NetBSD/sys/dev/isa/cs89x0.c

/*	$NetBSD: cs89x0.c,v 1.14 2000/06/28 16:27:52 mrg Exp $	*/

/*
 * Copyright 1997
 * Digital Equipment Corporation. All rights reserved.
 *
 * This software is furnished under license and may be used and
 * copied only in accordance with the following terms and conditions.
 * Subject to these conditions, you may download, copy, install,
 * use, modify and distribute this software in source and/or binary
 * form. No title or ownership is transferred hereby.
 *
 * 1) Any source code used, modified or distributed must reproduce
 *    and retain this copyright notice and list of conditions as
 *    they appear in the source file.
 *
 * 2) No right is granted to use any trade name, trademark, or logo of
 *    Digital Equipment Corporation. Neither the "Digital Equipment
 *    Corporation" name nor any trademark or logo of Digital Equipment
 *    Corporation may be used to endorse or promote products derived
 *    from this software without the prior written permission of
 *    Digital Equipment Corporation.
 *
 * 3) This software is provided "AS-IS" and any express or implied
 *    warranties, including but not limited to, any implied warranties
 *    of merchantability, fitness for a particular purpose, or
 *    non-infringement are disclaimed. In no event shall DIGITAL be
 *    liable for any damages whatsoever, and in particular, DIGITAL
 *    shall not be liable for special, indirect, consequential, or
 *    incidental damages or damages for lost profits, loss of
 *    revenue or loss of use, whether such damages arise in contract,
 *    negligence, tort, under statute, in equity, at law or otherwise,
 *    even if advised of the possibility of such damage.
 */

/*
**++
**  FACILITY
**
**     Device Driver for the Crystal CS8900 ISA Ethernet Controller.
**
**  ABSTRACT
**
**     This module provides standard ethernet access for INET protocols
**     only.
**
**  AUTHORS
**
**     Peter Dettori     SEA - Software Engineering.
**
**  CREATION DATE:
**
**     13-Feb-1997.
**
**  MODIFICATION HISTORY (Digital):
**
**     Revision 1.27  1998/01/20  17:59:40  cgd
**     update for moved headers
**
**     Revision 1.26  1998/01/12  19:29:36  cgd
**     use arm32/isa versions of isadma code.
**
**     Revision 1.25  1997/12/12  01:35:27  cgd
**     convert to use new arp code (from Brini)
**
**     Revision 1.24  1997/12/10  22:31:56  cgd
**     trim some fat (get rid of ability to explicitly supply enet addr, since
**     it was never used and added a bunch of code which really doesn't belong in
**     an enet driver), and clean up slightly.
**
**     Revision 1.23  1997/10/06  16:42:12  cgd
**     copyright notices
**
**     Revision 1.22  1997/06/20  19:38:01  chaiken
**     fixes some smartcard problems
**
**     Revision 1.21  1997/06/10 02:56:20  grohn
**     Added call to ledNetActive
**
**     Revision 1.20  1997/06/05 00:47:06  dettori
**     Changed cs_process_rx_dma to reset and re-initialise the
**     ethernet chip when DMA gets out of sync, or mbufs
**     can't be allocated.
**
**     Revision 1.19  1997/06/03 03:09:58  dettori
**     Turn off sc_txbusy flag when a transmit underrun
**     occurs.
**
**     Revision 1.18  1997/06/02 00:04:35  dettori
**     redefined the transmit table to get around the nfs_timer bug while we are
**     looking into it further.
**
**     Also changed interrupts from EDGE to LEVEL.
**
**     Revision 1.17  1997/05/27 23:31:01  dettori
**     Pulled out changes to DMAMODE defines.
**
**     Revision 1.16  1997/05/23 04:25:16  cgd
**     reformat log so it fits in 80cols
**
**     Revision 1.15  1997/05/23  04:22:18  cgd
**     remove the existing copyright notice (which Peter Dettori indicated
**     was incorrect, copied from an existing NetBSD file only so that the
**     file would have a copyright notice on it, and which he'd intended to
**     replace).  Replace it with a Digital copyright notice, cloned from
**     ess.c.  It's not really correct either (it indicates that the source
**     is Digital confidential!), but is better than nothing and more
**     correct than what was there before.
**
**     Revision 1.14  1997/05/23  04:12:50  cgd
**     use an adaptive transmit start algorithm: start by telling the chip
**     to start transmitting after 381 bytes have been fed to it.  if that
**     gets transmit underruns, ramp down to 1021 bytes then "whole
**     packet."  If successful at a given level for a while, try the next
**     more agressive level.  This code doesn't ever try to start
**     transmitting after 5 bytes have been sent to the NIC, because
**     that underruns rather regularly.  The back-off and ramp-up mechanism
**     could probably be tuned a little bit, but this works well enough to
**     support > 1MB/s transmit rates on a clear ethernet (which is about
**     20-25% better than the driver had previously been getting).
**
**     Revision 1.13  1997/05/22  21:06:54  cgd
**     redo cs_copy_tx_frame() from scratch.  It had a fatal flaw: it was blindly
**     casting from u_int8_t * to u_int16_t * without worrying about alignment
**     issues.  This would cause bogus data to be spit out for mbufs with
**     misaligned data.  For instance, it caused the following bits to appear
**     on the wire:
**     	... etBND 1S2C .SHA(K) R ...
**     	    11112222333344445555
**     which should have appeared as:
**     	... NetBSD 1.2C (SHARK) ...
**     	    11112222333344445555
**     Note the apparent 'rotate' of the bytes in the word, which was due to
**     incorrect unaligned accesses.  This data corruption was the cause of
**     incoming telnet/rlogin hangs.
**
**     Revision 1.12  1997/05/22  01:55:32  cgd
**     reformat log so it fits in 80cols
**
**     Revision 1.11  1997/05/22  01:50:27  cgd
**     * enable input packet address checking in the BPF+IFF_PROMISCUOUS case,
**       so packets aimed at other hosts don't get sent to ether_input().
**     * Add a static const char *rcsid initialized with an RCS Id tag, so that
**       you can easily tell (`strings`) what version of the driver is in your
**       kernel binary.
**     * get rid of ether_cmp().  It was inconsistently used, not necessarily
**       safe, and not really a performance win anyway.  (It was only used when
**       setting up the multicast logical address filter, which is an
**       infrequent event.  It could have been used in the IFF_PROMISCUOUS
**       address check above, but the benefit of it vs. bcmp or memcmp would be
**       inconsequential, there.)  Use bcmp() instead.  Eventually, this should
**       use memcmp(), so that the compiler can optimize it into inline code.
**     * restructure csStartOuput to avoid the following bugs in the case where
**       txWait was being set:
**         * it would accidentally drop the outgoing packet if told to wait
**           but the outgoing packet queue was empty.
**         * it would bpf_mtap() the outgoing packet multiple times (once for
**           each time it was told to wait), and would also recalculate
**           the length of the outgoing packet each time it was told to
**           wait.
**       While there, rename txWait to txLoop, since with the new structure of
**       the code, the latter name makes more sense.
**
**     Revision 1.10  1997/05/19  02:03:20  cgd
**     Set RX_CTL in cs_set_ladr_filt(), rather than cs_initChip().  cs_initChip()
**     is the only caller of cs_set_ladr_filt(), and always calls it, so this
**     ends up being logically the same.  In cs_set_ladr_filt(), if IFF_PROMISC
**     is set, enable promiscuous mode (and set IFF_ALLMULTI), otherwise behave
**     as before.
**
**     Revision 1.9  1997/05/19  01:45:37  cgd
**     create a new function, cs_ether_input(), which does received-packet
**     BPF and ether_input processing.  This code used to be in three places,
**     and centralizing it will make adding IFF_PROMISC support much easier.
**     Also, in cs_copy_tx_frame(), put it some (currently disabled) code to
**     do copies with bus_space_write_region_2().  It's more correct, and
**     potentially more efficient.  That function needs to be gutted (to
**     deal properly with alignment issues, which it currently does wrong),
**     however, and the change doesn't gain much, so there's no point in
**     enabling it now.
**
**     Revision 1.8  1997/05/19  01:17:10  cgd
**     fix a comment re: the setting of the TxConfig register.  Clean up
**     interface counter maintenance (make it use standard idiom).
**
**--
*/

#include "opt_inet.h"

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/mbuf.h>
#include <sys/syslog.h>
#include <sys/socket.h>
#include <sys/device.h>
#include <sys/malloc.h>
#include <sys/ioctl.h>
#include <sys/errno.h>

#include "rnd.h"
#if NRND > 0
#include <sys/rnd.h>
#endif

#include <net/if.h>
#include <net/if_ether.h>
#include <net/if_media.h>
#ifdef INET
#include <netinet/in.h>
#include <netinet/if_inarp.h>
#endif

#include "bpfilter.h"
#if NBPFILTER > 0
#include <net/bpf.h>
#include <net/bpfdesc.h>
#endif

#include <uvm/uvm_extern.h>

#include <machine/bus.h>
#include <machine/intr.h>

#include <dev/isa/isareg.h>
#include <dev/isa/isavar.h>
#include <dev/isa/isadmavar.h>

#include <dev/isa/cs89x0reg.h>
#include <dev/isa/cs89x0var.h>

#ifdef SHARK
#include <arm32/shark/sequoia.h>
#endif

/*
 * MACRO DEFINITIONS
 */
#define CS_OUTPUT_LOOP_MAX 100	/* max times round notorious tx loop */
#define DMA_STATUS_BITS 0x0007	/* bit masks for checking DMA status */
#define DMA_STATUS_OK 0x0004

