sc);
1996-10-13 07:21:13 +04:00
printf("\n");
/*
* Initialize request queue freelist.
*/
for (i = 0; i < NREQ; i++) {
req_queue[i].next = free_head;
free_head = &req_queue[i];
}
/*
* Initialize the host adapter
*/
scsi_idisable();
ENABLE_NCR5380(sc);
SET_5380_REG(NCR5380_ICOM, 0);
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_TCOM, 0);
SET_5380_REG(NCR5380_IDSTAT, 0);
scsi_ienable();
/*
* attach all scsi units on us
*/
config_found(dp, &sc->sc_link, scsiprint);
}
/*
* End of auto config stuff....
*/
/*
* Carry out a request from the high level driver.
*/
static int
ncr5380_scsi_cmd(struct scsipi_xfer *xs)
{
int sps;
SC_REQ *reqp, *link, *tmp;
int flags = xs->flags;
/*
* We do not queue RESET commands
*/
if (flags & SCSI_RESET) {
scsi_reset_verbose(xs->sc_link->adapter_softc,
"Got reset-command");
return (COMPLETE);
}
/*
* Get a request block
*/
sps = splbio();
if ((reqp = free_head) == 0) {
splx(sps);
return (TRY_AGAIN_LATER);
}
free_head = reqp->next;
reqp->next = NULL;
splx(sps);
/*
* Initialize our private fields
*/
reqp->dr_flag = (flags & SCSI_POLL) ? DRIVER_NOINT : 0;
reqp->phase = NR_PHASE;
reqp->msgout = MSG_NOOP;
reqp->status = SCSGOOD;
reqp->message = 0xff;
reqp->link = NULL;
reqp->xs = xs;
reqp->targ_id = xs->sc_link->scsipi_scsi.target;
reqp->targ_lun = xs->sc_link->scsipi_scsi.lun;
reqp->xdata_ptr = (u_char*)xs->data;
reqp->xdata_len = xs->datalen;
memcpy(&reqp->xcmd, xs->cmd, sizeof(struct scsi_generic));
reqp->xcmd.bytes[0] |= reqp->targ_lun << 5;
/*
* Sanity check on flags...
*/
if (flags & ITSDONE) {
ncr_tprint(reqp, "scsi_cmd: command already done.....\n");
xs->flags &= ~ITSDONE;
}
if (!(flags & INUSE)) {
ncr_tprint(reqp, "scsi_cmd: command not in use.....\n");
xs->flags |= INUSE;
}
#ifdef REAL_DMA
/*
* Check if DMA can be used on this request
*/
if (scsi_dmaok(reqp))
reqp->dr_flag |= DRIVER_DMAOK;
#endif /* REAL_DMA */
/*
* Insert the command into the issue queue. Note that 'REQUEST SENSE'
* commands are inserted at the head of the queue since any command
* will clear the existing contingent allegience condition and the sense
* data is only valid while the condition exists.
* When possible, link the command to a previous command to the same
* target. This is not very sensible when AUTO_SENSE is not defined!
* Interrupts are disabled while we are fiddling with the issue-queue.
*/
sps = splbio();
link = NULL;
if ((issue_q == NULL) || (reqp->xcmd.opcode == REQUEST_SENSE)) {
reqp->next = issue_q;
issue_q = reqp;
}
else {
tmp = issue_q;
do {
if (!link && (tmp->targ_id == reqp->targ_id) && !tmp->link)
link = tmp;
} while (tmp->next && (tmp = tmp->next));
tmp->next = reqp;
#ifdef AUTO_SENSE
if (link && (ncr_will_link & (1<<reqp->targ_id))) {
link->link = reqp;
link->xcmd.bytes[link->xs->cmdlen-2] |= 1;
}
#endif
}
#ifdef AUTO_SENSE
/*
* If we haven't already, check the target for link support.
* Do this by prefixing the current command with a dummy
* Request_Sense command, link the dummy to the current
* command, and insert the dummy command at the head of the
* issue queue. Set the DRIVER_LINKCHK flag so that we'll
* ignore the results of the dummy command, since we only
* care about whether it was accepted or not.
*/
if (!link && !(ncr_test_link & (1<<reqp->targ_id)) &&
(tmp = free_head) && !(reqp->dr_flag & DRIVER_NOINT)) {
free_head = tmp->next;
tmp->dr_flag = (reqp->dr_flag & ~DRIVER_DMAOK) | DRIVER_LINKCHK;
tmp->phase = NR_PHASE;
tmp->msgout = MSG_NOOP;
tmp->status = SCSGOOD;
tmp->xs = reqp->xs;
tmp->targ_id = reqp->targ_id;
tmp->targ_lun = reqp->targ_lun;
bcopy(sense_cmd, &tmp->xcmd, sizeof(sense_cmd));
tmp->xdata_ptr = (u_char *)&tmp->xs->sense.scsi_sense;
tmp->xdata_len = sizeof(tmp->xs->sense.scsi_sense);
ncr_test_link |= 1<<tmp->targ_id;
tmp->link = reqp;
tmp->xcmd.bytes[sizeof(sense_cmd)-2] |= 1;
tmp->next = issue_q;
issue_q = tmp;
#ifdef DBG_REQ
if (dbg_target_mask & (1 << tmp->targ_id))
show_request(tmp, "LINKCHK");
#endif
}
#endif
splx(sps);
#ifdef DBG_REQ
if (dbg_target_mask & (1 << reqp->targ_id))
show_request(reqp, (reqp->xcmd.opcode == REQUEST_SENSE) ?
"HEAD":"TAIL");
#endif
run_main(xs->sc_link->adapter_softc);
if (xs->flags & (SCSI_POLL|ITSDONE))
return (COMPLETE); /* We're booting or run_main has completed */
return (SUCCESSFULLY_QUEUED);
}
static void
ncr5380_minphys(struct buf *bp)
{
if (bp->b_bcount > MIN_PHYS)
bp->b_bcount = MIN_PHYS;
minphys(bp);
}
#undef MIN_PHYS
static void
ncr5380_show_scsi_cmd(struct scsipi_xfer *xs)
{
u_char *b = (u_char *) xs->cmd;
int i = 0;
if (!(xs->flags & SCSI_RESET)) {
printf("(%d:%d:%d,0x%x)-", xs->sc_link->scsipi_scsi.scsibus,
xs->sc_link->scsipi_scsi.target, xs->sc_link->scsipi_scsi.lun,
xs->sc_link->flags);
while (i < xs->cmdlen) {
if (i)
1996-10-13 07:21:13 +04:00
printf(",");
printf("%x",b[i++]);
}
1996-10-13 07:21:13 +04:00
printf("-\n");
}
else {
1996-10-13 07:21:13 +04:00
printf("(%d:%d:%d)-RESET-\n",
xs->sc_link->scsipi_scsi.scsibus,xs->sc_link->scsipi_scsi.target,
xs->sc_link->scsipi_scsi.lun);
}
}
/*
* The body of the driver.
