NetBSD/sys/ufs/lfs/lfs_vnops.c

909 lines
26 KiB
C
Raw Normal View History

/* $NetBSD: lfs_vnops.c,v 1.61 2002/02/11 02:47:29 perseant Exp $ */
/*-
Various bug-fixes to LFS, to wit: Kernel: * Add runtime quantity lfs_ravail, the number of disk-blocks reserved for writing. Writes to the filesystem first reserve a maximum amount of blocks before their write is allowed to proceed; after the blocks are allocated the reserved total is reduced by a corresponding amount. If the lfs_reserve function cannot immediately reserve the requested number of blocks, the inode is unlocked, and the thread sleeps until the cleaner has made enough space available for the blocks to be reserved. In this way large files can be written to the filesystem (or, smaller files can be written to a nearly-full but thoroughly clean filesystem) and the cleaner can still function properly. * Remove explicit switching on dlfs_minfreeseg from the kernel code; it is now merely a fs-creation parameter used to compute dlfs_avail and dlfs_bfree (and used by fsck_lfs(8) to check their accuracy). Its former role is better assumed by a properly computed dlfs_avail. * Bounds-check inode numbers submitted through lfs_bmapv and lfs_markv. This prevents a panic, but, if the cleaner is feeding the filesystem the wrong data, you are still in a world of hurt. * Cleanup: remove explicit references of DEV_BSIZE in favor of btodb()/dbtob(). lfs_cleanerd: * Make -n mean "send N segments' blocks through a single call to lfs_markv". Previously it had meant "clean N segments though N calls to lfs_markv, before looking again to see if more need to be cleaned". The new behavior gives better packing of direct data on disk with as little metadata as possible, largely alleviating the problem that the cleaner can consume more disk through inefficient use of metadata than it frees by moving dirty data away from clean "holes" to produce entirely clean segments. * Make -b mean "read as many segments as necessary to write N segments of dirty data back to disk", rather than its former meaning of "read as many segments as necessary to free N segments worth of space". The new meaning, combined with the new -n behavior described above, further aids in cleaning storage efficiency as entire segments can be written at once, using as few blocks as possible for segment summaries and inode blocks. * Make the cleaner take note of segments which could not be cleaned due to error, and not attempt to clean them until they are entirely free of dirty blocks. This prevents the case in which a cleanerd running with -n 1 and without -b (formerly the default) would spin trying repeatedly to clean a corrupt segment, while the remaining space filled and deadlocked the filesystem. * Update the lfs_cleanerd manual page to describe all the options, including the changes mentioned here (in particular, the -b and -n flags were previously undocumented). fsck_lfs: * Check, and optionally fix, lfs_avail (to an exact figure) and lfs_bfree (within a margin of error) in pass 5. newfs_lfs: * Reduce the default dlfs_minfreeseg to 1/20 of the total segments. * Add a warning if the sgs disklabel field is 16 (the default for FFS' cpg, but not usually desirable for LFS' sgs: 5--8 is a better range). * Change the calculation of lfs_avail and lfs_bfree, corresponding to the kernel changes mentioned above. mount_lfs: * Add -N and -b options to pass corresponding -n and -b options to lfs_cleanerd. * Default to calling lfs_cleanerd with "-b -n 4". [All of these changes were largely tested in the 1.5 branch, with the idea that they (along with previous un-pulled-up work) could be applied to the branch while it was still in ALPHA2; however my test system has experienced corruption on another filesystem (/dev/console has gone missing :^), and, while I believe this unrelated to the LFS changes, I cannot with good conscience request that the changes be pulled up.]
2000-09-09 08:49:54 +04:00
* Copyright (c) 1999, 2000 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Konrad E. Schroder <perseant@hhhh.org>.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
1998-03-01 05:20:01 +03:00
* Copyright (c) 1986, 1989, 1991, 1993, 1995
* The Regents of the University of California. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the University of
* California, Berkeley and its contributors.
* 4. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
1998-03-01 05:20:01 +03:00
* @(#)lfs_vnops.c 8.13 (Berkeley) 6/10/95
*/
2001-11-08 05:39:06 +03:00
#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: lfs_vnops.c,v 1.61 2002/02/11 02:47:29 perseant Exp $");
2001-11-08 05:39:06 +03:00
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/namei.h>
#include <sys/resourcevar.h>
#include <sys/kernel.h>
#include <sys/file.h>
#include <sys/stat.h>
#include <sys/buf.h>
#include <sys/proc.h>
#include <sys/conf.h>
#include <sys/mount.h>
#include <sys/vnode.h>