/*
 * FUNCTION PROTOTYPES
 */
void	cs_get_default_media __P((struct cs_softc *));
int	cs_get_params __P((struct cs_softc *));
int	cs_get_enaddr __P((struct cs_softc *));
int	cs_reset_chip __P((struct cs_softc *));
int	cs_init __P((struct cs_softc *));
void	cs_reset __P((void *));
int	cs_ioctl __P((struct ifnet *, u_long, caddr_t));
void	cs_initChip __P((struct cs_softc *));
void	cs_buffer_event __P((struct cs_softc *, u_int16_t));
void	cs_transmit_event __P((struct cs_softc *, u_int16_t));
void	cs_receive_event __P((struct cs_softc *, u_int16_t));
void	cs_ether_input __P((struct cs_softc *, struct mbuf *));
void	cs_process_receive __P((struct cs_softc *));
void	cs_process_rx_early __P((struct cs_softc *));
void	cs_process_rx_dma __P((struct cs_softc *));
void	cs_start_output __P((struct ifnet *));
void	cs_copy_tx_frame __P((struct cs_softc *, struct mbuf *));
void	cs_set_ladr_filt __P((struct cs_softc *, struct ethercom *));
u_int16_t cs_hash_index __P((char *));
void	cs_counter_event __P((struct cs_softc *, u_int16_t));
void	cs_print_rx_errors __P((struct cs_softc *, u_int16_t));

int	cs_mediachange __P((struct ifnet *));
void	cs_mediastatus __P((struct ifnet *, struct ifmediareq *));

/*
 * GLOBAL DECLARATIONS
 */

/*
 * Xmit-early table.
 *
 * To get better performance, we tell the chip to start packet
 * transmission before the whole packet is copied to the chip.
 * However, this can fail under load.  When it fails, we back off
 * to a safer setting for a little while.
 *
 * txcmd is the value of txcmd used to indicate when to start transmission.
 * better is the next 'better' state in the table.
 * better_count is the number of output packets before transition to the
 *   better state.
 * worse is the next 'worse' state in the table.
 *
 * Transition to the next worse state happens automatically when a
 * transmittion underrun occurs.
 */
struct cs_xmit_early {
	u_int16_t       txcmd;
	int             better;
	int             better_count;
	int             worse;
} cs_xmit_early_table[3] = {
	{ TX_CMD_START_381,	0,	INT_MAX,	1, },
	{ TX_CMD_START_1021,	0,	50000,		2, },
	{ TX_CMD_START_ALL,	1,	5000,		2, },
};

int cs_default_media[] = {
	IFM_ETHER|IFM_10_2,
	IFM_ETHER|IFM_10_5,
	IFM_ETHER|IFM_10_T,
	IFM_ETHER|IFM_10_T|IFM_FDX,
};
int cs_default_nmedia = sizeof(cs_default_media) / sizeof(cs_default_media[0]);

void 
cs_attach(sc, enaddr, media, nmedia, defmedia)
	struct cs_softc *sc;
	u_int8_t *enaddr;
	int *media, nmedia, defmedia;
{
	struct ifnet *ifp = &sc->sc_ethercom.ec_if;
	const char *chipname, *medname;
	u_int16_t reg;
	int i;

	reg = CS_READ_PACKET_PAGE_IO(sc->sc_iot, sc->sc_ioh, PKTPG_PRODUCT_ID);
	sc->sc_prodid = reg & PROD_ID_MASK;
	sc->sc_prodrev = (reg & PROD_REV_MASK) >> 8;

	switch (sc->sc_prodid) {
	case PROD_ID_CS8900:
		chipname = "CS8900";
		break;
	case PROD_ID_CS8920:
		chipname = "CS8920";
		break;
	case PROD_ID_CS8920M:
		chipname = "CS8920M";
		break;
	default:
		panic("cs_attach: impossible");
	}

	/*
	 * the first thing to do is check that the mbuf cluster size is
	 * greater than the MTU for an ethernet frame. The code depends on
	 * this and to port this to a OS where this was not the case would
	 * not be straightforward.
	 */
	if (MCLBYTES < ETHER_MAX_LEN) {
		printf("%s: MCLBYTES too small for Ethernet frame\n",
		    sc->sc_dev.dv_xname);
		return;
	}

	/* Start out in IO mode */
	sc->sc_memorymode = FALSE;

	/* Start out not transmitting */
	sc->sc_txbusy = FALSE;

	/* Set up early transmit threshhold */
	sc->sc_xe_ent = 0;
	sc->sc_xe_togo = cs_xmit_early_table[sc->sc_xe_ent].better_count;

	/* Initialize ifnet structure. */
	bcopy(sc->sc_dev.dv_xname, ifp->if_xname, IFNAMSIZ);
	ifp->if_softc = sc;
	ifp->if_start = cs_start_output;
	ifp->if_ioctl = cs_ioctl;
	ifp->if_watchdog = NULL;	/* no watchdog at this stage */
	ifp->if_flags = IFF_SIMPLEX | IFF_NOTRAILERS |
	    IFF_BROADCAST | IFF_MULTICAST;

	/* Initialize ifmedia structures. */
	ifmedia_init(&sc->sc_media, 0, cs_mediachange, cs_mediastatus);

	if (media != NULL) {
		for (i = 0; i < nmedia; i++)
			ifmedia_add(&sc->sc_media, media[i], 0, NULL);
		ifmedia_set(&sc->sc_media, defmedia);
	} else {
		for (i = 0; i < cs_default_nmedia; i++)
			ifmedia_add(&sc->sc_media, cs_default_media[i],
			    0, NULL);
		cs_get_default_media(sc);
	}

	if ((sc->sc_cfgflags & CFGFLG_NOT_EEPROM) == 0) {
		/* Get parameters from the EEPROM */
		if (cs_get_params(sc) == CS_ERROR) {
			printf("%s: unable to get settings from EEPROM\n",
			    sc->sc_dev.dv_xname);
			return;
		}
	}

	if (enaddr != NULL)
		bcopy(enaddr, sc->sc_enaddr, sizeof(sc->sc_enaddr));
	else if ((sc->sc_cfgflags & CFGFLG_NOT_EEPROM) == 0) {
		/* Get and store the Ethernet address */
		if (cs_get_enaddr(sc) == CS_ERROR) {
			printf("%s: unable to read Ethernet address\n",
			    sc->sc_dev.dv_xname);
			return;
		}
	} else {
		printf("%s: no Ethernet address!\n", sc->sc_dev.dv_xname);
		return;
	}

	switch (IFM_SUBTYPE(sc->sc_media.ifm_cur->ifm_media)) {
	case IFM_10_2:
		medname = "BNC";
		break;
	case IFM_10_5:
		medname = "AUI";
		break;
	case IFM_10_T:
		if (sc->sc_media.ifm_cur->ifm_media & IFM_FDX)
			medname = "UTP <full-duplex>";
		else
			medname = "UTP";
		break;
	default:
		panic("cs_attach: impossible");
	}
	printf("%s: %s rev. %c, address %s, media %s\n", sc->sc_dev.dv_xname,
	    chipname, sc->sc_prodrev + 'A', ether_sprintf(sc->sc_enaddr),
	    medname);

	/*
	 * XXX Driver only supports memory-mode and dma-mode operation for now.
	 * XXX FIXME!!
	 */
	if ((sc->sc_cfgflags & CFGFLG_MEM_MODE) == 0) {
		printf("%s: driver only supports memory mode\n",
		    sc->sc_dev.dv_xname);
		return;
	}

	if (sc->sc_drq == ISACF_DRQ_DEFAULT)
		printf("%s: DMA channel unspecified, not using DMA\n",
		    sc->sc_dev.dv_xname);
	else if (sc->sc_drq < 5 || sc->sc_drq > 7)
		printf("%s: invalid DMA channel, not using DMA\n",
		    sc->sc_dev.dv_xname);
	else {
		bus_size_t maxsize;
		bus_addr_t dma_addr;

		maxsize = isa_dmamaxsize(sc->sc_ic, sc->sc_drq);
		if (maxsize < CS8900_DMASIZE) {
			printf("%s: max DMA size %lu is less than required %d\n",
			    sc->sc_dev.dv_xname, (u_long)maxsize,
			    CS8900_DMASIZE);
			goto after_dma_block;
		}

		if (isa_dmamap_create(sc->sc_ic, sc->sc_drq,
		    CS8900_DMASIZE, BUS_DMA_NOWAIT) != 0) {
			printf("%s: unable to create ISA DMA map\n",
			    sc->sc_dev.dv_xname);
			goto after_dma_block;
		}
		if (isa_dmamem_alloc(sc->sc_ic, sc->sc_drq,
		    CS8900_DMASIZE, &dma_addr, BUS_DMA_NOWAIT) != 0) {
			printf("%s: unable to allocate DMA buffer\n",
			    sc->sc_dev.dv_xname);
			goto after_dma_block;
		}
		if (isa_dmamem_map(sc->sc_ic, sc->sc_drq, dma_addr,
		    CS8900_DMASIZE, &sc->sc_dmabase,
		       BUS_DMA_NOWAIT | BUS_DMA_COHERENT /* XXX */ ) != 0) {
			printf("%s: unable to map DMA buffer\n",
			    sc->sc_dev.dv_xname);
			isa_dmamem_free(sc->sc_ic, sc->sc_drq, dma_addr,
			    CS8900_DMASIZE);
			goto after_dma_block;
		}

		sc->sc_dmasize = CS8900_DMASIZE;
		sc->sc_cfgflags |= CFGFLG_DMA_MODE;
	}
 after_dma_block:

	sc->sc_sh = shutdownhook_establish(cs_reset, sc);
	if (sc->sc_sh == NULL) {
		printf("%s: unable to establish shutdownhook\n",
		    sc->sc_dev.dv_xname);
		return;
	}