*/
static void
scsi_main(sc)
struct ncr_softc *sc;
{
SC_REQ *req, *prev;
int itype;
int sps;
/*
* While running in the driver SCSI-interrupts are disabled.
*/
scsi_idisable();
ENABLE_NCR5380(sc);
PID("scsi_main1");
for (;;) {
sps = splbio();
if (!connected) {
/*
* Check if it is fair keep any exclusive access to DMA
* claimed. If not, stop queueing new jobs so the discon_q
* will be eventually drained and DMA can be given up.
*/
if (!fair_to_keep_dma())
goto main_exit;
/*
* Search through the issue-queue for a command
* destined for a target that isn't busy.
*/
prev = NULL;
for (req=issue_q; req != NULL; prev = req, req = req->next) {
if (!(busy & (1 << req->targ_id))) {
/*
* Found one, remove it from the issue queue
*/
if (prev == NULL)
issue_q = req->next;
else prev->next = req->next;
req->next = NULL;
break;
}
}
/*
* When a request has just ended, we get here before an other
* device detects that the bus is free and that it can
* reconnect. The problem is that when this happens, we always
* baffle the device because our (initiator) id is higher. This
* can cause a sort of starvation on slow devices. So we check
* for a pending reselection here.
* Note that 'connected' will be non-null if the reselection
* succeeds.
*/
if ((GET_5380_REG(NCR5380_IDSTAT) & (SC_S_SEL|SC_S_IO))
== (SC_S_SEL|SC_S_IO)){
if (req != NULL) {
req->next = issue_q;
issue_q = req;
}
splx(sps);
reselect(sc);
scsi_clr_ipend();
goto connected;
}
/*
* The host is not connected and there is no request
* pending, exit.
*/
if (req == NULL) {
PID("scsi_main2");
goto main_exit;
}
/*
* Re-enable interrupts before handling the request.
*/
splx(sps);
#ifdef DBG_REQ
if (dbg_target_mask & (1 << req->targ_id))
show_request(req, "TARGET");
#endif
/*
* We found a request. Try to connect to the target. If the
* initiator fails arbitration, the command is put back in the
* issue queue.
*/
if (scsi_select(req, 0)) {
sps = splbio();
req->next = issue_q;
issue_q = req;
splx(sps);
#ifdef DBG_REQ
if (dbg_target_mask & (1 << req->targ_id))
ncr_tprint(req, "Select failed\n");
#endif
}
}
else splx(sps);
connected:
if (connected) {
/*
* If the host is currently connected but a 'real-dma' transfer
* is in progress, the 'end-of-dma' interrupt restarts main.
* So quit.
*/
sps = splbio();
if (connected && (connected->dr_flag & DRIVER_IN_DMA)) {
PID("scsi_main3");
goto main_exit;
}
splx(sps);
/*
* Let the target guide us through the bus-phases
*/
while (information_transfer(sc) == -1)
;
}
}
/* NEVER TO REACH HERE */
panic("ncr5380-SCSI: not designed to come here");
main_exit:
/*
* We enter here with interrupts disabled. We are about to exit main
* so interrupts should be re-enabled. Because interrupts are edge
* triggered, we could already have missed the interrupt. Therefore
* we check the IRQ-line here and re-enter when we really missed a
* valid interrupt.
*/
PID("scsi_main4");
scsi_ienable();
/*
* If we're not currently connected, enable reselection
* interrupts.
*/
if (!connected)
SET_5380_REG(NCR5380_IDSTAT, SC_HOST_ID);
if (scsi_ipending()) {
if ((itype = check_intr(sc)) != INTR_SPURIOUS) {
scsi_idisable();
splx(sps);
if (itype == INTR_RESEL)
reselect(sc);
#ifdef REAL_DMA
else dma_ready();
#else
else {
if (pdma_ready())
goto connected;
panic("Got DMA interrupt without DMA");
}
#endif
scsi_clr_ipend();
goto connected;
}
}
reconsider_dma();
main_running = 0;
splx(sps);
PID("scsi_main5");
}
#ifdef REAL_DMA
/*
* The SCSI-DMA interrupt.
* This interrupt can only be triggered when running in non-polled DMA
* mode. When DMA is not active, it will be silently ignored, it is usually
* to late because the EOP interrupt of the controller happens just a tiny
* bit earlier. It might become usefull when scatter/gather is implemented,
* because in that case only part of the DATAIN/DATAOUT transfer is taken
* out of a single buffer.
*/
static void
ncr_dma_intr(sc)
struct ncr_softc *sc;
{
SC_REQ *reqp;
int dma_done;
PID("ncr_dma_intr");
if ((reqp = connected) && (reqp->dr_flag & DRIVER_IN_DMA)) {
scsi_idisable();
if (!(dma_done = dma_ready())) {
transfer_dma(reqp, reqp->phase, 0);
return;
}
run_main(sc);
}
}
#endif /* REAL_DMA */
/*
* The SCSI-controller interrupt. This interrupt occurs on reselections and
* at the end of non-polled DMA-interrupts. It is assumed to be called from
* the machine-dependent hardware interrupt.
*/
static void
ncr_ctrl_intr(sc)
struct ncr_softc *sc;
{
int itype;
while (scsi_ipending()) {
scsi_idisable();
if ((itype = check_intr(sc)) != INTR_SPURIOUS) {
if (itype == INTR_RESEL)
reselect(sc);
else {
#ifdef REAL_DMA
int dma_done;
if (!(dma_done = dma_ready())) {
transfer_dma(connected, connected->phase, 0);
return;
}
#else
if (pdma_ready())
return;
panic("Got DMA interrupt without DMA\n");
#endif
}
scsi_clr_ipend();
}
run_main(sc);
return;
}
PID("ncr_ctrl_intr1");
}
/*
* Initiate a connection path between the host and the target. The function
* first goes into arbitration for the SCSI-bus. When this succeeds, the target
* is selected and an 'IDENTIFY' message is send.
* Returns -1 when the arbitration failed. Otherwise 0 is returned. When
* the target does not respond (to either selection or 'MESSAGE OUT') the
* 'done' function is executed.
* The result code given by the driver can be influenced by setting 'code'
* to a non-zero value. This is the case when 'select' is called by abort.