#include <sys/malloc.h>
#include <sys/pool.h>
1996-02-10 01:28:45 +03:00
#include <sys/signalvar.h>
#include <miscfs/fifofs/fifo.h>
#include <miscfs/genfs/genfs.h>
#include <miscfs/specfs/specdev.h>
#include <ufs/ufs/inode.h>
#include <ufs/ufs/dir.h>
#include <ufs/ufs/ufsmount.h>
#include <ufs/ufs/ufs_extern.h>
#include <ufs/lfs/lfs.h>
#include <ufs/lfs/lfs_extern.h>
/* Global vfs data structures for lfs. */
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
int (**lfs_vnodeop_p)(void *);
const struct vnodeopv_entry_desc lfs_vnodeop_entries[] = {
{ &vop_default_desc, vn_default_error },
{ &vop_lookup_desc, ufs_lookup }, /* lookup */
{ &vop_create_desc, lfs_create }, /* create */
{ &vop_whiteout_desc, lfs_whiteout }, /* whiteout */
{ &vop_mknod_desc, lfs_mknod }, /* mknod */
{ &vop_open_desc, ufs_open }, /* open */
{ &vop_close_desc, lfs_close }, /* close */
{ &vop_access_desc, ufs_access }, /* access */
{ &vop_getattr_desc, lfs_getattr }, /* getattr */
{ &vop_setattr_desc, lfs_setattr }, /* setattr */
{ &vop_read_desc, lfs_read }, /* read */
{ &vop_write_desc, lfs_write }, /* write */
{ &vop_lease_desc, ufs_lease_check }, /* lease */
{ &vop_ioctl_desc, ufs_ioctl }, /* ioctl */
{ &vop_fcntl_desc, ufs_fcntl }, /* fcntl */
1996-09-07 16:40:22 +04:00
{ &vop_poll_desc, ufs_poll }, /* poll */
1998-03-01 05:20:01 +03:00
{ &vop_revoke_desc, ufs_revoke }, /* revoke */
{ &vop_mmap_desc, ufs_mmap }, /* mmap */
{ &vop_fsync_desc, lfs_fsync }, /* fsync */
{ &vop_seek_desc, ufs_seek }, /* seek */
{ &vop_remove_desc, lfs_remove }, /* remove */
{ &vop_link_desc, lfs_link }, /* link */
{ &vop_rename_desc, lfs_rename }, /* rename */
{ &vop_mkdir_desc, lfs_mkdir }, /* mkdir */
{ &vop_rmdir_desc, lfs_rmdir }, /* rmdir */
{ &vop_symlink_desc, lfs_symlink }, /* symlink */
{ &vop_readdir_desc, ufs_readdir }, /* readdir */
{ &vop_readlink_desc, ufs_readlink }, /* readlink */
{ &vop_abortop_desc, ufs_abortop }, /* abortop */
{ &vop_inactive_desc, lfs_inactive }, /* inactive */
{ &vop_reclaim_desc, lfs_reclaim }, /* reclaim */
{ &vop_lock_desc, ufs_lock }, /* lock */
{ &vop_unlock_desc, ufs_unlock }, /* unlock */
{ &vop_bmap_desc, ufs_bmap }, /* bmap */
{ &vop_strategy_desc, ufs_strategy }, /* strategy */
{ &vop_print_desc, ufs_print }, /* print */
{ &vop_islocked_desc, ufs_islocked }, /* islocked */
{ &vop_pathconf_desc, ufs_pathconf }, /* pathconf */
{ &vop_advlock_desc, ufs_advlock }, /* advlock */
{ &vop_blkatoff_desc, lfs_blkatoff }, /* blkatoff */
{ &vop_valloc_desc, lfs_valloc }, /* valloc */
{ &vop_balloc_desc, lfs_balloc }, /* balloc */
{ &vop_vfree_desc, lfs_vfree }, /* vfree */
{ &vop_truncate_desc, lfs_truncate }, /* truncate */
{ &vop_update_desc, lfs_update }, /* update */
{ &vop_bwrite_desc, lfs_bwrite }, /* bwrite */
{ &vop_getpages_desc, lfs_getpages }, /* getpages */
{ &vop_putpages_desc, lfs_putpages }, /* putpages */
{ NULL, NULL }
};
const struct vnodeopv_desc lfs_vnodeop_opv_desc =
{ &lfs_vnodeop_p, lfs_vnodeop_entries };
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
int (**lfs_specop_p)(void *);
const struct vnodeopv_entry_desc lfs_specop_entries[] = {
{ &vop_default_desc, vn_default_error },
{ &vop_lookup_desc, spec_lookup }, /* lookup */
{ &vop_create_desc, spec_create }, /* create */
{ &vop_mknod_desc, spec_mknod }, /* mknod */
{ &vop_open_desc, spec_open }, /* open */
{ &vop_close_desc, ufsspec_close }, /* close */
{ &vop_access_desc, ufs_access }, /* access */
{ &vop_getattr_desc, lfs_getattr }, /* getattr */
{ &vop_setattr_desc, lfs_setattr }, /* setattr */
{ &vop_read_desc, ufsspec_read }, /* read */
{ &vop_write_desc, ufsspec_write }, /* write */
{ &vop_lease_desc, spec_lease_check }, /* lease */
{ &vop_ioctl_desc, spec_ioctl }, /* ioctl */
{ &vop_fcntl_desc, ufs_fcntl }, /* fcntl */
1996-09-07 16:40:22 +04:00
{ &vop_poll_desc, spec_poll }, /* poll */
1998-03-01 05:20:01 +03:00
{ &vop_revoke_desc, spec_revoke }, /* revoke */
{ &vop_mmap_desc, spec_mmap }, /* mmap */
{ &vop_fsync_desc, spec_fsync }, /* fsync */
{ &vop_seek_desc, spec_seek }, /* seek */
{ &vop_remove_desc, spec_remove }, /* remove */
{ &vop_link_desc, spec_link }, /* link */
{ &vop_rename_desc, spec_rename }, /* rename */
{ &vop_mkdir_desc, spec_mkdir }, /* mkdir */
{ &vop_rmdir_desc, spec_rmdir }, /* rmdir */
{ &vop_symlink_desc, spec_symlink }, /* symlink */
{ &vop_readdir_desc, spec_readdir }, /* readdir */
{ &vop_readlink_desc, spec_readlink }, /* readlink */
{ &vop_abortop_desc, spec_abortop }, /* abortop */
{ &vop_inactive_desc, lfs_inactive }, /* inactive */
{ &vop_reclaim_desc, lfs_reclaim }, /* reclaim */
{ &vop_lock_desc, ufs_lock }, /* lock */
{ &vop_unlock_desc, ufs_unlock }, /* unlock */
{ &vop_bmap_desc, spec_bmap }, /* bmap */
{ &vop_strategy_desc, spec_strategy }, /* strategy */
{ &vop_print_desc, ufs_print }, /* print */
{ &vop_islocked_desc, ufs_islocked }, /* islocked */
{ &vop_pathconf_desc, spec_pathconf }, /* pathconf */