	/* Attach the interface. */
	if_attach(ifp);
	ether_ifattach(ifp, sc->sc_enaddr);

#if NBPFILTER > 0
	bpfattach(&ifp->if_bpf, ifp, DLT_EN10MB, sizeof(struct ether_header));
#endif

#if NRND > 0
	rnd_attach_source(&sc->rnd_source, sc->sc_dev.dv_xname,
			  RND_TYPE_NET, 0);
#endif

	/* Reset the chip */
	if (cs_reset_chip(sc) == CS_ERROR)
		printf("%s: reset failed\n", sc->sc_dev.dv_xname);
}

void
cs_get_default_media(sc)
	struct cs_softc *sc;
{
	u_int16_t adp_cfg, xmit_ctl;

	if (cs_verify_eeprom(sc->sc_iot, sc->sc_ioh) == CS_ERROR) {
		printf("%s: cs_get_default_media: EEPROM missing or bad\n",
		    sc->sc_dev.dv_xname);
		goto fakeit;
	}

	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_ADPTR_CFG,
	    &adp_cfg) == CS_ERROR) {
		printf("%s: unable to read adapter config from EEPROM\n",
		    sc->sc_dev.dv_xname);
		goto fakeit;
	}

	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_XMIT_CTL,
	    &xmit_ctl) == CS_ERROR) {
		printf("%s: unable to read transmit control from EEPROM\n",
		    sc->sc_dev.dv_xname);
		goto fakeit;
	}

	switch (adp_cfg & ADPTR_CFG_MEDIA) {
	case ADPTR_CFG_AUI:
		ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_10_5);
		break;
	case ADPTR_CFG_10BASE2:
		ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_10_2);
		break;
	case ADPTR_CFG_10BASET:
	default:
		if (xmit_ctl & XMIT_CTL_FDX)
			ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_10_T|IFM_FDX);
		else
			ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_10_T);
		break;
	}
	return;

 fakeit:
	printf("%s: WARNING: default media setting may be inaccurate\n",
	    sc->sc_dev.dv_xname);
	/* XXX Arbitrary... */
	ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_10_T);
}

int 
cs_get_params(sc)
	struct cs_softc *sc;
{
	u_int16_t isaConfig;
	u_int16_t adapterConfig;

	if (cs_verify_eeprom(sc->sc_iot, sc->sc_ioh) == CS_ERROR) {
		printf("%s: cs_get_params: EEPROM missing or bad\n",
		    sc->sc_dev.dv_xname);
		return (CS_ERROR);
	}

	/* Get ISA configuration from the EEPROM */
	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_ISA_CFG,
	    &isaConfig) == CS_ERROR)
		goto eeprom_bad;

	/* Get adapter configuration from the EEPROM */
	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_ADPTR_CFG,
	    &adapterConfig) == CS_ERROR)
		goto eeprom_bad;

	/* Copy the USE_SA flag */
	if (isaConfig & ISA_CFG_USE_SA)
		sc->sc_cfgflags |= CFGFLG_USE_SA;

	/* Copy the IO Channel Ready flag */
	if (isaConfig & ISA_CFG_IOCHRDY)
		sc->sc_cfgflags |= CFGFLG_IOCHRDY;

	/* Copy the DC/DC Polarity flag */
	if (adapterConfig & ADPTR_CFG_DCDC_POL)
		sc->sc_cfgflags |= CFGFLG_DCDC_POL;

	return (CS_OK);

 eeprom_bad:
	printf("%s: cs_get_params: unable to read from EEPROM\n",
	    sc->sc_dev.dv_xname);
	return (CS_ERROR);
}

int 
cs_get_enaddr(sc)
	struct cs_softc *sc;
{
	u_int16_t *myea;

	if (cs_verify_eeprom(sc->sc_iot, sc->sc_ioh) == CS_ERROR) {
		printf("%s: cs_get_enaddr: EEPROM missing or bad\n",
		    sc->sc_dev.dv_xname);
		return (CS_ERROR);
	}

	myea = (u_int16_t *)sc->sc_enaddr;

	/* Get Ethernet address from the EEPROM */
	/* XXX this will likely lose on a big-endian machine. -- cgd */
	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_IND_ADDR_H,
	    &myea[0]) == CS_ERROR)
		goto eeprom_bad;
	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_IND_ADDR_M,
	    &myea[1]) == CS_ERROR)
		goto eeprom_bad;
	if (cs_read_eeprom(sc->sc_iot, sc->sc_ioh, EEPROM_IND_ADDR_L,
	    &myea[2]) == CS_ERROR)
		goto eeprom_bad;

	return (CS_OK);

 eeprom_bad:
	printf("%s: cs_get_enaddr: unable to read from EEPROM\n",
	    sc->sc_dev.dv_xname);
	return (CS_ERROR);
}

int 
cs_reset_chip(sc)
	struct cs_softc *sc;
{
	int intState;
	int x;

	/* Disable interrupts at the CPU so reset command is atomic */
	intState = splnet();

	/*
	 * We are now resetting the chip
	 * 
	 * A spurious interrupt is generated by the chip when it is reset. This
	 * variable informs the interrupt handler to ignore this interrupt.
	 */
	sc->sc_resetting = TRUE;

	/* Issue a reset command to the chip */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_SELF_CTL, SELF_CTL_RESET);

	/* Re-enable interrupts at the CPU */
	splx(intState);

	/* The chip is always in IO mode after a reset */
	sc->sc_memorymode = FALSE;

	/* If transmission was in progress, it is not now */
	sc->sc_txbusy = FALSE;

	/*
	 * there was a delay(125); here, but it seems uneccesary 125 usec is
	 * 1/8000 of a second, not 1/8 of a second. the data sheet advises
	 * 1/10 of a second here, but the SI_BUSY and INIT_DONE loops below
	 * should be sufficient.
	 */

	/* Transition SBHE to switch chip from 8-bit to 16-bit */
	bus_space_read_1(sc->sc_iot, sc->sc_ioh, PORT_PKTPG_PTR + 0);
	bus_space_read_1(sc->sc_iot, sc->sc_ioh, PORT_PKTPG_PTR + 1);
	bus_space_read_1(sc->sc_iot, sc->sc_ioh, PORT_PKTPG_PTR + 0);
	bus_space_read_1(sc->sc_iot, sc->sc_ioh, PORT_PKTPG_PTR + 1);

	/* Wait until the EEPROM is not busy */
	for (x = 0; x < MAXLOOP; x++) {
		if (!(CS_READ_PACKET_PAGE(sc, PKTPG_SELF_ST) & SELF_ST_SI_BUSY))
			break;
	}

	if (x == MAXLOOP)
		return CS_ERROR;

	/* Wait until initialization is done */
	for (x = 0; x < MAXLOOP; x++) {
		if (CS_READ_PACKET_PAGE(sc, PKTPG_SELF_ST) & SELF_ST_INIT_DONE)
			break;
	}

	if (x == MAXLOOP)
		return CS_ERROR;

	/* Reset is no longer in progress */
	sc->sc_resetting = FALSE;

	return CS_OK;
}

int
cs_verify_eeprom(iot, ioh)
	bus_space_tag_t iot;
	bus_space_handle_t ioh;
{
	u_int16_t self_status;

	/* Verify that the EEPROM is present and OK */
	self_status = CS_READ_PACKET_PAGE_IO(iot, ioh, PKTPG_SELF_ST);
	if (((self_status & SELF_ST_EEP_PRES) &&
	     (self_status & SELF_ST_EEP_OK)) == 0)
		return (CS_ERROR);

	return (CS_OK);
}

int 
cs_read_eeprom(iot, ioh, offset, pValue)
	bus_space_tag_t iot;
	bus_space_handle_t ioh;
	int offset;
	u_int16_t *pValue;
{
	int x;

	/* Ensure that the EEPROM is not busy */
	for (x = 0; x < MAXLOOP; x++) {
		if (!(CS_READ_PACKET_PAGE_IO(iot, ioh, PKTPG_SELF_ST) &
		      SELF_ST_SI_BUSY))
			break;
	}

	if (x == MAXLOOP)
		return (CS_ERROR);

	/* Issue the command to read the offset within the EEPROM */
	CS_WRITE_PACKET_PAGE_IO(iot, ioh, PKTPG_EEPROM_CMD,
	    offset | EEPROM_CMD_READ);

	/* Wait until the command is completed */
	for (x = 0; x < MAXLOOP; x++) {
		if (!(CS_READ_PACKET_PAGE_IO(iot, ioh, PKTPG_SELF_ST) &
		      SELF_ST_SI_BUSY))
			break;
	}

	if (x == MAXLOOP)
		return (CS_ERROR);

	/* Get the EEPROM data from the EEPROM Data register */
	*pValue = CS_READ_PACKET_PAGE_IO(iot, ioh, PKTPG_EEPROM_DATA);

	return (CS_OK);
}

void 
cs_initChip(sc)
	struct cs_softc *sc;
{
	u_int16_t busCtl;
	u_int16_t selfCtl;
	u_int16_t *myea;
	u_int16_t isaId;
	int media = IFM_SUBTYPE(sc->sc_media.ifm_cur->ifm_media);