*/
static int
scsi_select(reqp, code)
SC_REQ *reqp;
int code;
{
u_char tmp[1];
u_char phase;
u_long cnt;
int sps;
u_int8_t atn_flag;
u_int8_t targ_bit;
struct ncr_softc *sc;
sc = reqp->xs->sc_link->adapter_softc;
DBG_SELPRINT ("Starting arbitration\n", 0);
PID("scsi_select1");
sps = splbio();
/*
* Prevent a race condition here. If a reslection interrupt occurred
* between the decision to pick a new request and the call to select,
* we abort the selection.
* Interrupts are lowered when the 5380 is setup to arbitrate for the
* bus.
*/
if (connected) {
splx(sps);
PID("scsi_select2");
return (-1);
}
/*
* Set phase bits to 0, otherwise the 5380 won't drive the bus during
* selection.
*/
SET_5380_REG(NCR5380_TCOM, 0);
SET_5380_REG(NCR5380_ICOM, 0);
/*
* Arbitrate for the bus.
*/
SET_5380_REG(NCR5380_DATA, SC_HOST_ID);
SET_5380_REG(NCR5380_MODE, SC_ARBIT);
splx(sps);
cnt = 10;
while (!(GET_5380_REG(NCR5380_ICOM) & SC_AIP) && --cnt)
delay(1);
if (!(GET_5380_REG(NCR5380_ICOM) & SC_AIP)) {
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
DBG_SELPRINT ("Arbitration lost, bus not free\n",0);
PID("scsi_select3");
return (-1);
}
/* The arbitration delay is 2.2 usecs */
delay(3);
/*
* Check the result of the arbitration. If we failed, return -1.
*/
if (GET_5380_REG(NCR5380_ICOM) & SC_LA) {
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
PID("scsi_select4");
return (-1);
}
/*
* The spec requires that we should read the data register to
* check for higher id's and check the SC_LA again.
*/
tmp[0] = GET_5380_REG(NCR5380_DATA);
if (tmp[0] & ~((SC_HOST_ID << 1) - 1)) {
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
DBG_SELPRINT ("Arbitration lost, higher id present\n",0);
PID("scsi_select5");
return (-1);
}
if (GET_5380_REG(NCR5380_ICOM) & SC_LA) {
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
DBG_SELPRINT ("Arbitration lost,deassert SC_ARBIT\n",0);
PID("scsi_select6");
return (-1);
}
SET_5380_REG(NCR5380_ICOM, SC_A_SEL | SC_A_BSY);
if (GET_5380_REG(NCR5380_ICOM) & SC_LA) {
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
DBG_SELPRINT ("Arbitration lost, deassert SC_A_SEL\n", 0);
PID("scsi_select7");
return (-1);
}
/* Bus settle delay + Bus clear delay = 1.2 usecs */
delay(2);
DBG_SELPRINT ("Arbitration complete\n", 0);
/*
* Now that we won the arbitration, start the selection.
*/
targ_bit = 1 << reqp->targ_id;
SET_5380_REG(NCR5380_DATA, SC_HOST_ID | targ_bit);
if (sc->sc_noselatn & targ_bit)
atn_flag = 0;
else
atn_flag = SC_A_ATN;
/*
* Raise ATN while SEL is true before BSY goes false from arbitration,
* since this is the only way to guarantee that we'll get a MESSAGE OUT
* phase immediately after the selection.
*/
SET_5380_REG(NCR5380_ICOM, SC_A_BSY | SC_A_SEL | atn_flag | SC_ADTB);
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
/*
* Turn off reselection interrupts
*/
SET_5380_REG(NCR5380_IDSTAT, 0);
/*
* Reset BSY. The delay following it, surpresses a glitch in the
* 5380 which causes us to see our own BSY signal instead of that of
* the target.
*/
SET_5380_REG(NCR5380_ICOM, SC_A_SEL | atn_flag | SC_ADTB);
delay(1);
/*
* Wait for the target to react, the specs call for a timeout of
* 250 ms.
*/
cnt = 25000;
while (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY) && --cnt)
delay(10);
if (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY)) {
/*
* There is no reaction from the target, start the selection
* timeout procedure. We release the databus but keep SEL
* asserted. After that we wait a 'selection abort time' (200
* usecs) and 2 deskew delays (90 ns) and check BSY again.
* When BSY is asserted, we assume the selection succeeded,
* otherwise we release the bus.
*/
SET_5380_REG(NCR5380_ICOM, SC_A_SEL | atn_flag);
delay(201);
if (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY)) {
SET_5380_REG(NCR5380_ICOM, 0);
reqp->xs->error = code ? code : XS_SELTIMEOUT;
DBG_SELPRINT ("Target %d not responding to sel\n",
reqp->targ_id);
if (reqp->dr_flag & DRIVER_LINKCHK)
ncr_test_link &= ~(1<<reqp->targ_id);
finish_req(reqp);
PID("scsi_select8");
return (0);
}
}
SET_5380_REG(NCR5380_ICOM, atn_flag);
DBG_SELPRINT ("Target %d responding to select.\n", reqp->targ_id);
/*
* The SCSI-interrupts are disabled while a request is being handled.
*/
scsi_idisable();
/*
* If we did not request ATN, then don't try to send IDENTIFY.
*/
if (atn_flag == 0) {
reqp->phase = PH_CMD;
goto identify_failed;
}
/*
* Here we prepare to send an 'IDENTIFY' message.
* Allow disconnect only when interrups are allowed.
*/
tmp[0] = MSG_IDENTIFY(reqp->targ_lun,
(reqp->dr_flag & DRIVER_NOINT) ? 0 : 1);
cnt = 1;
phase = PH_MSGOUT;
/*
* Since we followed the SCSI-spec and raised ATN while SEL was true
* but before BSY was false during the selection, a 'MESSAGE OUT'
* phase should follow. Unfortunately, this does not happen on
* all targets (Asante ethernet devices, for example), so we must
* check the actual mode if the message transfer fails--if the
* new phase is PH_CMD and has never been successfully selected
* w/ATN in the past, then we assume that it is an old device
* that doesn't support select w/ATN.
*/
if (transfer_pio(&phase, tmp, &cnt, 0) || cnt) {
if ((phase == PH_CMD) && !(sc->sc_selected & targ_bit)) {
DBG_SELPRINT ("Target %d: not responding to ATN.\n",
reqp->targ_id);
sc->sc_noselatn |= targ_bit;
reqp->phase = PH_CMD;
goto identify_failed;
}
DBG_SELPRINT ("Target %d: failed to send identify\n",
reqp->targ_id);
/*
* Try to disconnect from the target. We cannot leave
* it just hanging here.