{ &vop_advlock_desc, spec_advlock }, /* advlock */
{ &vop_blkatoff_desc, spec_blkatoff }, /* blkatoff */
{ &vop_valloc_desc, spec_valloc }, /* valloc */
{ &vop_vfree_desc, lfs_vfree }, /* vfree */
{ &vop_truncate_desc, spec_truncate }, /* truncate */
{ &vop_update_desc, lfs_update }, /* update */
{ &vop_bwrite_desc, vn_bwrite }, /* bwrite */
{ &vop_getpages_desc, spec_getpages }, /* getpages */
{ &vop_putpages_desc, spec_putpages }, /* putpages */
{ NULL, NULL }
};
const struct vnodeopv_desc lfs_specop_opv_desc =
{ &lfs_specop_p, lfs_specop_entries };
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
int (**lfs_fifoop_p)(void *);
const struct vnodeopv_entry_desc lfs_fifoop_entries[] = {
{ &vop_default_desc, vn_default_error },
{ &vop_lookup_desc, fifo_lookup }, /* lookup */
{ &vop_create_desc, fifo_create }, /* create */
{ &vop_mknod_desc, fifo_mknod }, /* mknod */
{ &vop_open_desc, fifo_open }, /* open */
{ &vop_close_desc, ufsfifo_close }, /* close */
{ &vop_access_desc, ufs_access }, /* access */
{ &vop_getattr_desc, lfs_getattr }, /* getattr */
{ &vop_setattr_desc, lfs_setattr }, /* setattr */
{ &vop_read_desc, ufsfifo_read }, /* read */
{ &vop_write_desc, ufsfifo_write }, /* write */
{ &vop_lease_desc, fifo_lease_check }, /* lease */
{ &vop_ioctl_desc, fifo_ioctl }, /* ioctl */
{ &vop_fcntl_desc, ufs_fcntl }, /* fcntl */
1996-09-07 16:40:22 +04:00
{ &vop_poll_desc, fifo_poll }, /* poll */
1998-03-01 05:20:01 +03:00
{ &vop_revoke_desc, fifo_revoke }, /* revoke */
{ &vop_mmap_desc, fifo_mmap }, /* mmap */
{ &vop_fsync_desc, fifo_fsync }, /* fsync */
{ &vop_seek_desc, fifo_seek }, /* seek */
{ &vop_remove_desc, fifo_remove }, /* remove */
{ &vop_link_desc, fifo_link }, /* link */
{ &vop_rename_desc, fifo_rename }, /* rename */
{ &vop_mkdir_desc, fifo_mkdir }, /* mkdir */
{ &vop_rmdir_desc, fifo_rmdir }, /* rmdir */
{ &vop_symlink_desc, fifo_symlink }, /* symlink */
{ &vop_readdir_desc, fifo_readdir }, /* readdir */
{ &vop_readlink_desc, fifo_readlink }, /* readlink */
{ &vop_abortop_desc, fifo_abortop }, /* abortop */
{ &vop_inactive_desc, lfs_inactive }, /* inactive */
{ &vop_reclaim_desc, lfs_reclaim }, /* reclaim */
{ &vop_lock_desc, ufs_lock }, /* lock */
{ &vop_unlock_desc, ufs_unlock }, /* unlock */
{ &vop_bmap_desc, fifo_bmap }, /* bmap */
{ &vop_strategy_desc, fifo_strategy }, /* strategy */
{ &vop_print_desc, ufs_print }, /* print */
{ &vop_islocked_desc, ufs_islocked }, /* islocked */
{ &vop_pathconf_desc, fifo_pathconf }, /* pathconf */
{ &vop_advlock_desc, fifo_advlock }, /* advlock */
{ &vop_blkatoff_desc, fifo_blkatoff }, /* blkatoff */
{ &vop_valloc_desc, fifo_valloc }, /* valloc */
{ &vop_vfree_desc, lfs_vfree }, /* vfree */
{ &vop_truncate_desc, fifo_truncate }, /* truncate */
{ &vop_update_desc, lfs_update }, /* update */
{ &vop_bwrite_desc, lfs_bwrite }, /* bwrite */
{ &vop_putpages_desc, fifo_putpages }, /* putpages */
{ NULL, NULL }
};
const struct vnodeopv_desc lfs_fifoop_opv_desc =
{ &lfs_fifoop_p, lfs_fifoop_entries };
/*
* A function version of LFS_ITIMES, for the UFS functions which call ITIMES
*/
void
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_itimes(struct inode *ip, struct timespec *acc, struct timespec *mod, struct timespec *cre)
{
LFS_ITIMES(ip, acc, mod, cre);
}
#define LFS_READWRITE
#include <ufs/ufs/ufs_readwrite.c>
#undef LFS_READWRITE
/*
* Synch an open file.
*/
/* ARGSUSED */
1996-02-10 01:28:45 +03:00
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_fsync(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_fsync_args /* {
struct vnode *a_vp;
struct ucred *a_cred;
int a_flags;
off_t offlo;
off_t offhi;
struct proc *a_p;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
struct vnode *vp = ap->a_vp;
int error;
/* Ignore the trickle syncer */
if (ap->a_flags & FSYNC_LAZY)
return 0;
simple_lock(&vp->v_interlock);
error = VOP_PUTPAGES(vp, ap->a_offlo, ap->a_offhi,
PGO_CLEANIT | PGO_SYNCIO);
if (error) {
return error;
}
return (VOP_UPDATE(vp, NULL, NULL,
(ap->a_flags & FSYNC_WAIT) != 0 ? UPDATE_WAIT : 0));
}
/*
* Take IN_ADIROP off, then call ufs_inactive.
*/
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_inactive(void *v)
{
struct vop_inactive_args /* {
struct vnode *a_vp;
struct proc *a_p;
} */ *ap = v;
struct inode *ip = VTOI(ap->a_vp);
if (ip->i_flag & IN_ADIROP)
--ip->i_lfs->lfs_nadirop;
ip->i_flag &= ~IN_ADIROP;
return ufs_inactive(v);
}
/*
* These macros are used to bracket UFS directory ops, so that we can
* identify all the pages touched during directory ops which need to
* be ordered and flushed atomically, so that they may be recovered.
*/
/*
* XXX KS - Because we have to mark nodes VDIROP in order to prevent
* the cache from reclaiming them while a dirop is in progress, we must
* also manage the number of nodes so marked (otherwise we can run out).
* We do this by setting lfs_dirvcount to the number of marked vnodes; it
* is decremented during segment write, when VDIROP is taken off.