	/* Disable reception and transmission of frames */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LINE_CTL,
	    CS_READ_PACKET_PAGE(sc, PKTPG_LINE_CTL) &
	    ~LINE_CTL_RX_ON & ~LINE_CTL_TX_ON);

	/* Disable interrupt at the chip */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
	    CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL) & ~BUS_CTL_INT_ENBL);

	/* If IOCHRDY is enabled then clear the bit in the busCtl register */
	busCtl = CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL);
	if (sc->sc_cfgflags & CFGFLG_IOCHRDY) {
		CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
		    busCtl & ~BUS_CTL_IOCHRDY);
	} else {
		CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
		    busCtl | BUS_CTL_IOCHRDY);
	}

	/* Set the Line Control register to match the media type */
	if (media == IFM_10_T)
		CS_WRITE_PACKET_PAGE(sc, PKTPG_LINE_CTL, LINE_CTL_10BASET);
	else
		CS_WRITE_PACKET_PAGE(sc, PKTPG_LINE_CTL, LINE_CTL_AUI_ONLY);

	/*
	 * Set the BSTATUS/HC1 pin to be used as HC1.  HC1 is used to
	 * enable the DC/DC converter
	 */
	selfCtl = SELF_CTL_HC1E;

	/* If the media type is 10Base2 */
	if (media == IFM_10_2) {
		/*
		 * Enable the DC/DC converter if it has a low enable.
		 */
		if ((sc->sc_cfgflags & CFGFLG_DCDC_POL) == 0)
			/*
			 * Set the HCB1 bit, which causes the HC1 pin to go
			 * low.
			 */
			selfCtl |= SELF_CTL_HCB1;
	} else { /* Media type is 10BaseT or AUI */
		/*
		 * Disable the DC/DC converter if it has a high enable.
		 */
		if ((sc->sc_cfgflags & CFGFLG_DCDC_POL) != 0) {
			/*
			 * Set the HCB1 bit, which causes the HC1 pin to go
			 * low.
			 */
			selfCtl |= SELF_CTL_HCB1;
		}
	}
	CS_WRITE_PACKET_PAGE(sc, PKTPG_SELF_CTL, selfCtl);

	/* Enable full-duplex, if appropriate */
	if (sc->sc_media.ifm_cur->ifm_media & IFM_FDX)
		CS_WRITE_PACKET_PAGE(sc, PKTPG_TEST_CTL, TEST_CTL_FDX);

	/* RX_CTL set in cs_set_ladr_filt(), below */

	/* enable all transmission interrupts */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_TX_CFG, TX_CFG_ALL_IE);

	/* Accept all receive interrupts */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG, RX_CFG_ALL_IE);

	/*
	 * Configure Operational Modes
	 * 
	 * I have turned off the BUF_CFG_RX_MISS_IE, to speed things up, this is
	 * a better way to do it because the card has a counter which can be
	 * read to update the RX_MISS counter. This saves many interupts.
	 * 
	 * I have turned on the tx and rx overflow interupts to counter using
	 * the receive miss interrupt. This is a better estimate of errors
	 * and requires lower system overhead.
	 */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_BUF_CFG, BUF_CFG_TX_UNDR_IE |
			  BUF_CFG_RX_DMA_IE);

	if (sc->sc_cfgflags & CFGFLG_DMA_MODE) {
		/*
		 * First we program the DMA controller and ensure the memory
		 * buffer is valid. If it isn't then we just go on without
		 * DMA.
		 */
		if (isa_dmastart(sc->sc_ic, sc->sc_drq, sc->sc_dmabase,
		    sc->sc_dmasize, NULL, DMAMODE_READ | DMAMODE_LOOPDEMAND,
		    BUS_DMA_NOWAIT)) {
			/* XXX XXX XXX */
			panic("%s: unable to start DMA\n", sc->sc_dev.dv_xname);
		}
		sc->sc_dmacur = sc->sc_dmabase;

		/* interrupt when a DMA'd frame is received */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
		    RX_CFG_ALL_IE | RX_CFG_RX_DMA_ONLY);

		/*
		 * set the DMA burst bit so we don't tie up the bus for too
		 * long.
		 */
		if (sc->sc_dmasize == 16384) {
			CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
			    ((CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL) &
			     ~BUS_CTL_DMA_SIZE) | BUS_CTL_DMA_BURST));
		} else { /* use 64K */
			CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
			    CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL) |
			     BUS_CTL_DMA_SIZE | BUS_CTL_DMA_BURST);
		}

		CS_WRITE_PACKET_PAGE(sc, PKTPG_DMA_CHANNEL, sc->sc_drq - 5);
	}

	/* If memory mode is enabled */
	if (sc->sc_cfgflags & CFGFLG_MEM_MODE) {
		/* If external logic is present for address decoding */
		if (CS_READ_PACKET_PAGE(sc, PKTPG_SELF_ST) & SELF_ST_EL_PRES) {
			/*
			 * Program the external logic to decode address bits
			 * SA20-SA23
			 */
			CS_WRITE_PACKET_PAGE(sc, PKTPG_EEPROM_CMD,
			    ((sc->sc_pktpgaddr & 0xffffff) >> 20) |
			    EEPROM_CMD_ELSEL);
		}

		/*
		 * Write the packet page base physical address to the memory
		 * base register.
		 */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_MEM_BASE + 0,
		    sc->sc_pktpgaddr & 0xFFFF);
		CS_WRITE_PACKET_PAGE(sc, PKTPG_MEM_BASE + 2,
		    sc->sc_pktpgaddr >> 16);
		busCtl = BUS_CTL_MEM_MODE;

		/* tell the chip to read the addresses off the SA pins */
		if (sc->sc_cfgflags & CFGFLG_USE_SA) {
			busCtl |= BUS_CTL_USE_SA;
		}
		CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
		    CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL) | busCtl);

		/* We are in memory mode now! */
		sc->sc_memorymode = TRUE;

		/*
		 * wait here (10ms) for the chip to swap over. this is the
		 * maximum time that this could take.
		 */
		delay(10000);

		/* Verify that we can read from the chip */
		isaId = CS_READ_PACKET_PAGE(sc, PKTPG_EISA_NUM);

		/*
		 * As a last minute sanity check before actually using mapped
		 * memory we verify that we can read the isa number from the
		 * chip in memory mode.
		 */
		if (isaId != EISA_NUM_CRYSTAL) {
			printf("%s: failed to enable memory mode\n",
			    sc->sc_dev.dv_xname);
			sc->sc_memorymode = FALSE;
		} else {
			/*
			 * we are in memory mode so if we aren't using DMA,
			 * then program the chip to interrupt early.
			 */
			if ((sc->sc_cfgflags & CFGFLG_DMA_MODE) == 0) {
				CS_WRITE_PACKET_PAGE(sc, PKTPG_BUF_CFG,
				    BUF_CFG_RX_DEST_IE |
				    BUF_CFG_RX_MISS_OVER_IE |
				    BUF_CFG_TX_COL_OVER_IE);
			}
		}

	}

	/* Put Ethernet address into the Individual Address register */
	myea = (u_int16_t *)sc->sc_enaddr;
	CS_WRITE_PACKET_PAGE(sc, PKTPG_IND_ADDR + 0, myea[0]);
	CS_WRITE_PACKET_PAGE(sc, PKTPG_IND_ADDR + 2, myea[1]);
	CS_WRITE_PACKET_PAGE(sc, PKTPG_IND_ADDR + 4, myea[2]);

	/* Set the interrupt level in the chip */
	if (sc->sc_irq == 5) {
		CS_WRITE_PACKET_PAGE(sc, PKTPG_INT_NUM, 3);
	} else {
		CS_WRITE_PACKET_PAGE(sc, PKTPG_INT_NUM, (sc->sc_irq) - 10);
	}

	/* write the multicast mask to the address filter register */
	cs_set_ladr_filt(sc, &sc->sc_ethercom);

	/* Enable reception and transmission of frames */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LINE_CTL,
	    CS_READ_PACKET_PAGE(sc, PKTPG_LINE_CTL) |
	    LINE_CTL_RX_ON | LINE_CTL_TX_ON);

	/* Enable interrupt at the chip */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_BUS_CTL,
	    CS_READ_PACKET_PAGE(sc, PKTPG_BUS_CTL) | BUS_CTL_INT_ENBL);
}

int 
cs_init(sc)
	struct cs_softc *sc;
{
	int intState;
	int error = CS_OK;

	intState = splnet();

	/* Mark the interface as down */
	sc->sc_ethercom.ec_if.if_flags &= ~(IFF_UP | IFF_RUNNING);

#ifdef CS_DEBUG
	/* Enable debugging */
	sc->sc_ethercom.ec_if.if_flags |= IFF_DEBUG;
#endif

	/* Reset the chip */
	if ((error = cs_reset_chip(sc)) == CS_OK) {
		/* Initialize the chip */
		cs_initChip(sc);

		/* Mark the interface as up and running */
		sc->sc_ethercom.ec_if.if_flags |= (IFF_UP | IFF_RUNNING);
		sc->sc_ethercom.ec_if.if_flags &= ~IFF_OACTIVE;
		sc->sc_ethercom.ec_if.if_timer = 0;