*/
if (!reach_msg_out(sc, sizeof(struct scsi_generic))) {
u_long len = 1;
u_char phase = PH_MSGOUT;
u_char msg = MSG_ABORT;
transfer_pio(&phase, &msg, &len, 0);
}
else scsi_reset_verbose(sc, "Connected to unidentified target");
SET_5380_REG(NCR5380_ICOM, 0);
reqp->xs->error = code ? code : XS_DRIVER_STUFFUP;
finish_req(reqp);
PID("scsi_select9");
return (0);
}
reqp->phase = PH_MSGOUT;
identify_failed:
sc->sc_selected |= targ_bit;
#ifdef notyet /* LWP: Do we need timeouts in the driver? */
/*
* Command is connected, start timer ticking.
*/
ccb_p->xtimeout = ccb_p->timeout + Lbolt;
#endif
connected = reqp;
busy |= targ_bit;
PID("scsi_select10");
return (0);
}
/*
* Return codes:
* 0: Job has finished or disconnected, find something else
* -1: keep on calling information_transfer() from scsi_main()
*/
static int
information_transfer(sc)
struct ncr_softc *sc;
{
SC_REQ *reqp = connected;
u_char tmp, phase;
u_long len;
PID("info_transf1");
/*
* Clear pending interrupts from 5380-chip.
*/
scsi_clr_ipend();
/*
* The SCSI-spec requires BSY to be true while connected to a target,
* loosing it means we lost the target...
* Also REQ needs to be asserted here to indicate that the bus-phase
* is valid. When the target does not supply REQ within a 'reasonable'
* amount of time, it's probably lost in it's own maze of twisting
* passages, we have to reset the bus to free it.
*/
if (GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY)
wait_req_true();
tmp = GET_5380_REG(NCR5380_IDSTAT);
if ((tmp & (SC_S_BSY|SC_S_REQ)) != (SC_S_BSY|SC_S_REQ)) {
busy &= ~(1 << reqp->targ_id);
connected = NULL;
reqp->xs->error = XS_TIMEOUT;
finish_req(reqp);
if (!(tmp & SC_S_REQ))
scsi_reset_verbose(sc,
"Timeout waiting for phase-change");
PID("info_transf2");
return (0);
}
phase = (tmp >> 2) & 7;
if (phase != reqp->phase) {
reqp->phase = phase;
DBG_INFPRINT(show_phase, reqp, phase);
}
else {
/*
* Same data-phase. If same error give up
*/
if ((reqp->msgout == MSG_ABORT)
&& ((phase == PH_DATAOUT) || (phase == PH_DATAIN))) {
busy &= ~(1 << reqp->targ_id);
connected = NULL;
finish_req(reqp);
scsi_reset_verbose(sc, "Failure to abort command");
return (0);
}
}
switch (phase) {
case PH_DATAOUT:
#ifdef DBG_NOWRITE
ncr_tprint(reqp, "NOWRITE set -- write attempt aborted.");
reqp->msgout = MSG_ABORT;
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
return (-1);
#endif /* DBG_NOWRITE */
/*
* If this is the first write using DMA, fill
* the bounce buffer.
*/
if (reqp->xdata_ptr == reqp->xs->data) { /* XXX */
if (reqp->dr_flag & DRIVER_BOUNCING)
bcopy(reqp->xdata_ptr, reqp->bounceb, reqp->xdata_len);
}
case PH_DATAIN:
if (reqp->xdata_len <= 0) {
/*
* Target keeps requesting data. Try to get into
* message-out phase by feeding/taking 100 byte.
*/
ncr_tprint(reqp, "Target requests too much data\n");
reqp->msgout = MSG_ABORT;
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
reach_msg_out(sc, 100);
return (-1);
}
#ifdef REAL_DMA
if (reqp->dr_flag & DRIVER_DMAOK) {
int poll = REAL_DMA_POLL|(reqp->dr_flag & DRIVER_NOINT);
transfer_dma(reqp, phase, poll);
if (!poll)
return (0);
}
else
#endif
{
PID("info_transf3");
len = reqp->xdata_len;
#ifdef USE_PDMA
if (transfer_pdma(&phase, reqp->xdata_ptr, &len) == 0)
return (0);
#else
transfer_pio(&phase, reqp->xdata_ptr, &len, 0);
#endif
reqp->xdata_ptr += reqp->xdata_len - len;
reqp->xdata_len = len;
}
return (-1);
case PH_MSGIN:
/*
* We only expect single byte messages here.
*/
len = 1;
transfer_pio(&phase, &tmp, &len, 1);
reqp->message = tmp;
return (handle_message(reqp, tmp));
case PH_MSGOUT:
len = 1;
transfer_pio(&phase, &reqp->msgout, &len, 0);
if (reqp->msgout == MSG_ABORT) {
busy &= ~(1 << reqp->targ_id);
connected = NULL;
if (!reqp->xs->error)
reqp->xs->error = XS_DRIVER_STUFFUP;
finish_req(reqp);
PID("info_transf4");
return (0);
}
reqp->msgout = MSG_NOOP;
return (-1);
case PH_CMD :
len = command_size(reqp->xcmd.opcode);
transfer_pio(&phase, (u_char *)&reqp->xcmd, &len, 0);
PID("info_transf5");
return (-1);
case PH_STATUS:
len = 1;
transfer_pio(&phase, &tmp, &len, 0);
reqp->status = tmp;
PID("info_transf6");
return (-1);
default :
ncr_tprint(reqp, "Unknown phase\n");
}
PID("info_transf7");
return (-1);
}
/*
* Handle the message 'msg' send to us by the target.
* Return values:
* 0 : The current command has completed.
* -1 : Get on to the next phase.
*/
static int
handle_message(reqp, msg)
SC_REQ *reqp;
u_int msg;
{
int sps;
SC_REQ *prev, *req;
PID("hmessage1");
switch (msg) {
/*
* Linking lets us reduce the time required to get
* the next command to the device, skipping the arbitration
* and selection time. In the current implementation,
* we merely have to start the next command pointed
* to by 'next_link'.