*/
#define SET_DIROP(vp) lfs_set_dirop(vp)
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
static int lfs_set_dirop(struct vnode *);
extern int lfs_dirvcount;
static int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_set_dirop(struct vnode *vp)
{
struct lfs *fs;
int error;
fs = VTOI(vp)->i_lfs;
Various bug-fixes to LFS, to wit: Kernel: * Add runtime quantity lfs_ravail, the number of disk-blocks reserved for writing. Writes to the filesystem first reserve a maximum amount of blocks before their write is allowed to proceed; after the blocks are allocated the reserved total is reduced by a corresponding amount. If the lfs_reserve function cannot immediately reserve the requested number of blocks, the inode is unlocked, and the thread sleeps until the cleaner has made enough space available for the blocks to be reserved. In this way large files can be written to the filesystem (or, smaller files can be written to a nearly-full but thoroughly clean filesystem) and the cleaner can still function properly. * Remove explicit switching on dlfs_minfreeseg from the kernel code; it is now merely a fs-creation parameter used to compute dlfs_avail and dlfs_bfree (and used by fsck_lfs(8) to check their accuracy). Its former role is better assumed by a properly computed dlfs_avail. * Bounds-check inode numbers submitted through lfs_bmapv and lfs_markv. This prevents a panic, but, if the cleaner is feeding the filesystem the wrong data, you are still in a world of hurt. * Cleanup: remove explicit references of DEV_BSIZE in favor of btodb()/dbtob(). lfs_cleanerd: * Make -n mean "send N segments' blocks through a single call to lfs_markv". Previously it had meant "clean N segments though N calls to lfs_markv, before looking again to see if more need to be cleaned". The new behavior gives better packing of direct data on disk with as little metadata as possible, largely alleviating the problem that the cleaner can consume more disk through inefficient use of metadata than it frees by moving dirty data away from clean "holes" to produce entirely clean segments. * Make -b mean "read as many segments as necessary to write N segments of dirty data back to disk", rather than its former meaning of "read as many segments as necessary to free N segments worth of space". The new meaning, combined with the new -n behavior described above, further aids in cleaning storage efficiency as entire segments can be written at once, using as few blocks as possible for segment summaries and inode blocks. * Make the cleaner take note of segments which could not be cleaned due to error, and not attempt to clean them until they are entirely free of dirty blocks. This prevents the case in which a cleanerd running with -n 1 and without -b (formerly the default) would spin trying repeatedly to clean a corrupt segment, while the remaining space filled and deadlocked the filesystem. * Update the lfs_cleanerd manual page to describe all the options, including the changes mentioned here (in particular, the -b and -n flags were previously undocumented). fsck_lfs: * Check, and optionally fix, lfs_avail (to an exact figure) and lfs_bfree (within a margin of error) in pass 5. newfs_lfs: * Reduce the default dlfs_minfreeseg to 1/20 of the total segments. * Add a warning if the sgs disklabel field is 16 (the default for FFS' cpg, but not usually desirable for LFS' sgs: 5--8 is a better range). * Change the calculation of lfs_avail and lfs_bfree, corresponding to the kernel changes mentioned above. mount_lfs: * Add -N and -b options to pass corresponding -n and -b options to lfs_cleanerd. * Default to calling lfs_cleanerd with "-b -n 4". [All of these changes were largely tested in the 1.5 branch, with the idea that they (along with previous un-pulled-up work) could be applied to the branch while it was still in ALPHA2; however my test system has experienced corruption on another filesystem (/dev/console has gone missing :^), and, while I believe this unrelated to the LFS changes, I cannot with good conscience request that the changes be pulled up.]
2000-09-09 08:49:54 +04:00
/*
* We might need one directory block plus supporting indirect blocks,
* plus an inode block and ifile page for the new vnode.
*/
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
if ((error = lfs_reserve(fs, vp, btofsb(fs, (NIADDR + 3) << fs->lfs_bshift))) != 0)
Various bug-fixes to LFS, to wit: Kernel: * Add runtime quantity lfs_ravail, the number of disk-blocks reserved for writing. Writes to the filesystem first reserve a maximum amount of blocks before their write is allowed to proceed; after the blocks are allocated the reserved total is reduced by a corresponding amount. If the lfs_reserve function cannot immediately reserve the requested number of blocks, the inode is unlocked, and the thread sleeps until the cleaner has made enough space available for the blocks to be reserved. In this way large files can be written to the filesystem (or, smaller files can be written to a nearly-full but thoroughly clean filesystem) and the cleaner can still function properly. * Remove explicit switching on dlfs_minfreeseg from the kernel code; it is now merely a fs-creation parameter used to compute dlfs_avail and dlfs_bfree (and used by fsck_lfs(8) to check their accuracy). Its former role is better assumed by a properly computed dlfs_avail. * Bounds-check inode numbers submitted through lfs_bmapv and lfs_markv. This prevents a panic, but, if the cleaner is feeding the filesystem the wrong data, you are still in a world of hurt. * Cleanup: remove explicit references of DEV_BSIZE in favor of btodb()/dbtob(). lfs_cleanerd: * Make -n mean "send N segments' blocks through a single call to lfs_markv". Previously it had meant "clean N segments though N calls to lfs_markv, before looking again to see if more need to be cleaned". The new behavior gives better packing of direct data on disk with as little metadata as possible, largely alleviating the problem that the cleaner can consume more disk through inefficient use of metadata than it frees by moving dirty data away from clean "holes" to produce entirely clean segments. * Make -b mean "read as many segments as necessary to write N segments of dirty data back to disk", rather than its former meaning of "read as many segments as necessary to free N segments worth of space". The new meaning, combined with the new -n behavior described above, further aids in cleaning storage efficiency as entire segments can be written at once, using as few blocks as possible for segment summaries and inode blocks. * Make the cleaner take note of segments which could not be cleaned due to error, and not attempt to clean them until they are entirely free of dirty blocks. This prevents the case in which a cleanerd running with -n 1 and without -b (formerly the default) would spin trying repeatedly to clean a corrupt segment, while the remaining space filled and deadlocked the filesystem. * Update the lfs_cleanerd manual page to describe all the options, including the changes mentioned here (in particular, the -b and -n flags were previously undocumented). fsck_lfs: * Check, and optionally fix, lfs_avail (to an exact figure) and lfs_bfree (within a margin of error) in pass 5. newfs_lfs: * Reduce the default dlfs_minfreeseg to 1/20 of the total segments. * Add a warning if the sgs disklabel field is 16 (the default for FFS' cpg, but not usually desirable for LFS' sgs: 5--8 is a better range). * Change the calculation of lfs_avail and lfs_bfree, corresponding to the kernel changes mentioned above. mount_lfs: * Add -N and -b options to pass corresponding -n and -b options to lfs_cleanerd. * Default to calling lfs_cleanerd with "-b -n 4". [All of these changes were largely tested in the 1.5 branch, with the idea that they (along with previous un-pulled-up work) could be applied to the branch while it was still in ALPHA2; however my test system has experienced corruption on another filesystem (/dev/console has gone missing :^), and, while I believe this unrelated to the LFS changes, I cannot with good conscience request that the changes be pulled up.]