		/* Assume we have carrier until we are told otherwise. */
		sc->sc_carrier = 1;
	} else {
		printf("%s: unable to reset chip\n", sc->sc_dev.dv_xname);
	}

	splx(intState);
	return error;
}

void 
cs_set_ladr_filt(sc, ec)
	struct cs_softc *sc;
	struct ethercom *ec;
{
	struct ifnet *ifp = &ec->ec_if;
	struct ether_multi *enm;
	struct ether_multistep step;
	u_int16_t af[4];
	u_int16_t port, mask, index;

	/*
         * Set up multicast address filter by passing all multicast addresses
         * through a crc generator, and then using the high order 6 bits as an
         * index into the 64 bit logical address filter.  The high order bit
         * selects the word, while the rest of the bits select the bit within
         * the word.
         */
	if (ifp->if_flags & IFF_PROMISC) {
		/* accept all valid frames. */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CTL,
		    RX_CTL_PROMISC_A | RX_CTL_RX_OK_A |
		    RX_CTL_IND_A | RX_CTL_BCAST_A | RX_CTL_MCAST_A);
		ifp->if_flags |= IFF_ALLMULTI;
		return;
	}

	/*
	 * accept frames if a. crc valid, b. individual address match c.
	 * broadcast address,and d. multicast addresses matched in the hash
	 * filter
	 */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CTL,
	    RX_CTL_RX_OK_A | RX_CTL_IND_A | RX_CTL_BCAST_A | RX_CTL_MCAST_A);


	/*
	 * start off with all multicast flag clear, set it if we need to
	 * later, otherwise we will leave it.
	 */
	ifp->if_flags &= ~IFF_ALLMULTI;
	af[0] = af[1] = af[2] = af[3] = 0x0000;

	/*
	 * Loop through all the multicast addresses unless we get a range of
	 * addresses, in which case we will just accept all packets.
	 * Justification for this is given in the next comment.
	 */
	ETHER_FIRST_MULTI(step, ec, enm);
	while (enm != NULL) {
		if (bcmp(enm->enm_addrlo, enm->enm_addrhi,
		    sizeof enm->enm_addrlo)) {
			/*
	                 * We must listen to a range of multicast addresses.
	                 * For now, just accept all multicasts, rather than
	                 * trying to set only those filter bits needed to match
	                 * the range.  (At this time, the only use of address
	                 * ranges is for IP multicast routing, for which the
	                 * range is big enough to require all bits set.)
	                 */
			ifp->if_flags |= IFF_ALLMULTI;
			af[0] = af[1] = af[2] = af[3] = 0xffff;
			break;
		} else {
			/*
	                 * we have got an individual address so just set that
	                 * bit.
	                 */
			index = cs_hash_index(enm->enm_addrlo);

			/* Set the bit the Logical address filter. */
			port = (u_int16_t) (index >> 4);
			mask = (u_int16_t) (1 << (index & 0xf));
			af[port] |= mask;

			ETHER_NEXT_MULTI(step, enm);
		}
	}

	/* now program the chip with the addresses */
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LOG_ADDR + 0, af[0]);
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LOG_ADDR + 2, af[1]);
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LOG_ADDR + 4, af[2]);
	CS_WRITE_PACKET_PAGE(sc, PKTPG_LOG_ADDR + 6, af[3]);
	return;
}

u_int16_t
cs_hash_index(addr)
	char *addr;
{
	u_int POLY = 0x04c11db6;
	u_int crc_value = 0xffffffff;
	u_int16_t hash_code = 0;
	int i;
	u_int current_bit;
	char current_byte = *addr;
	u_int cur_crc_high;

	for (i = 0; i < 6; i++) {
		current_byte = *addr;
		addr++;

		for (current_bit = 8; current_bit; current_bit--) {
			cur_crc_high = crc_value >> 31;
			crc_value <<= 1;
			if (cur_crc_high ^ (current_byte & 0x01)) {
				crc_value ^= POLY;
				crc_value |= 0x00000001;
			}
			current_byte >>= 1;
		}
	}

	/*
         * The hash code is the 6 least significant bits of the CRC
         * in the reverse order: CRC[0] = hash[5],CRC[1] = hash[4],etc.
         */
	for (i = 0; i < 6; i++) {
		hash_code = (u_int16_t) ((hash_code << 1) |
		    (u_int16_t) ((crc_value >> i) & 0x00000001));
	}

	return hash_code;
}

void 
cs_reset(arg)
	void *arg;
{
	struct cs_softc *sc = arg;

	/* Mark the interface as down */
	sc->sc_ethercom.ec_if.if_flags &= ~IFF_RUNNING;

	/* Reset the chip */
	cs_reset_chip(sc);
}

int 
cs_ioctl(ifp, cmd, data)
	struct ifnet *ifp;
	u_long cmd;
	caddr_t data;
{
	struct cs_softc *sc = ifp->if_softc;
	struct ifaddr *ifa = (struct ifaddr *) data;
	struct ifreq *ifr = (struct ifreq *) data;
	int state;
	int result;

	state = splnet();

	result = 0;		/* only set if something goes wrong */

	switch (cmd) {
	case SIOCSIFADDR:
		ifp->if_flags |= IFF_UP;

		switch (ifa->ifa_addr->sa_family) {
#ifdef INET
		case AF_INET:
			cs_init(sc);
			arp_ifinit(ifp, ifa);
			break;
#endif
		default:
			cs_init(sc);
			break;
		}
		break;

	case SIOCSIFFLAGS:
		if ((ifp->if_flags & IFF_UP) == 0 &&
		    (ifp->if_flags & IFF_RUNNING) != 0) {
			/*
			 * If interface is marked down and it is running,
			 * then stop it.
			 */
			cs_reset_chip(sc);
			ifp->if_flags &= ~IFF_RUNNING;
		} else if ((ifp->if_flags & IFF_UP) != 0 &&
			   (ifp->if_flags & IFF_RUNNING) == 0) {
			/*
			 * If interface is marked up and it is stopped,
			 * start it.
			 */
			cs_init(sc);
		} else {
			/*
			 * Reset the interface to pick up any changes in
			 * any other flags that affect hardware registers.
			 */
			cs_init(sc);
		}
		break;

	case SIOCADDMULTI:
	case SIOCDELMULTI:
		result = (cmd == SIOCADDMULTI) ?
		    ether_addmulti(ifr, &sc->sc_ethercom) :
		    ether_delmulti(ifr, &sc->sc_ethercom);

		if (result == ENETRESET) {
			/*
	                 * Multicast list has changed; set the hardware filter
	                 * accordingly.
	                 */
			cs_init(sc);
			result = 0;
		}
		break;

	case SIOCGIFMEDIA:
	case SIOCSIFMEDIA:
		result = ifmedia_ioctl(ifp, ifr, &sc->sc_media, cmd);
		break;

	default:
		result = EINVAL;
		break;
	}

	splx(state);

	return result;
}

int
cs_mediachange(ifp)
	struct ifnet *ifp;
{

	/*
	 * Current media is already set up.  Just reset the interface
	 * to let the new value take hold.
	 */
	cs_init((struct cs_softc *)ifp->if_softc);
	return (0);
}

void
cs_mediastatus(ifp, ifmr)
	struct ifnet *ifp;
	struct ifmediareq *ifmr;
{
	struct cs_softc *sc = ifp->if_softc;

	/*
	 * The currently selected media is always the active media.
	 */
	ifmr->ifm_active = sc->sc_media.ifm_cur->ifm_media;

	if (ifp->if_flags & IFF_UP) {
		/* Interface up, status is valid. */
		ifmr->ifm_status = IFM_AVALID |
		    (sc->sc_carrier ? IFM_ACTIVE : 0);
	}
		else ifmr->ifm_status = 0;
}

int 
cs_intr(arg)
	void *arg;
{
	struct cs_softc *sc = arg;
	u_int16_t Event;
#if NRND > 0
	u_int16_t rndEvent;
#endif

	/* Ignore any interrupts that happen while the chip is being reset */
	if (sc->sc_resetting) {
		printf("%s: cs_intr: reset in progress\n",
		    sc->sc_dev.dv_xname);
		return 1;
	}

	/* Read an event from the Interrupt Status Queue */
	Event = CS_READ_PACKET_PAGE(sc, PKTPG_ISQ);

	if ((Event & REG_NUM_MASK) == 0)
		return 0;	/* not ours */

#if NRND > 0
	rndEvent = Event;
#endif

	/* Process all the events in the Interrupt Status Queue */
	while (Event != 0) {
		/* Dispatch to an event handler based on the register number */
		switch (Event & REG_NUM_MASK) {
		case REG_NUM_RX_EVENT:
			cs_receive_event(sc, Event);
			break;
		case REG_NUM_TX_EVENT:
			cs_transmit_event(sc, Event);
			break;
		case REG_NUM_BUF_EVENT:
			cs_buffer_event(sc, Event);
			break;
		case REG_NUM_TX_COL:
		case REG_NUM_RX_MISS:
			cs_counter_event(sc, Event);
			break;
		default:
			printf("%s: unknown interrupt event 0x%x\n",
			    sc->sc_dev.dv_xname, Event);
			break;
		}

		/* Read another event from the Interrupt Status Queue */
		Event = CS_READ_PACKET_PAGE(sc, PKTPG_ISQ);
	}