*/
case MSG_LINK_CMD_COMPLETE:
case MSG_LINK_CMD_COMPLETEF:
if (reqp->link == NULL) {
ncr_tprint(reqp, "No link for linked command");
nack_message(reqp, MSG_ABORT);
PID("hmessage2");
return (-1);
}
ack_message();
if (!(reqp->dr_flag & DRIVER_AUTOSEN)) {
reqp->xs->resid = reqp->xdata_len;
reqp->xs->error = 0;
}
#ifdef AUTO_SENSE
if (check_autosense(reqp, 1) == -1)
return (-1);
#endif /* AUTO_SENSE */
#ifdef DBG_REQ
if (dbg_target_mask & (1 << reqp->targ_id))
show_request(reqp->link, "LINK");
#endif
connected = reqp->link;
/*
* Unlink the 'linked' request from the issue_q
*/
sps = splbio();
prev = NULL;
req = issue_q;
for (; req != NULL; prev = req, req = req->next) {
if (req == connected)
break;
}
if (req == NULL)
panic("Inconsistent issue_q");
if (prev == NULL)
issue_q = req->next;
else prev->next = req->next;
req->next = NULL;
splx(sps);
finish_req(reqp);
PID("hmessage3");
return (-1);
case MSG_ABORT:
case MSG_CMDCOMPLETE:
ack_message();
connected = NULL;
busy &= ~(1 << reqp->targ_id);
if (!(reqp->dr_flag & DRIVER_AUTOSEN)) {
reqp->xs->resid = reqp->xdata_len;
reqp->xs->error = 0;
}
#ifdef AUTO_SENSE
if (check_autosense(reqp, 0) == -1) {
PID("hmessage4");
return (0);
}
#endif /* AUTO_SENSE */
finish_req(reqp);
PID("hmessage5");
return (0);
case MSG_MESSAGE_REJECT:
ack_message();
PID("hmessage6");
return (-1);
case MSG_DISCONNECT:
ack_message();
#ifdef DBG_REQ
if (dbg_target_mask & (1 << reqp->targ_id))
show_request(reqp, "DISCON");
#endif
sps = splbio();
connected = NULL;
reqp->next = discon_q;
discon_q = reqp;
splx(sps);
PID("hmessage7");
return (0);
case MSG_SAVEDATAPOINTER:
case MSG_RESTOREPOINTERS:
/*
* We save pointers implicitely at disconnect.
* So we can ignore these messages.
*/
ack_message();
PID("hmessage8");
return (-1);
case MSG_EXTENDED:
nack_message(reqp, MSG_MESSAGE_REJECT);
PID("hmessage9");
return (-1);
default:
1996-03-07 23:47:01 +03:00
if ((msg & 0x80) && !(msg & 0x18)) { /* IDENTIFY */
PID("hmessage10");
ack_message();
return (0);
} else {
ncr_tprint(reqp,
"Unknown message %x. Rejecting.\n",
msg);
nack_message(reqp, MSG_MESSAGE_REJECT);
}
return (-1);
}
PID("hmessage11");
return (-1);
}
/*
* Handle reselection. If a valid reconnection occurs, connected
* points at the reconnected command. The command is removed from the
* disconnected queue.
*/
static void
reselect(sc)
struct ncr_softc *sc;
{
u_char phase;
u_long len;
u_char msg;
u_char target_mask;
int abort = 0;
SC_REQ *tmp, *prev;
PID("reselect1");
target_mask = GET_5380_REG(NCR5380_DATA) & ~SC_HOST_ID;
/*
* At this point, we have detected that our SCSI-id is on the bus,
* SEL is true and BSY was false for at least one bus settle
* delay (400 ns.).
* We must assert BSY ourselves, until the target drops the SEL signal.
* The SCSI-spec specifies no maximum time for this, so we have to
* choose something long enough to suit all targets.
*/
SET_5380_REG(NCR5380_ICOM, SC_A_BSY);
len = 250000;
while ((GET_5380_REG(NCR5380_IDSTAT) & SC_S_SEL) && (len > 0)) {
delay(1);
len--;
}
if (GET_5380_REG(NCR5380_IDSTAT) & SC_S_SEL) {
/* Damn SEL isn't dropping */
scsi_reset_verbose(sc, "Target won't drop SEL during Reselect");
return;
}
SET_5380_REG(NCR5380_ICOM, 0);
/*
* Check if the reselection is still valid. Check twice because
* of possible line glitches - cheaper than delay(1) and we need
* only a few nanoseconds.
*/
if (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY)) {
if (!(GET_5380_REG(NCR5380_IDSTAT) & SC_S_BSY)) {
ncr_aprint(sc, "Stepped into the reselection timeout\n");
return;
}
}
/*
* Get the expected identify message.
*/
phase = PH_MSGIN;
len = 1;
transfer_pio(&phase, &msg, &len, 0);
if (len || !MSG_ISIDENTIFY(msg)) {
ncr_aprint(sc, "Expecting IDENTIFY, got 0x%x\n", msg);
abort = 1;
tmp = NULL;
}
else {
/*
* Find the command reconnecting
*/
for (tmp = discon_q, prev = NULL; tmp; prev = tmp, tmp = tmp->next){
if (target_mask == (1 << tmp->targ_id)) {
if (prev)
prev->next = tmp->next;
else discon_q = tmp->next;
tmp->next = NULL;
break;
}
}
if (tmp == NULL) {
ncr_aprint(sc, "No disconnected job for targetmask %x\n",
target_mask);
abort = 1;
}
}
if (abort) {
msg = MSG_ABORT;
len = 1;
phase = PH_MSGOUT;
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
if (transfer_pio(&phase, &msg, &len, 0) || len)
scsi_reset_verbose(sc, "Failure to abort reselection");
}
else {
connected = tmp;
#ifdef DBG_REQ
if (dbg_target_mask & (1 << tmp->targ_id))
show_request(tmp, "RECON");
#endif
}
PID("reselect2");
}
/*
* Transfer data in a given phase using programmed I/O.
* Returns -1 when a different phase is entered without transferring the
* maximum number of bytes, 0 if all bytes transferred or exit is in the same
* phase.
*/
static int
transfer_pio(phase, data, len, dont_drop_ack)
u_char *phase;
u_char *data;
u_long *len;
int dont_drop_ack;
{
u_int cnt = *len;
u_char ph = *phase;
u_char tmp, new_icom;
DBG_PIOPRINT ("SCSI: transfer_pio start: phase: %d, len: %d\n", ph,cnt);
PID("tpio1");
SET_5380_REG(NCR5380_TCOM, ph);
do {
if (!wait_req_true()) {
DBG_PIOPRINT ("SCSI: transfer_pio: missing REQ\n", 0, 0);
break;
}
if (((GET_5380_REG(NCR5380_IDSTAT) >> 2) & 7) != ph) {
DBG_PIOPRINT ("SCSI: transfer_pio: phase mismatch\n", 0, 0);
break;
}
if (PH_IN(ph)) {
*data++ = GET_5380_REG(NCR5380_DATA);
SET_5380_REG(NCR5380_ICOM, SC_A_ACK);
if ((cnt == 1) && dont_drop_ack)
new_icom = SC_A_ACK;
else new_icom = 0;
}
else {
SET_5380_REG(NCR5380_DATA, *data++);
/*
* The SCSI-standard suggests that in the 'MESSAGE OUT' phase,
* the initiator should drop ATN on the last byte of the
* message phase after REQ has been asserted for the handshake
* but before the initiator raises ACK.