2000-09-09 08:49:54 +04:00
return (error);
if (fs->lfs_dirops == 0)
lfs_check(vp, LFS_UNUSED_LBN, 0);
while (fs->lfs_writer || lfs_dirvcount > LFS_MAXDIROP) {
if (fs->lfs_writer)
tsleep(&fs->lfs_dirops, PRIBIO + 1, "lfs_dirop", 0);
if (lfs_dirvcount > LFS_MAXDIROP && fs->lfs_dirops == 0) {
++fs->lfs_writer;
lfs_flush(fs, 0);
if (--fs->lfs_writer == 0)
wakeup(&fs->lfs_dirops);
}
if (lfs_dirvcount > LFS_MAXDIROP) {
#ifdef DEBUG_LFS
Various bug-fixes to LFS, to wit: Kernel: * Add runtime quantity lfs_ravail, the number of disk-blocks reserved for writing. Writes to the filesystem first reserve a maximum amount of blocks before their write is allowed to proceed; after the blocks are allocated the reserved total is reduced by a corresponding amount. If the lfs_reserve function cannot immediately reserve the requested number of blocks, the inode is unlocked, and the thread sleeps until the cleaner has made enough space available for the blocks to be reserved. In this way large files can be written to the filesystem (or, smaller files can be written to a nearly-full but thoroughly clean filesystem) and the cleaner can still function properly. * Remove explicit switching on dlfs_minfreeseg from the kernel code; it is now merely a fs-creation parameter used to compute dlfs_avail and dlfs_bfree (and used by fsck_lfs(8) to check their accuracy). Its former role is better assumed by a properly computed dlfs_avail. * Bounds-check inode numbers submitted through lfs_bmapv and lfs_markv. This prevents a panic, but, if the cleaner is feeding the filesystem the wrong data, you are still in a world of hurt. * Cleanup: remove explicit references of DEV_BSIZE in favor of btodb()/dbtob(). lfs_cleanerd: * Make -n mean "send N segments' blocks through a single call to lfs_markv". Previously it had meant "clean N segments though N calls to lfs_markv, before looking again to see if more need to be cleaned". The new behavior gives better packing of direct data on disk with as little metadata as possible, largely alleviating the problem that the cleaner can consume more disk through inefficient use of metadata than it frees by moving dirty data away from clean "holes" to produce entirely clean segments. * Make -b mean "read as many segments as necessary to write N segments of dirty data back to disk", rather than its former meaning of "read as many segments as necessary to free N segments worth of space". The new meaning, combined with the new -n behavior described above, further aids in cleaning storage efficiency as entire segments can be written at once, using as few blocks as possible for segment summaries and inode blocks. * Make the cleaner take note of segments which could not be cleaned due to error, and not attempt to clean them until they are entirely free of dirty blocks. This prevents the case in which a cleanerd running with -n 1 and without -b (formerly the default) would spin trying repeatedly to clean a corrupt segment, while the remaining space filled and deadlocked the filesystem. * Update the lfs_cleanerd manual page to describe all the options, including the changes mentioned here (in particular, the -b and -n flags were previously undocumented). fsck_lfs: * Check, and optionally fix, lfs_avail (to an exact figure) and lfs_bfree (within a margin of error) in pass 5. newfs_lfs: * Reduce the default dlfs_minfreeseg to 1/20 of the total segments. * Add a warning if the sgs disklabel field is 16 (the default for FFS' cpg, but not usually desirable for LFS' sgs: 5--8 is a better range). * Change the calculation of lfs_avail and lfs_bfree, corresponding to the kernel changes mentioned above. mount_lfs: * Add -N and -b options to pass corresponding -n and -b options to lfs_cleanerd. * Default to calling lfs_cleanerd with "-b -n 4". [All of these changes were largely tested in the 1.5 branch, with the idea that they (along with previous un-pulled-up work) could be applied to the branch while it was still in ALPHA2; however my test system has experienced corruption on another filesystem (/dev/console has gone missing :^), and, while I believe this unrelated to the LFS changes, I cannot with good conscience request that the changes be pulled up.]
2000-09-09 08:49:54 +04:00
printf("lfs_set_dirop: sleeping with dirops=%d, "
"dirvcount=%d\n", fs->lfs_dirops,
lfs_dirvcount);
#endif
if ((error = tsleep(&lfs_dirvcount, PCATCH|PUSER,
"lfs_maxdirop", 0)) != 0) {
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_reserve(fs, vp, -btofsb(fs, (NIADDR + 3) << fs->lfs_bshift));
return error;
Various bug-fixes to LFS, to wit: Kernel: * Add runtime quantity lfs_ravail, the number of disk-blocks reserved for writing. Writes to the filesystem first reserve a maximum amount of blocks before their write is allowed to proceed; after the blocks are allocated the reserved total is reduced by a corresponding amount. If the lfs_reserve function cannot immediately reserve the requested number of blocks, the inode is unlocked, and the thread sleeps until the cleaner has made enough space available for the blocks to be reserved. In this way large files can be written to the filesystem (or, smaller files can be written to a nearly-full but thoroughly clean filesystem) and the cleaner can still function properly. * Remove explicit switching on dlfs_minfreeseg from the kernel code; it is now merely a fs-creation parameter used to compute dlfs_avail and dlfs_bfree (and used by fsck_lfs(8) to check their accuracy). Its former role is better assumed by a properly computed dlfs_avail. * Bounds-check inode numbers submitted through lfs_bmapv and lfs_markv. This prevents a panic, but, if the cleaner is feeding the filesystem the wrong data, you are still in a world of hurt. * Cleanup: remove explicit references of DEV_BSIZE in favor of btodb()/dbtob(). lfs_cleanerd: * Make -n mean "send N segments' blocks through a single call to lfs_markv". Previously it had meant "clean N segments though N calls to lfs_markv, before looking again to see if more need to be cleaned". The new behavior gives better packing of direct data on disk with as little metadata as possible, largely alleviating the problem that the cleaner can consume more disk through inefficient use of metadata than it frees by moving dirty data away from clean "holes" to produce entirely clean segments. * Make -b mean "read as many segments as necessary to write N segments of dirty data back to disk", rather than its former meaning of "read as many segments as necessary to free N segments worth of space". The new meaning, combined with the new -n behavior described above, further aids in cleaning storage efficiency as entire segments can be written at once, using as few blocks as possible for segment summaries and inode blocks. * Make the cleaner take note of segments which could not be cleaned due to error, and not attempt to clean them until they are entirely free of dirty blocks. This prevents the case in which a cleanerd running with -n 1 and without -b (formerly the default) would spin trying repeatedly to clean a corrupt segment, while the remaining space filled and deadlocked the filesystem. * Update the lfs_cleanerd manual page to describe all the options, including the changes mentioned here (in particular, the -b and -n flags were previously undocumented). fsck_lfs: * Check, and optionally fix, lfs_avail (to an exact figure) and lfs_bfree (within a margin of error) in pass 5. newfs_lfs: * Reduce the default dlfs_minfreeseg to 1/20 of the total segments. * Add a warning if the sgs disklabel field is 16 (the default for FFS' cpg, but not usually desirable for LFS' sgs: 5--8 is a better range). * Change the calculation of lfs_avail and lfs_bfree, corresponding to the kernel changes mentioned above. mount_lfs: * Add -N and -b options to pass corresponding -n and -b options to lfs_cleanerd. * Default to calling lfs_cleanerd with "-b -n 4". [All of these changes were largely tested in the 1.5 branch, with the idea that they (along with previous un-pulled-up work) could be applied to the branch while it was still in ALPHA2; however my test system has experienced corruption on another filesystem (/dev/console has gone missing :^), and, while I believe this unrelated to the LFS changes, I cannot with good conscience request that the changes be pulled up.]