	/* have handled the interupt */
#if NRND > 0
	rnd_add_uint32(&sc->rnd_source, rndEvent);
#endif
	return 1;
}

void 
cs_counter_event(sc, cntEvent)
	struct cs_softc *sc;
	u_int16_t cntEvent;
{
	struct ifnet *ifp;
	u_int16_t errorCount;

	ifp = &sc->sc_ethercom.ec_if;

	switch (cntEvent & REG_NUM_MASK) {
	case REG_NUM_TX_COL:
		/*
		 * the count should be read before an overflow occurs.
		 */
		errorCount = CS_READ_PACKET_PAGE(sc, PKTPG_TX_COL);
		/*
		 * the tramsit event routine always checks the number of
		 * collisions for any packet so we don't increment any
		 * counters here, as they should already have been
		 * considered.
		 */
		break;
	case REG_NUM_RX_MISS:
		/*
		 * the count should be read before an overflow occurs.
		 */
		errorCount = CS_READ_PACKET_PAGE(sc, PKTPG_RX_MISS);
		/*
		 * Increment the input error count, the first 6bits are the
		 * register id.
		 */
		ifp->if_ierrors += ((errorCount & 0xffC0) >> 6);
		break;
	default:
		/* do nothing */
		break;
	}
}

void 
cs_buffer_event(sc, bufEvent)
	struct cs_softc *sc;
	u_int16_t bufEvent;
{
	struct ifnet *ifp;

	ifp = &sc->sc_ethercom.ec_if;

	/*
	 * multiple events can be in the buffer event register at one time so
	 * a standard switch statement will not suffice, here every event
	 * must be checked.
	 */

	/*
	 * if 128 bits have been rxed by the time we get here, the dest event
	 * will be cleared and 128 event will be set.
	 */
	if ((bufEvent & (BUF_EVENT_RX_DEST | BUF_EVENT_RX_128)) != 0) {
		cs_process_rx_early(sc);
	}

	if (bufEvent & BUF_EVENT_RX_DMA) {
		/* process the receive data */
		cs_process_rx_dma(sc);
	}

	if (bufEvent & BUF_EVENT_TX_UNDR) {
#if 0
		/*
		 * This can happen occasionally, and it's not worth worrying
		 * about.
		 */
		printf("%s: transmit underrun (%d -> %d)\n",
		    sc->sc_dev.dv_xname, sc->sc_xe_ent,
		    cs_xmit_early_table[sc->sc_xe_ent].worse);
#endif
		sc->sc_xe_ent = cs_xmit_early_table[sc->sc_xe_ent].worse;
		sc->sc_xe_togo =
		    cs_xmit_early_table[sc->sc_xe_ent].better_count;

		/* had an underrun, transmit is finished */
		sc->sc_txbusy = FALSE;
	}

	if (bufEvent & BUF_EVENT_SW_INT) {
		printf("%s: software initiated interrupt\n",
		    sc->sc_dev.dv_xname);
	}
}

void 
cs_transmit_event(sc, txEvent)
	struct cs_softc *sc;
	u_int16_t txEvent;
{
	struct ifnet *ifp = &sc->sc_ethercom.ec_if;

	/* If there were any errors transmitting this frame */
	if (txEvent & (TX_EVENT_LOSS_CRS | TX_EVENT_SQE_ERR | TX_EVENT_OUT_WIN |
		       TX_EVENT_JABBER | TX_EVENT_16_COLL)) {
		/* Increment the output error count */
		ifp->if_oerrors++;

		/* Note carrier loss. */
		if (txEvent & TX_EVENT_LOSS_CRS)
			sc->sc_carrier = 0;

		/* If debugging is enabled then log error messages */
		if (ifp->if_flags & IFF_DEBUG) {
			if (txEvent & TX_EVENT_LOSS_CRS) {
				printf("%s: lost carrier\n",
				    sc->sc_dev.dv_xname);
			}
			if (txEvent & TX_EVENT_SQE_ERR) {
				printf("%s: SQE error\n",
				    sc->sc_dev.dv_xname);
			}
			if (txEvent & TX_EVENT_OUT_WIN) {
				printf("%s: out-of-window collision\n",
				    sc->sc_dev.dv_xname);
			}
			if (txEvent & TX_EVENT_JABBER) {
				printf("%s: jabber\n", sc->sc_dev.dv_xname);
			}
			if (txEvent & TX_EVENT_16_COLL) {
				printf("%s: 16 collisions\n",
				    sc->sc_dev.dv_xname);
			}
		}
	}
	else {
		/* Transmission successful, carrier is up. */
		sc->sc_carrier = 1;
#ifdef SHARK
		ledNetActive();
#endif
	}

	/* Add the number of collisions for this frame */
	if (txEvent & TX_EVENT_16_COLL) {
		ifp->if_collisions += 16;
	} else {
		ifp->if_collisions += ((txEvent & TX_EVENT_COLL_MASK) >> 11);
	}

	ifp->if_opackets++;

	/* Transmission is no longer in progress */
	sc->sc_txbusy = FALSE;

	/* If there is more to transmit */
	if (ifp->if_snd.ifq_head != NULL) {
		/* Start the next transmission */
		cs_start_output(ifp);
	}
}

void
cs_print_rx_errors(sc, rxEvent)
	struct cs_softc *sc;
	u_int16_t rxEvent;
{

	if (rxEvent & RX_EVENT_RUNT)
		printf("%s: runt\n", sc->sc_dev.dv_xname);

	if (rxEvent & RX_EVENT_X_DATA)
		printf("%s: extra data\n", sc->sc_dev.dv_xname);

	if (rxEvent & RX_EVENT_CRC_ERR) {
		if (rxEvent & RX_EVENT_DRIBBLE)
			printf("%s: alignment error\n", sc->sc_dev.dv_xname);
		else
			printf("%s: CRC error\n", sc->sc_dev.dv_xname);
	} else {
		if (rxEvent & RX_EVENT_DRIBBLE)
			printf("%s: dribble bits\n", sc->sc_dev.dv_xname);
	}
}

void 
cs_receive_event(sc, rxEvent)
	struct cs_softc *sc;
	u_int16_t rxEvent;
{
	struct ifnet *ifp = &sc->sc_ethercom.ec_if;

	/* If the frame was not received OK */
	if (!(rxEvent & RX_EVENT_RX_OK)) {
		/* Increment the input error count */
		ifp->if_ierrors++;

		/*
		 * If debugging is enabled then log error messages.
		 */
		if (ifp->if_flags & IFF_DEBUG) {
			if (rxEvent != REG_NUM_RX_EVENT) {
				cs_print_rx_errors(sc, rxEvent);

				/*
				 * Must read the length of all received
				 * frames
				 */
				CS_READ_PACKET_PAGE(sc, PKTPG_RX_LENGTH);

				/* Skip the received frame */
				CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
					CS_READ_PACKET_PAGE(sc, PKTPG_RX_CFG) |
						  RX_CFG_SKIP);
			} else {
				printf("%s: implied skip\n",
				    sc->sc_dev.dv_xname);
			}
		}
	} else {
		/*
		 * process the received frame and pass it up to the upper
		 * layers.
		 */
		cs_process_receive(sc);
	}
}

void
cs_ether_input(sc, m)
	struct cs_softc *sc;
	struct mbuf *m;
{
	struct ifnet *ifp = &sc->sc_ethercom.ec_if;
	struct ether_header *eh;

	ifp->if_ipackets++;

	/*
	 * the first thing in the mbuf is the ethernet header. we need to
	 * pass this header to the upper layers as a structure, so cast the
	 * start of the mbuf, and adjust the mbuf to point to the end of the
	 * ethernet header, ie the ethernet packet data.
	 */
	eh = mtod(m, struct ether_header *);

#if NBPFILTER > 0
	/*
	 * Check if there's a BPF listener on this interface.
	 * If so, hand off the raw packet to BPF.
	 */
	if (ifp->if_bpf) {
		bpf_mtap(ifp->if_bpf, m);

		/*
		 * Note that the interface cannot be in promiscuous mode if
		 * there are no BPF listeners.  And if we are in promiscuous
		 * mode, we have to check if this packet is really ours.
		 */
		if ((ifp->if_flags & IFF_PROMISC) &&
		    (eh->ether_dhost[0] & 1) == 0 &&	/* !mcast and !bcast */
		    bcmp(eh->ether_dhost, sc->sc_enaddr,
			 sizeof(eh->ether_dhost)) != 0) {
			m_freem(m);
			return;
		}
	}
#endif

	/* Pass the packet up. */
	(*ifp->if_input)(ifp, m);
}

void 
cs_process_receive(sc)
	struct cs_softc *sc;
{
	struct ifnet *ifp;
	struct mbuf *m;
	int totlen;
	int len;
	volatile u_int16_t *pBuff, *pBuffLimit;
	int pad;
	unsigned int frameOffset;

#ifdef SHARK
	ledNetActive();
#endif

	ifp = &sc->sc_ethercom.ec_if;

	/* Received a packet; carrier is up. */
	sc->sc_carrier = 1;

	/* Initialize the frame offset */
	frameOffset = PKTPG_RX_LENGTH;

	/* Get the length of the received frame */
	totlen = bus_space_read_2(sc->sc_memt, sc->sc_memh, frameOffset);
	frameOffset += 2;