*/
if (!( (ph == PH_MSGOUT) && (cnt > 1) )) {
SET_5380_REG(NCR5380_ICOM, SC_ADTB);
SET_5380_REG(NCR5380_ICOM, SC_ADTB | SC_A_ACK);
new_icom = 0;
}
else {
SET_5380_REG(NCR5380_ICOM, SC_ADTB | SC_A_ATN);
SET_5380_REG(NCR5380_ICOM, SC_ADTB|SC_A_ATN|SC_A_ACK);
new_icom = SC_A_ATN;
}
}
if (!wait_req_false()) {
DBG_PIOPRINT ("SCSI: transfer_pio - REQ not dropping\n", 0, 0);
break;
}
SET_5380_REG(NCR5380_ICOM, new_icom);
} while (--cnt);
if ((tmp = GET_5380_REG(NCR5380_IDSTAT)) & SC_S_REQ)
*phase = (tmp >> 2) & 7;
else *phase = NR_PHASE;
*len = cnt;
DBG_PIOPRINT ("SCSI: transfer_pio done: phase: %d, len: %d\n",
*phase, cnt);
PID("tpio2");
if (!cnt || (*phase == ph))
return (0);
return (-1);
}
#ifdef REAL_DMA
/*
* Start a DMA-transfer on the device using the current pointers.
* If 'poll' is true, the function busy-waits until DMA has completed.
*/
static void
transfer_dma(reqp, phase, poll)
SC_REQ *reqp;
u_int phase;
int poll;
{
int dma_done;
u_char mbase = 0;
int sps;
again:
PID("tdma1");
/*
* We should be in phase, otherwise we are not allowed to
* drive the bus.
*/
SET_5380_REG(NCR5380_TCOM, phase);
/*
* Defer interrupts until DMA is fully running.
*/
sps = splbio();
/*
* Clear pending interrupts and parity errors.
*/
scsi_clr_ipend();
if (!poll) {
/*
* Enable SCSI interrupts and set IN_DMA flag, set 'mbase'
* to the interrupts we want enabled.
*/
scsi_ienable();
reqp->dr_flag |= DRIVER_IN_DMA;
mbase = SC_E_EOPI | SC_MON_BSY;
}
else scsi_idisable();
mbase |= IMODE_BASE | SC_M_DMA;
scsi_dma_setup(reqp, phase, mbase);
splx(sps);
if (poll) {
/*
* On polled-dma transfers, we wait here until the
* 'end-of-dma' condition occurs.
*/
poll_edma(reqp);
if (!(dma_done = dma_ready()))
goto again;
}
PID("tdma2");
}
/*
* Check results of a DMA data-transfer.
*/
static int
dma_ready()
{
SC_REQ *reqp = connected;
int dmstat, is_edma;
long bytes_left, bytes_done;
is_edma = get_dma_result(reqp, &bytes_left);
dmstat = GET_5380_REG(NCR5380_DMSTAT);
/*
* Check if the call is sensible and not caused by any spurious
* interrupt.
*/
if (!is_edma && !(dmstat & (SC_END_DMA|SC_BSY_ERR))
&& (dmstat & SC_PHS_MTCH) ) {
ncr_tprint(reqp, "dma_ready: spurious call "
"(dm:%x,last_hit: %s)\n",
#ifdef DBG_PID
dmstat, last_hit[DBG_PID-1]);
#else
dmstat, "unknown");
#endif
return (0);
}
/*
* Clear all (pending) interrupts.
*/
scsi_clr_ipend();
/*
* Update various transfer-pointers/lengths
*/
bytes_done = reqp->dm_cur->dm_count - bytes_left;
if ((reqp->dr_flag & DRIVER_BOUNCING) && (PH_IN(reqp->phase))) {
/*
* Copy the bytes read until now from the bounce buffer
* to the 'real' destination. Flush the data-cache
* before copying.
*/
PCIA();
bcopy(reqp->bouncerp, reqp->xdata_ptr, bytes_done);
reqp->bouncerp += bytes_done;
}
reqp->xdata_ptr = &reqp->xdata_ptr[bytes_done]; /* XXX */
reqp->xdata_len -= bytes_done; /* XXX */
if ((reqp->dm_cur->dm_count -= bytes_done) == 0)
reqp->dm_cur++;
else reqp->dm_cur->dm_addr += bytes_done;
if (PH_IN(reqp->phase) && (dmstat & SC_PAR_ERR)) {
if (!(ncr5380_no_parchk & (1 << reqp->targ_id))) {
ncr_tprint(reqp, "parity error in data-phase\n");
reqp->xs->error = XS_TIMEOUT;
}
}
/*
* DMA mode should always be reset even when we will continue with the
* next chain. It is also essential to clear the MON_BUSY because
* when LOST_BUSY is unexpectedly set, we will not be able to drive
* the bus....
*/
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
if ((dmstat & SC_BSY_ERR) || !(dmstat & SC_PHS_MTCH)
|| (reqp->dm_cur > reqp->dm_last) || (reqp->xs->error)) {
/*
* Tell interrupt functions DMA mode has ended.
*/
reqp->dr_flag &= ~DRIVER_IN_DMA;
/*
* Clear mode and icom
*/
SET_5380_REG(NCR5380_MODE, IMODE_BASE);
SET_5380_REG(NCR5380_ICOM, 0);
if (dmstat & SC_BSY_ERR) {
if (!reqp->xs->error)
reqp->xs->error = XS_TIMEOUT;
finish_req(reqp);
PID("dma_ready1");
return (1);
}
if (reqp->xs->error != 0) {
ncr_tprint(reqp, "dma-ready: code = %d\n", reqp->xs->error); /* LWP */
reqp->msgout = MSG_ABORT;
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
}
PID("dma_ready2");
return (1);
}
return (0);
}
#endif /* REAL_DMA */
static int
check_autosense(reqp, linked)
SC_REQ *reqp;
int linked;
{
int sps;
/*
* If this is the driver's Link Check for this target, ignore
* the results of the command. All we care about is whether we
* got here from a LINK_CMD_COMPLETE or CMD_COMPLETE message.
*/
PID("linkcheck");
if (reqp->dr_flag & DRIVER_LINKCHK) {
if (linked)
ncr_will_link |= 1<<reqp->targ_id;
else ncr_tprint(reqp, "Does not support linked commands\n");
return (0);
}
/*
* If we not executing an auto-sense and the status code
* is request-sense, we automatically issue a request
* sense command.