2000-09-09 08:49:54 +04:00
}
}
}
++fs->lfs_dirops;
fs->lfs_doifile = 1;
/* Hold a reference so SET_ENDOP will be happy */
lfs_vref(vp);
return 0;
}
#define SET_ENDOP(fs,vp,str) { \
--(fs)->lfs_dirops; \
if (!(fs)->lfs_dirops) { \
if ((fs)->lfs_nadirop) { \
panic("SET_ENDOP: %s: no dirops but nadirop=%d\n", \
(str), (fs)->lfs_nadirop); \
} \
wakeup(&(fs)->lfs_writer); \
lfs_check((vp),LFS_UNUSED_LBN,0); \
} \
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_reserve((fs), vp, -btofsb((fs), (NIADDR + 3) << (fs)->lfs_bshift)); /* XXX */ \
lfs_vunref(vp); \
}
#define MARK_VNODE(dvp) do { \
if (!((dvp)->v_flag & VDIROP)) { \
(void)lfs_vref(dvp); \
++lfs_dirvcount; \
} \
(dvp)->v_flag |= VDIROP; \
if (!(VTOI(dvp)->i_flag & IN_ADIROP)) { \
++VTOI(dvp)->i_lfs->lfs_nadirop; \
} \
VTOI(dvp)->i_flag |= IN_ADIROP; \
} while (0)
#define UNMARK_VNODE(vp) lfs_unmark_vnode(vp)
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
void lfs_unmark_vnode(struct vnode *vp)
{
struct inode *ip;
ip = VTOI(vp);
if (ip->i_flag & IN_ADIROP)
--ip->i_lfs->lfs_nadirop;
ip->i_flag &= ~IN_ADIROP;
}
1998-03-01 05:20:01 +03:00
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_symlink(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_symlink_args /* {
struct vnode *a_dvp;
struct vnode **a_vpp;
struct componentname *a_cnp;
struct vattr *a_vap;
char *a_target;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vput(ap->a_dvp);
return error;
}
MARK_VNODE(ap->a_dvp);
error = ufs_symlink(ap);
UNMARK_VNODE(ap->a_dvp);
if (*(ap->a_vpp))
UNMARK_VNODE(*(ap->a_vpp));
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"symlink");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_mknod(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_mknod_args /* {
struct vnode *a_dvp;
struct vnode **a_vpp;
struct componentname *a_cnp;
struct vattr *a_vap;
} */ *ap = v;
struct vattr *vap = ap->a_vap;
struct vnode **vpp = ap->a_vpp;
struct inode *ip;
int error;
struct mount *mp;
ino_t ino;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vput(ap->a_dvp);
return error;
}
MARK_VNODE(ap->a_dvp);
error = ufs_makeinode(MAKEIMODE(vap->va_type, vap->va_mode),
ap->a_dvp, vpp, ap->a_cnp);
UNMARK_VNODE(ap->a_dvp);
if (*(ap->a_vpp))
UNMARK_VNODE(*(ap->a_vpp));
/* Either way we're done with the dirop at this point */
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"mknod");
if (error)
return (error);
ip = VTOI(*vpp);
mp = (*vpp)->v_mount;
ino = ip->i_number;
ip->i_flag |= IN_ACCESS | IN_CHANGE | IN_UPDATE;
if (vap->va_rdev != VNOVAL) {
/*
* Want to be able to use this to make badblock
* inodes, so don't truncate the dev number.
*/
#if 0
ip->i_ffs_rdev = ufs_rw32(vap->va_rdev,
UFS_MPNEEDSWAP((*vpp)->v_mount));
#else
ip->i_ffs_rdev = vap->va_rdev;
#endif
}
/*
* Call fsync to write the vnode so that we don't have to deal with
* flushing it when it's marked VDIROP|VXLOCK.
*
* XXX KS - If we can't flush we also can't call vgone(), so must
* return. But, that leaves this vnode in limbo, also not good.
* Can this ever happen (barring hardware failure)?
*/
if ((error = VOP_FSYNC(*vpp, NOCRED, FSYNC_WAIT, 0, 0, curproc)) != 0) {
printf("Couldn't fsync in mknod (ino %d)---what do I do?\n",
VTOI(*vpp)->i_number);
return (error);
}
/*
* Remove vnode so that it will be reloaded by VFS_VGET and
* checked to see if it is an alias of an existing entry in
* the inode cache.
*/
/* Used to be vput, but that causes us to call VOP_INACTIVE twice. */
VOP_UNLOCK(*vpp, 0);
lfs_vunref(*vpp);
(*vpp)->v_type = VNON;
vgone(*vpp);
error = VFS_VGET(mp, ino, vpp);
if (error != 0) {
*vpp = NULL;
return (error);
}
return (0);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_create(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_create_args /* {
struct vnode *a_dvp;
struct vnode **a_vpp;
struct componentname *a_cnp;
struct vattr *a_vap;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vput(ap->a_dvp);
return error;
}
MARK_VNODE(ap->a_dvp);
error = ufs_create(ap);
UNMARK_VNODE(ap->a_dvp);
if (*(ap->a_vpp))
UNMARK_VNODE(*(ap->a_vpp));
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"create");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_whiteout(void *v)
{
struct vop_whiteout_args /* {
struct vnode *a_dvp;
struct componentname *a_cnp;
int a_flags;
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0)
/* XXX no unlock here? */
return error;
MARK_VNODE(ap->a_dvp);
error = ufs_whiteout(ap);
UNMARK_VNODE(ap->a_dvp);
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"whiteout");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_mkdir(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_mkdir_args /* {
struct vnode *a_dvp;
struct vnode **a_vpp;
struct componentname *a_cnp;
struct vattr *a_vap;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vput(ap->a_dvp);
return error;
}
MARK_VNODE(ap->a_dvp);
error = ufs_mkdir(ap);
UNMARK_VNODE(ap->a_dvp);
if (*(ap->a_vpp))
UNMARK_VNODE(*(ap->a_vpp));
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"mkdir");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_remove(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_remove_args /* {
struct vnode *a_dvp;
struct vnode *a_vp;
struct componentname *a_cnp;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
struct vnode *dvp, *vp;
int error;
dvp = ap->a_dvp;
vp = ap->a_vp;
if ((error = SET_DIROP(dvp)) != 0) {
if (dvp == vp)
vrele(vp);
else
vput(vp);
vput(dvp);
return error;
}
MARK_VNODE(dvp);
MARK_VNODE(vp);
error = ufs_remove(ap);
UNMARK_VNODE(dvp);
UNMARK_VNODE(vp);
/*
* If ufs_remove failed, vp doesn't need to be VDIROP any more.