	MGETHDR(m, M_DONTWAIT, MT_DATA);
	if (m == 0) {
		printf("%s: cs_process_receive: unable to allocate mbuf\n",
		    sc->sc_dev.dv_xname);
		ifp->if_ierrors++;
		/*
		 * couldn't allocate an mbuf so things are not good, may as
		 * well drop the packet I think.
		 * 
		 * have already read the length so we should be right to skip
		 * the packet.
		 */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
		    CS_READ_PACKET_PAGE(sc, PKTPG_RX_CFG) | RX_CFG_SKIP);
		return;
	}
	m->m_pkthdr.rcvif = ifp;
	m->m_pkthdr.len = totlen;

	/*
	 * save processing by always using a mbuf cluster, guarenteed to fit
	 * packet, on i386 NetBSD anyway.
	 */
	MCLGET(m, M_DONTWAIT);
	if (m->m_flags & M_EXT) {
		len = MCLBYTES;
	} else {
		/* couldn't allocate an mbuf cluster */
		printf("%s: cs_process_receive: unable to allocate a cluster\n",
		    sc->sc_dev.dv_xname);
		m_freem(m);

		/* skip the received frame */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
		    CS_READ_PACKET_PAGE(sc, PKTPG_RX_CFG) | RX_CFG_SKIP);
		return;
	}

	/* align ip header on word boundary for ipintr */
	pad = ALIGN(sizeof(struct ether_header)) - sizeof(struct ether_header);
	m->m_data += pad;

	m->m_len = len = min(totlen, len);
	pBuff = mtod(m, u_int16_t *);
	pBuffLimit = pBuff + (len + 1) / 2;	/* don't want to go over */

	/* now read the data from the chip */
	while (pBuff < pBuffLimit) {
		*pBuff++ = bus_space_read_2(sc->sc_memt, sc->sc_memh,
		    frameOffset);
		frameOffset += 2;
	}

	cs_ether_input(sc, m);
}

void 
cs_process_rx_dma(sc)
	struct cs_softc *sc;
{
	struct ifnet *ifp;
	u_int16_t num_dma_frames;
	u_int16_t pkt_length;
	u_int16_t status;
	u_int to_copy;
	char *dma_mem_ptr;
	struct mbuf *m;
	u_char *pBuff;
	int pad;

	/* initialise the pointers */
	ifp = &sc->sc_ethercom.ec_if;

	/* Read the number of frames DMAed. */
	num_dma_frames = CS_READ_PACKET_PAGE(sc, PKTPG_DMA_FRAME_COUNT);
	num_dma_frames &= (u_int16_t) (0x0fff);

	/*
	 * Loop till number of DMA frames ready to read is zero. After
	 * reading the frame out of memory we must check if any have been
	 * received while we were processing
	 */
	while (num_dma_frames != 0) {
		dma_mem_ptr = sc->sc_dmacur;

		/*
		 * process all of the dma frames in memory
		 * 
		 * This loop relies on the dma_mem_ptr variable being set to the
		 * next frames start address.
		 */
		for (; num_dma_frames > 0; num_dma_frames--) {

			/*
			 * Get the length and status of the packet. Only the
			 * status is guarenteed to be at dma_mem_ptr, ie need
			 * to check for wraparound before reading the length
			 */
			status = *((unsigned short *) dma_mem_ptr)++;
			if (dma_mem_ptr > (sc->sc_dmabase + sc->sc_dmasize)) {
				dma_mem_ptr = sc->sc_dmabase;
			}
			pkt_length = *((unsigned short *) dma_mem_ptr)++;

			/* Do some sanity checks on the length and status. */
			if ((pkt_length > ETHER_MAX_LEN) ||
			    ((status & DMA_STATUS_BITS) != DMA_STATUS_OK)) {
				/*
				 * the SCO driver kills the adapter in this
				 * situation
				 */
				/*
				 * should increment the error count and reset
				 * the dma operation.
				 */
				printf("%s: cs_process_rx_dma: DMA buffer out of sync about to reset\n",
				    sc->sc_dev.dv_xname);
				ifp->if_ierrors++;

				/* skip the rest of the DMA buffer */
				isa_dmaabort(sc->sc_ic, sc->sc_drq);

				/* now reset the chip and reinitialise */
				cs_init(sc);
				return;
			}
			/* Check the status of the received packet. */
			if (status & RX_EVENT_RX_OK) {
				/* get a new mbuf */
				MGETHDR(m, M_DONTWAIT, MT_DATA);
				if (m == 0) {
					printf("%s: cs_process_rx_dma: unable to allocate mbuf\n",
					    sc->sc_dev.dv_xname);
					ifp->if_ierrors++;
					/*
					 * couldn't allocate an mbuf so
					 * things are not good, may as well
					 * drop all the packets I think.
					 */
					CS_READ_PACKET_PAGE(sc,
					    PKTPG_DMA_FRAME_COUNT);

					/* now reset DMA operation */
					isa_dmaabort(sc->sc_ic, sc->sc_drq);

					/*
					 * now reset the chip and
					 * reinitialise
					 */
					cs_init(sc);
					return;
				}
				/*
				 * save processing by always using a mbuf
				 * cluster, guarenteed to fit packet
				 */
				MCLGET(m, M_DONTWAIT);
				if ((m->m_flags & M_EXT) == 0) {
					/* couldn't allocate an mbuf cluster */
					printf("%s: cs_process_rx_dma: unable to allocate a cluster\n",
					    sc->sc_dev.dv_xname);
					m_freem(m);

					/* skip the frame */
					CS_READ_PACKET_PAGE(sc, PKTPG_DMA_FRAME_COUNT);
					isa_dmaabort(sc->sc_ic, sc->sc_drq);

					/*
					 * now reset the chip and
					 * reinitialise
					 */
					cs_init(sc);
					return;
				}
				m->m_pkthdr.rcvif = ifp;
				m->m_pkthdr.len = pkt_length;
				m->m_len = pkt_length;

				/*
				 * align ip header on word boundary for
				 * ipintr
				 */
				pad = ALIGN(sizeof(struct ether_header)) -
				    sizeof(struct ether_header);
				m->m_data += pad;

				/*
				 * set up the buffer pointer to point to the
				 * data area
				 */
				pBuff = mtod(m, char *);

				/*
				 * Read the frame into free_pktbuf
				 * The buffer is circular buffer, either
				 * 16K or 64K in length.
				 *
				 * need to check where the end of the buffer
				 * is and go back to the start.
				 */
				if ((dma_mem_ptr + pkt_length) <
				    (sc->sc_dmabase + sc->sc_dmasize)) {
					/*
					 * No wrap around. Copy the frame
					 * header
					 */
					bcopy(dma_mem_ptr, pBuff, pkt_length);
					dma_mem_ptr += pkt_length;
				} else {
					to_copy = (u_int)
					    ((sc->sc_dmabase + sc->sc_dmasize) -
					    dma_mem_ptr);

					/* Copy the first half of the frame. */
					bcopy(dma_mem_ptr, pBuff, to_copy);
					pBuff += to_copy;

					/*
		                         * Rest of the frame is to be read
		                         * from the first byte of the DMA
		                         * memory.
		                         */
					/*
					 * Get the number of bytes leftout in
					 * the frame.
					 */
					to_copy = pkt_length - to_copy;

					dma_mem_ptr = sc->sc_dmabase;

					/* Copy rest of the frame. */
					bcopy(dma_mem_ptr, pBuff, to_copy);
					dma_mem_ptr += to_copy;
				}

				cs_ether_input(sc, m);
			}
			/* (status & RX_OK) */ 
			else {
				/* the frame was not received OK */
				/* Increment the input error count */
				ifp->if_ierrors++;

				/*
				 * If debugging is enabled then log error
				 * messages if we got any.
				 */
				if ((ifp->if_flags & IFF_DEBUG) &&
				    status != REG_NUM_RX_EVENT)
					cs_print_rx_errors(sc, status);
			}
			/*
			 * now update the current frame pointer. the
			 * dma_mem_ptr should point to the next packet to be
			 * received, without the alignment considerations.
			 * 
			 * The cs8900 pads all frames to start at the next 32bit
			 * aligned addres. hence we need to pad our offset
			 * pointer.
			 */
			dma_mem_ptr += 3;
			dma_mem_ptr = (char *)
			    ((long) dma_mem_ptr & 0xfffffffc);
			if (dma_mem_ptr < (sc->sc_dmabase + sc->sc_dmasize)) {
				sc->sc_dmacur = dma_mem_ptr;
			} else {
				dma_mem_ptr = sc->sc_dmacur = sc->sc_dmabase;
			}
		} /* for all frames */
		/* Read the number of frames DMAed again. */
		num_dma_frames = CS_READ_PACKET_PAGE(sc, PKTPG_DMA_FRAME_COUNT);
		num_dma_frames &= (u_int16_t) (0x0fff);
	} /* while there are frames left */
}

void 
cs_process_rx_early(sc)
	struct cs_softc *sc;
{
	struct ifnet *ifp;
	struct mbuf *m;
	u_int16_t frameCount, oldFrameCount;
	u_int16_t rxEvent;
	u_int16_t *pBuff;
	int pad;
	unsigned int frameOffset;


	ifp = &sc->sc_ethercom.ec_if;

	/* Initialize the frame offset */
	frameOffset = PKTPG_RX_FRAME;
	frameCount = 0;