*/
PID("cautos1");
if (!(reqp->dr_flag & DRIVER_AUTOSEN)) {
switch (reqp->status & SCSMASK) {
case SCSCHKC:
bcopy(sense_cmd, &reqp->xcmd, sizeof(sense_cmd));
reqp->xdata_ptr = (u_char *)&reqp->xs->sense.scsi_sense;
reqp->xdata_len = sizeof(reqp->xs->sense.scsi_sense);
reqp->dr_flag |= DRIVER_AUTOSEN;
reqp->dr_flag &= ~DRIVER_DMAOK;
if (!linked) {
sps = splbio();
reqp->next = issue_q;
issue_q = reqp;
splx(sps);
}
else reqp->xcmd.bytes[sizeof(sense_cmd)-2] |= 1;
#ifdef DBG_REQ
bzero(reqp->xdata_ptr, reqp->xdata_len);
if (dbg_target_mask & (1 << reqp->targ_id))
show_request(reqp, "AUTO-SENSE");
#endif
PID("cautos2");
return (-1);
case SCSBUSY:
reqp->xs->error = XS_BUSY;
return (0);
}
}
else {
/*
* An auto-sense has finished
*/
if ((reqp->status & SCSMASK) != SCSGOOD)
reqp->xs->error = XS_DRIVER_STUFFUP; /* SC_E_AUTOSEN; */
else reqp->xs->error = XS_SENSE;
reqp->status = SCSCHKC;
}
PID("cautos3");
return (0);
}
static int
reach_msg_out(sc, len)
struct ncr_softc *sc;
u_long len;
{
u_char phase;
u_char data;
u_long n = len;
ncr_aprint(sc, "Trying to reach Message-out phase\n");
if ((phase = GET_5380_REG(NCR5380_IDSTAT)) & SC_S_REQ)
phase = (phase >> 2) & 7;
else return (-1);
ncr_aprint(sc, "Trying to reach Message-out phase, now: %d\n", phase);
if (phase == PH_MSGOUT)
return (0);
SET_5380_REG(NCR5380_TCOM, phase);
do {
if (!wait_req_true())
break;
if (((GET_5380_REG(NCR5380_IDSTAT) >> 2) & 7) != phase)
break;
if (PH_IN(phase)) {
data = GET_5380_REG(NCR5380_DATA);
SET_5380_REG(NCR5380_ICOM, SC_A_ACK | SC_A_ATN);
}
else {
SET_5380_REG(NCR5380_DATA, 0);
SET_5380_REG(NCR5380_ICOM, SC_ADTB|SC_A_ACK|SC_A_ATN);
}
if (!wait_req_false())
break;
SET_5380_REG(NCR5380_ICOM, SC_A_ATN);
} while (--n);
if ((phase = GET_5380_REG(NCR5380_IDSTAT)) & SC_S_REQ) {
phase = (phase >> 2) & 7;
if (phase == PH_MSGOUT) {
ncr_aprint(sc, "Message-out phase reached after "
"%ld bytes.\n", len - n);
return (0);
}
}
return (-1);
}
void
scsi_reset()
{
SC_REQ *tmp, *next;
int sps;
PID("scsi_reset1");
sps = splbio();
SET_5380_REG(NCR5380_ICOM, SC_A_RST);
delay(100);
SET_5380_REG(NCR5380_ICOM, 0);
scsi_clr_ipend();
/*
* None of the jobs in the discon_q will ever be reconnected,
* notify this to the higher level code.
*/
for (tmp = discon_q; tmp ;) {
next = tmp->next;
tmp->next = NULL;
tmp->xs->error = XS_TIMEOUT;
busy &= ~(1 << tmp->targ_id);
finish_req(tmp);
tmp = next;
}
discon_q = NULL;
/*
* The current job will never finish either.
* The problem is that we can't finish the job because an instance
* of main is running on it. Our best guess is that the job is currently
* doing REAL-DMA. In that case 'dma_ready()' should correctly finish
* the job because it detects BSY-loss.
*/
if ((tmp = connected) != NULL) {
if (tmp->dr_flag & DRIVER_IN_DMA) {
tmp->xs->error = XS_DRIVER_STUFFUP;
#ifdef REAL_DMA
dma_ready();
#endif
}
}
splx(sps);
PID("scsi_reset2");
/*
* Give the attached devices some time to handle the reset. This
* value is arbitrary but should be relatively long.
*/
delay(100000);
}
static void
scsi_reset_verbose(sc, why)
struct ncr_softc *sc;
const char *why;
{
ncr_aprint(sc, "Resetting SCSI-bus (%s)\n", why);
scsi_reset();
}
/*
* Check validity of the IRQ set by the 5380. If the interrupt is valid,
* the appropriate action is carried out (reselection or DMA ready) and
* INTR_RESEL or INTR_DMA is returned. Otherwise a console notice is written
* and INTR_SPURIOUS is returned.
*/
static int
check_intr(sc)
struct ncr_softc *sc;
{
SC_REQ *reqp;
if ((GET_5380_REG(NCR5380_IDSTAT) & (SC_S_SEL|SC_S_IO))
==(SC_S_SEL|SC_S_IO))
return (INTR_RESEL);
else {
if ((reqp = connected) && (reqp->dr_flag & DRIVER_IN_DMA)){
reqp->dr_flag &= ~DRIVER_IN_DMA;
return (INTR_DMA);
}
}
scsi_clr_ipend();
1996-10-13 07:21:13 +04:00
printf("-->");
scsi_show();
ncr_aprint(sc, "Spurious interrupt.\n");
return (INTR_SPURIOUS);
}
#ifdef REAL_DMA
/*
* Check if DMA can be used for this request. This function also builds
* the dma-chain.
*/
static int
scsi_dmaok(reqp)
SC_REQ *reqp;
{
u_long phy_buf;
u_long phy_len;
void *req_addr;
u_long req_len;
struct dma_chain *dm;
/*
* Initialize locals and requests' DMA-chain.
*/
req_len = reqp->xdata_len;
req_addr = (void*)reqp->xdata_ptr;
dm = reqp->dm_cur = reqp->dm_last = reqp->dm_chain;
dm->dm_count = dm->dm_addr = 0;
reqp->dr_flag &= ~DRIVER_BOUNCING;
/*
* Do not accept zero length DMA.
*/
if (req_len == 0)
return (0);
/*
* LWP: I think that this restriction is not strictly nessecary.
*/
if ((req_len & 0x1) || ((u_int)req_addr & 0x3))
return (0);
/*
* Build the DMA-chain.