* If it succeeded, we can go ahead and wipe out vp, since
* its loss won't appear on disk until checkpoint, and by then
* dvp will have been written, completing the dirop.
*/
--lfs_dirvcount;
vp->v_flag &= ~VDIROP;
wakeup(&lfs_dirvcount);
vrele(vp);
SET_ENDOP(VTOI(dvp)->i_lfs,dvp,"remove");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_rmdir(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_rmdir_args /* {
struct vnodeop_desc *a_desc;
struct vnode *a_dvp;
struct vnode *a_vp;
struct componentname *a_cnp;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vrele(ap->a_dvp);
if (ap->a_vp->v_mountedhere != NULL)
VOP_UNLOCK(ap->a_dvp, 0);
vput(ap->a_vp);
return error;
}
MARK_VNODE(ap->a_dvp);
MARK_VNODE(ap->a_vp);
error = ufs_rmdir(ap);
UNMARK_VNODE(ap->a_dvp);
UNMARK_VNODE(ap->a_vp);
/*
* If ufs_rmdir failed, vp doesn't need to be VDIROP any more.
* If it succeeded, we can go ahead and wipe out vp, since
* its loss won't appear on disk until checkpoint, and by then
* dvp will have been written, completing the dirop.
*/
--lfs_dirvcount;
ap->a_vp->v_flag &= ~VDIROP;
wakeup(&lfs_dirvcount);
vrele(ap->a_vp);
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"rmdir");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_link(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_link_args /* {
struct vnode *a_dvp;
struct vnode *a_vp;
struct componentname *a_cnp;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
int error;
if ((error = SET_DIROP(ap->a_dvp)) != 0) {
vput(ap->a_dvp);
return error;
}
MARK_VNODE(ap->a_dvp);
error = ufs_link(ap);
UNMARK_VNODE(ap->a_dvp);
SET_ENDOP(VTOI(ap->a_dvp)->i_lfs,ap->a_dvp,"link");
return (error);
}
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_rename(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_rename_args /* {
struct vnode *a_fdvp;
struct vnode *a_fvp;
struct componentname *a_fcnp;
struct vnode *a_tdvp;
struct vnode *a_tvp;
struct componentname *a_tcnp;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
struct vnode *tvp, *fvp, *tdvp, *fdvp;
int error;
struct lfs *fs;
fs = VTOI(ap->a_fdvp)->i_lfs;
tvp = ap->a_tvp;
tdvp = ap->a_tdvp;
fvp = ap->a_fvp;
fdvp = ap->a_fdvp;
/*
* Check for cross-device rename.
* If it is, we don't want to set dirops, just error out.
* (In particular note that MARK_VNODE(tdvp) will DTWT on
* a cross-device rename.)
*
* Copied from ufs_rename.
*/
if ((fvp->v_mount != tdvp->v_mount) ||
(tvp && (fvp->v_mount != tvp->v_mount))) {
error = EXDEV;
goto errout;
}
if ((error = SET_DIROP(fdvp)) != 0)
goto errout;
MARK_VNODE(fdvp);
MARK_VNODE(tdvp);
error = ufs_rename(ap);
UNMARK_VNODE(fdvp);
UNMARK_VNODE(tdvp);
SET_ENDOP(fs,fdvp,"rename");
return (error);
errout:
VOP_ABORTOP(tdvp, ap->a_tcnp); /* XXX, why not in NFS? */
if (tdvp == tvp)
vrele(tdvp);
else
vput(tdvp);
if (tvp)
vput(tvp);
VOP_ABORTOP(fdvp, ap->a_fcnp); /* XXX, why not in NFS? */
vrele(fdvp);
vrele(fvp);
return (error);
}
/* XXX hack to avoid calling ITIMES in getattr */
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_getattr(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_getattr_args /* {
struct vnode *a_vp;
struct vattr *a_vap;
struct ucred *a_cred;
struct proc *a_p;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
2000-03-30 16:41:09 +04:00
struct vnode *vp = ap->a_vp;
struct inode *ip = VTOI(vp);
struct vattr *vap = ap->a_vap;
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
struct lfs *fs = ip->i_lfs;
/*
* Copy from inode table
*/
vap->va_fsid = ip->i_dev;
vap->va_fileid = ip->i_number;
vap->va_mode = ip->i_ffs_mode & ~IFMT;
vap->va_nlink = ip->i_ffs_nlink;
vap->va_uid = ip->i_ffs_uid;
vap->va_gid = ip->i_ffs_gid;
vap->va_rdev = (dev_t)ip->i_ffs_rdev;
a whole bunch of changes to improve performance and robustness under load: - remove special treatment of pager_map mappings in pmaps. this is required now, since I've removed the globals that expose the address range. pager_map now uses pmap_kenter_pa() instead of pmap_enter(), so there's no longer any need to special-case it. - eliminate struct uvm_vnode by moving its fields into struct vnode. - rewrite the pageout path. the pager is now responsible for handling the high-level requests instead of only getting control after a bunch of work has already been done on its behalf. this will allow us to UBCify LFS, which needs tighter control over its pages than other filesystems do. writing a page to disk no longer requires making it read-only, which allows us to write wired pages without causing all kinds of havoc. - use a new PG_PAGEOUT flag to indicate that a page should be freed on behalf of the pagedaemon when it's unlocked. this flag is very similar to PG_RELEASED, but unlike PG_RELEASED, PG_PAGEOUT can be cleared if the pageout fails due to eg. an indirect-block buffer being locked. this allows us to remove the "version" field from struct vm_page, and together with shrinking "loan_count" from 32 bits to 16, struct vm_page is now 4 bytes smaller. - no longer use PG_RELEASED for swap-backed pages. if the page is busy because it's being paged out, we can't release the swap slot to be reallocated until that write is complete, but unlike with vnodes we don't keep a count of in-progress writes so there's no good way to know when the write is done. instead, when we need to free a busy swap-backed page, just sleep until we can get it busy ourselves. - implement a fast-path for extending writes which allows us to avoid zeroing new pages. this substantially reduces cpu usage. - encapsulate the data used by the genfs code in a struct genfs_node, which must be the first element of the filesystem-specific vnode data for filesystems which use genfs_{get,put}pages(). - eliminate many of the UVM pagerops, since they aren't needed anymore now that the pager "put" operation is a higher-level operation. - enhance the genfs code to allow NFS to use the genfs_{get,put}pages instead of a modified copy. - clean up struct vnode by removing all the fields that used to be used by the vfs_cluster.c code (which we don't use anymore with UBC). - remove kmem_object and mb_object since they were useless. instead of allocating pages to these objects, we now just allocate pages with no object. such pages are mapped in the kernel until they are freed, so we can use the mapping to find the page to free it. this allows us to remove splvm() protection in several places. The sum of all these changes improves write throughput on my decstation 5000/200 to within 1% of the rate of NetBSD 1.5 and reduces the elapsed time for "make release" of a NetBSD 1.5 source tree on my 128MB pc to 10% less than a 1.5 kernel took.