	MGETHDR(m, M_DONTWAIT, MT_DATA);
	if (m == 0) {
		printf("%s: cs_process_rx_early: unable to allocate mbuf\n",
		    sc->sc_dev.dv_xname);
		ifp->if_ierrors++;
		/*
		 * couldn't allocate an mbuf so things are not good, may as
		 * well drop the packet I think.
		 * 
		 * have already read the length so we should be right to skip
		 * the packet.
		 */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
		    CS_READ_PACKET_PAGE(sc, PKTPG_RX_CFG) | RX_CFG_SKIP);
		return;
	}
	m->m_pkthdr.rcvif = ifp;
	/*
	 * save processing by always using a mbuf cluster, guarenteed to fit
	 * packet
	 */
	MCLGET(m, M_DONTWAIT);
	if ((m->m_flags & M_EXT) == 0) {
		/* couldn't allocate an mbuf cluster */
		printf("%s: cs_process_rx_early: unable to allocate a cluster\n",
		    sc->sc_dev.dv_xname);
		m_freem(m);
		/* skip the frame */
		CS_WRITE_PACKET_PAGE(sc, PKTPG_RX_CFG,
		    CS_READ_PACKET_PAGE(sc, PKTPG_RX_CFG) | RX_CFG_SKIP);
		return;
	}

	/* align ip header on word boundary for ipintr */
	pad = ALIGN(sizeof(struct ether_header)) - sizeof(struct ether_header);
	m->m_data += pad;

	/* set up the buffer pointer to point to the data area */
	pBuff = mtod(m, u_int16_t *);

	/*
	 * now read the frame byte counter until we have finished reading the
	 * frame
	 */
	oldFrameCount = 0;
	frameCount = bus_space_read_2(sc->sc_memt, sc->sc_memh,
	    PKTPG_FRAME_BYTE_COUNT);
	while ((frameCount != 0) && (frameCount < MCLBYTES)) {
		for (; oldFrameCount < frameCount; oldFrameCount += 2) {
			*pBuff++ = bus_space_read_2(sc->sc_memt, sc->sc_memh,
			    frameOffset);
			frameOffset += 2;
		}

		/* read the new count from the chip */
		frameCount = bus_space_read_2(sc->sc_memt, sc->sc_memh,
		    PKTPG_FRAME_BYTE_COUNT);
	}

	/* update the mbuf counts */
	m->m_len = oldFrameCount;
	m->m_pkthdr.len = oldFrameCount;

	/* now check the Rx Event register */
	rxEvent = CS_READ_PACKET_PAGE(sc, PKTPG_RX_EVENT);

	if ((rxEvent & RX_EVENT_RX_OK) != 0) {
		/*
		 * do an implied skip, it seems to be more reliable than a
		 * forced skip.
		 */
		rxEvent = bus_space_read_2(sc->sc_memt, sc->sc_memh,
		    PKTPG_RX_STATUS);
		rxEvent = bus_space_read_2(sc->sc_memt, sc->sc_memh,
		    PKTPG_RX_LENGTH);

		/*
		 * now read the RX_EVENT register to perform an implied skip.
		 */
		rxEvent = CS_READ_PACKET_PAGE(sc, PKTPG_RX_EVENT);

		cs_ether_input(sc, m);
	} else {
		m_freem(m);
		ifp->if_ierrors++;
	}
}

void 
cs_start_output(ifp)
	struct ifnet *ifp;
{
	struct cs_softc *sc;
	struct mbuf *pMbuf;
	struct mbuf *pMbufChain;
	struct ifqueue *pTxQueue;
	u_int16_t BusStatus;
	u_int16_t Length;
	int txLoop = 0;
	int dropout = 0;

	sc = ifp->if_softc;
	pTxQueue = &sc->sc_ethercom.ec_if.if_snd;

	/* check that the interface is up and running */
	if ((ifp->if_flags & (IFF_RUNNING | IFF_OACTIVE)) != IFF_RUNNING) {
		return;
	}

	/* Don't interrupt a transmission in progress */
	if (sc->sc_txbusy) {
		return;
	}

	/* this loop will only run through once if transmission is successful */
	/*
	 * While there are packets to transmit and a transmit is not in
	 * progress
	 */
	while ((pTxQueue->ifq_head != NULL) && !(sc->sc_txbusy) &&
	    !(dropout)) {
		IF_DEQUEUE(pTxQueue, pMbufChain);

#if NBPFILTER > 0
		/*
	         * If BPF is listening on this interface, let it see the packet
	         * before we commit it to the wire.
	         */
		if (ifp->if_bpf)
			bpf_mtap(ifp->if_bpf, pMbufChain);
#endif

		/* Find the total length of the data to transmit */
		Length = 0;
		for (pMbuf = pMbufChain; pMbuf != NULL; pMbuf = pMbuf->m_next)
			Length += pMbuf->m_len;

		do {
			/*
			 * Request that the transmit be started after all
			 * data has been copied
			 * 
			 * In IO mode must write to the IO port not the packet
			 * page address
			 * 
			 * If this is changed to start transmission after a
			 * small amount of data has been copied you tend to
			 * get packet missed errors i think because the ISA
			 * bus is too slow. Or possibly the copy routine is
			 * not streamlined enough.
			 */
			CS_WRITE_PACKET_PAGE(sc, PKTPG_TX_CMD,
			    cs_xmit_early_table[sc->sc_xe_ent].txcmd);
			CS_WRITE_PACKET_PAGE(sc, PKTPG_TX_LENGTH, Length);

			/*
			 * Adjust early-transmit machinery.
			 */
			if (--sc->sc_xe_togo == 0) {
				sc->sc_xe_ent =
				    cs_xmit_early_table[sc->sc_xe_ent].better;
				sc->sc_xe_togo =
			    cs_xmit_early_table[sc->sc_xe_ent].better_count;
			}
			/*
			 * Read the BusStatus register which indicates
			 * success of the request
			 */
			BusStatus = CS_READ_PACKET_PAGE(sc, PKTPG_BUS_ST);

			/*
			 * If there was an error in the transmit bid free the
			 * mbuf and go on. This is presuming that mbuf is
			 * corrupt.
			 */
			if (BusStatus & BUS_ST_TX_BID_ERR) {
				printf("%s: transmit bid error (too big)",
				    sc->sc_dev.dv_xname);

				/* Discard the bad mbuf chain */
				m_freem(pMbufChain);
				sc->sc_ethercom.ec_if.if_oerrors++;

				/* Loop up to transmit the next chain */
				txLoop = 0;
			} else {
				if (BusStatus & BUS_ST_RDY4TXNOW) {
					/*
					 * The chip is ready for transmission
					 * now
					 */
					/*
					 * Copy the frame to the chip to
					 * start transmission
					 */
					cs_copy_tx_frame(sc, pMbufChain);

					/* Free the mbuf chain */
					m_freem(pMbufChain);

					/* Transmission is now in progress */
					sc->sc_txbusy = TRUE;
					txLoop = 0;
				} else {
					/*
					 * if we get here we want to try
					 * again with the same mbuf, until
					 * the chip lets us transmit.
					 */
					txLoop++;
					if (txLoop > CS_OUTPUT_LOOP_MAX) {
						/* Free the mbuf chain */
						m_freem(pMbufChain);
						/*
						 * Transmission is not in
						 * progress
						 */
						sc->sc_txbusy = FALSE;
						/*
						 * Increment the output error
						 * count
						 */
						ifp->if_oerrors++;
						/*
						 * exit the routine and drop
						 * the packet.
						 */
						txLoop = 0;
						dropout = 1;
					}
				}
			}
		} while (txLoop);
	}
}

void 
cs_copy_tx_frame(sc, m0)
	struct cs_softc *sc;
	struct mbuf *m0;
{
	bus_space_tag_t memt = sc->sc_memt;
	bus_space_handle_t memh = sc->sc_memh;
	struct mbuf *m;
	int len, leftover, frameoff;
	u_int16_t dbuf;
	u_int8_t *p;
#ifdef DIAGNOSTIC
	u_int8_t *lim;
#endif

	/* Initialize frame pointer and data port address */
	frameoff = PKTPG_TX_FRAME;

	/* start out with no leftover data */
	leftover = 0;
	dbuf = 0;

	/* Process the chain of mbufs */
	for (m = m0; m != NULL; m = m->m_next) {
		/*
		 * Process all of the data in a single mbuf.
		 */
		p = mtod(m, u_int8_t *);
		len = m->m_len;
#ifdef DIAGNOSTIC
		lim = p + len;
#endif

		while (len > 0) {
			if (leftover) {
				/*
				 * Data left over (from mbuf or realignment).
				 * Buffer the next byte, and write it and
				 * the leftover data out.
				 */
				dbuf |= *p++ << 8;
				len--;
				bus_space_write_2(memt, memh, frameoff, dbuf);
				frameoff += 2;
				leftover = 0;
			} else if ((long) p & 1) {
				/*
				 * Misaligned data.  Buffer the next byte.
				 */
				dbuf = *p++;
				len--;
				leftover = 1;
			} else {
				/*
				 * Aligned data.  This is the case we like.
				 *
				 * Write-region out as much as we can, then
				 * buffer the remaining byte (if any).
				 */
				leftover = len & 1;
				len &= ~1;
				bus_space_write_region_2(memt, memh, frameoff,
				    (u_int16_t *) p, len >> 1);
				p += len;
				frameoff += len;

				if (leftover)
					dbuf = *p++;
				len = 0;
			}
		}
		if (len < 0)
			panic("cs_copy_tx_frame: negative len");
#ifdef DIAGNOSTIC
		if (p != lim)
			panic("cs_copy_tx_frame: p != lim");
#endif
	}
	if (leftover)
		bus_space_write_2(memt, memh, frameoff, dbuf);
}