*/
dm->dm_addr = phy_buf = kvtop(req_addr);
while (req_len) {
if (req_len < (phy_len = NBPG - ((u_long)req_addr & PGOFSET)))
phy_len = req_len;
req_addr += phy_len;
req_len -= phy_len;
dm->dm_count += phy_len;
if (req_len) {
u_long tmp = kvtop(req_addr);
if ((phy_buf + phy_len) != tmp) {
if (wrong_dma_range(reqp, dm)) {
if (reqp->dr_flag & DRIVER_BOUNCING)
goto bounceit;
return (0);
}
if (++dm >= &reqp->dm_chain[MAXDMAIO]) {
ncr_tprint(reqp,"dmaok: DMA chain too long!\n");
return (0);
}
dm->dm_count = 0;
dm->dm_addr = tmp;
}
phy_buf = tmp;
}
}
if (wrong_dma_range(reqp, dm)) {
if (reqp->dr_flag & DRIVER_BOUNCING)
goto bounceit;
return (0);
}
reqp->dm_last = dm;
return (1);
bounceit:
if ((reqp->bounceb = alloc_bounceb(reqp->xdata_len)) == NULL) {
/*
* If we can't get a bounce buffer, forget DMA
*/
reqp->dr_flag &= ~DRIVER_BOUNCING;
return(0);
}
/*
* Initialize a single DMA-range containing the bounced request
*/
dm = reqp->dm_cur = reqp->dm_last = reqp->dm_chain;
dm->dm_addr = kvtop(reqp->bounceb);
dm->dm_count = reqp->xdata_len;
reqp->bouncerp = reqp->bounceb;
return (1);
}
#endif /* REAL_DMA */
static void
run_main(sc)
struct ncr_softc *sc;
{
int sps = splbio();
if (!main_running) {
/*
* If shared resources are required, claim them
* before entering 'scsi_main'. If we can't get them
* now, assume 'run_main' will be called when the resource
* becomes available.
*/
if (!claimed_dma()) {
splx(sps);
return;
}
main_running = 1;
splx(sps);
scsi_main(sc);
}
else splx(sps);
}
/*
* Prefix message with full target info.
*/
static void
ncr_tprint(SC_REQ *reqp, char *fmt, ...)
{
va_list ap;
va_start(ap, fmt);
scsi_print_addr(reqp->xs->sc_link);
1996-10-13 07:21:13 +04:00
printf("%:", fmt, ap);
va_end(ap);
}
/*
* Prefix message with adapter info.
*/
static void
ncr_aprint(struct ncr_softc *sc, char *fmt, ...)
{
va_list ap;
va_start(ap, fmt);
1996-10-13 07:21:13 +04:00
printf("%s: %:", sc->sc_dev.dv_xname, fmt, ap);
va_end(ap);
}
/****************************************************************************
* Start Debugging Functions *
****************************************************************************/
static void
show_data_sense(xs)
struct scsipi_xfer *xs;
{
u_char *p1, *p2;
int i;
int sz;
p1 = (u_char *) xs->cmd;
p2 = (u_char *)&xs->sense.scsi_sense;
if(*p2 == 0)
return; /* No(n)sense */
1996-10-13 07:21:13 +04:00
printf("cmd[%d,%d]: ", xs->cmdlen, sz = command_size(*p1));
for (i = 0; i < sz; i++)
1996-10-13 07:21:13 +04:00
printf("%x ", p1[i]);
printf("\nsense: ");
for (i = 0; i < sizeof(xs->sense.scsi_sense); i++)
1996-10-13 07:21:13 +04:00
printf("%x ", p2[i]);
printf("\n");
}
static void
show_request(reqp, qtxt)
SC_REQ *reqp;
char *qtxt;
{
1996-10-13 07:21:13 +04:00
printf("REQ-%s: %d %p[%ld] cmd[0]=%x S=%x M=%x R=%x resid=%d dr_flag=%x %s\n",
qtxt, reqp->targ_id, reqp->xdata_ptr, reqp->xdata_len,
reqp->xcmd.opcode, reqp->status, reqp->message,
reqp->xs->error, reqp->xs->resid, reqp->dr_flag,
reqp->link ? "L":"");
if (reqp->status == SCSCHKC)
show_data_sense(reqp->xs);
}
static char *sig_names[] = {
"PAR", "SEL", "I/O", "C/D", "MSG", "REQ", "BSY", "RST",
"ACK", "ATN", "LBSY", "PMATCH", "IRQ", "EPAR", "DREQ", "EDMA"
};
static void
show_signals(dmstat, idstat)
u_char dmstat, idstat;
{
u_short tmp, mask;
int j, need_pipe;
tmp = idstat | ((dmstat & 3) << 8);
1996-10-13 07:21:13 +04:00
printf("Bus signals (%02x/%02x): ", idstat, dmstat & 3);
for (mask = 1, j = need_pipe = 0; mask <= tmp; mask <<= 1, j++) {
if (tmp & mask)
1996-10-13 07:21:13 +04:00
printf("%s%s", need_pipe++ ? "|" : "", sig_names[j]);
}
1996-10-13 07:21:13 +04:00
printf("\nDma status (%02x): ", dmstat);
for (mask = 4, j = 10, need_pipe = 0; mask <= dmstat; mask <<= 1, j++) {
if (dmstat & mask)
1996-10-13 07:21:13 +04:00
printf("%s%s", need_pipe++ ? "|" : "", sig_names[j]);
}
1996-10-13 07:21:13 +04:00
printf("\n");
}
void
scsi_show()
{
SC_REQ *tmp;
int sps = splhigh();
u_char idstat, dmstat;
#ifdef DBG_PID
int i;
#endif
1996-10-13 07:21:13 +04:00
printf("scsi_show: scsi_main is%s running\n",
main_running ? "" : " not");
for (tmp = issue_q; tmp; tmp = tmp->next)
show_request(tmp, "ISSUED");
for (tmp = discon_q; tmp; tmp = tmp->next)
show_request(tmp, "DISCONNECTED");
if (connected)
show_request(connected, "CONNECTED");
idstat = GET_5380_REG(NCR5380_IDSTAT);
dmstat = GET_5380_REG(NCR5380_DMSTAT);
show_signals(dmstat, idstat);
if (connected)
1996-10-13 07:21:13 +04:00
printf("phase = %d, ", connected->phase);
printf("busy:%x, spl:%04x\n", busy, sps);
#ifdef DBG_PID
for (i=0; i<DBG_PID; i++)
1996-10-13 07:21:13 +04:00
printf("\t%d\t%s\n", i, last_hit[i]);
#endif
splx(sps);
}