2001-09-16 00:36:31 +04:00
vap->va_size = vp->v_size;
vap->va_atime.tv_sec = ip->i_ffs_atime;
vap->va_atime.tv_nsec = ip->i_ffs_atimensec;
vap->va_mtime.tv_sec = ip->i_ffs_mtime;
vap->va_mtime.tv_nsec = ip->i_ffs_mtimensec;
vap->va_ctime.tv_sec = ip->i_ffs_ctime;
vap->va_ctime.tv_nsec = ip->i_ffs_ctimensec;
vap->va_flags = ip->i_ffs_flags;
vap->va_gen = ip->i_ffs_gen;
/* this doesn't belong here */
if (vp->v_type == VBLK)
vap->va_blocksize = BLKDEV_IOSIZE;
else if (vp->v_type == VCHR)
vap->va_blocksize = MAXBSIZE;
else
vap->va_blocksize = vp->v_mount->mnt_stat.f_iosize;
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
vap->va_bytes = fsbtob(fs, (u_quad_t)ip->i_ffs_blocks);
vap->va_type = vp->v_type;
vap->va_filerev = ip->i_modrev;
return (0);
}
/*
* Check to make sure the inode blocks won't choke the buffer
* cache, then call ufs_setattr as usual.
*/
int
lfs_setattr(void *v)
{
struct vop_getattr_args /* {
struct vnode *a_vp;
struct vattr *a_vap;
struct ucred *a_cred;
struct proc *a_p;
} */ *ap = v;
struct vnode *vp = ap->a_vp;
lfs_check(vp, LFS_UNUSED_LBN, 0);
return ufs_setattr(v);
}
/*
* Close called
*
* XXX -- we were using ufs_close, but since it updates the
* times on the inode, we might need to bump the uinodes
* count.
*/
/* ARGSUSED */
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_close(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_close_args /* {
struct vnode *a_vp;
int a_fflag;
struct ucred *a_cred;
struct proc *a_p;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
2000-03-30 16:41:09 +04:00
struct vnode *vp = ap->a_vp;
struct inode *ip = VTOI(vp);
struct timespec ts;
1998-03-01 05:20:01 +03:00
simple_lock(&vp->v_interlock);
if (vp->v_usecount > 1) {
TIMEVAL_TO_TIMESPEC(&time, &ts);
LFS_ITIMES(ip, &ts, &ts, &ts);
}
1998-03-01 05:20:01 +03:00
simple_unlock(&vp->v_interlock);
return (0);
}
/*
1998-03-01 05:20:01 +03:00
* Reclaim an inode so that it can be used for other purposes.
*/
int lfs_no_inactive = 0;
int
Merge the short-lived perseant-lfsv2 branch into the trunk. Kernels and tools understand both v1 and v2 filesystems; newfs_lfs generates v2 by default. Changes for the v2 layout include: - Segments of non-PO2 size and arbitrary block offset, so these can be matched to convenient physical characteristics of the partition (e.g., stripe or track size and offset). - Address by fragment instead of by disk sector, paving the way for non-512-byte-sector devices. In theory fragments can be as large as you like, though in reality they must be smaller than MAXBSIZE in size. - Use serial number and filesystem identifier to ensure that roll-forward doesn't get old data and think it's new. Roll-forward is enabled for v2 filesystems, though not for v1 filesystems by default. - The inode free list is now a tailq, paving the way for undelete (undelete is not yet implemented, but can be without further non-backwards-compatible changes to disk structures). - Inode atime information is kept in the Ifile, instead of on the inode; that is, the inode is never written *just* because atime was changed. Because of this the inodes remain near the file data on the disk, rather than wandering all over as the disk is read repeatedly. This speeds up repeated reads by a small but noticeable amount. Other changes of note include: - The ifile written by newfs_lfs can now be of arbitrary length, it is no longer restricted to a single indirect block. - Fixed an old bug where ctime was changed every time a vnode was created. I need to look more closely to make sure that the times are only updated during write(2) and friends, not after-the-fact during a segment write, and certainly not by the cleaner.
2001-07-14 00:30:18 +04:00
lfs_reclaim(void *v)
1996-02-10 01:28:45 +03:00
{
struct vop_reclaim_args /* {
struct vnode *a_vp;
1998-03-01 05:20:01 +03:00
struct proc *a_p;
1996-02-10 01:28:45 +03:00
} */ *ap = v;
1998-03-01 05:20:01 +03:00
struct vnode *vp = ap->a_vp;
int error;
LFS_CLR_UINO(VTOI(vp), IN_ALLMOD);
1998-03-01 05:20:01 +03:00
if ((error = ufs_reclaim(vp, ap->a_p)))
return (error);
pool_put(&lfs_inode_pool, vp->v_data);
vp->v_data = NULL;
return (0);
}
int
lfs_getpages(void *v)
{
struct vop_getpages_args /* {
struct vnode *a_vp;
voff_t a_offset;
struct vm_page **a_m;
int *a_count;
int a_centeridx;
vm_prot_t a_access_type;
int a_advice;
int a_flags;
} */ *ap = v;
if ((ap->a_access_type & VM_PROT_WRITE) != 0) {
LFS_SET_UINO(VTOI(ap->a_vp), IN_MODIFIED);
}
return genfs_compat_getpages(v);
}
int
lfs_putpages(void *v)
{
int error;
error = genfs_putpages(v);
return error;
}