NetBSD/sys/dev/ic/dp8390reg.h

551 lines
16 KiB
C
Raw Normal View History

/* $NetBSD: dp8390reg.h,v 1.2 1995/04/12 16:12:42 mycroft Exp $ */
/*
* National Semiconductor DS8390 NIC register definitions.
*
* Copyright (C) 1993, David Greenman. This software may be used, modified,
* copied, distributed, and sold, in both source and binary form provided that
* the above copyright and these terms are retained. Under no circumstances is
* the author responsible for the proper functioning of this software, nor does
* the author assume any responsibility for damages incurred with its use.
*/
/*
* Page 0 register offsets
*/
#define ED_P0_CR 0x00 /* Command Register */
#define ED_P0_CLDA0 0x01 /* Current Local DMA Addr low (read) */
#define ED_P0_PSTART 0x01 /* Page Start register (write) */
#define ED_P0_CLDA1 0x02 /* Current Local DMA Addr high (read) */
#define ED_P0_PSTOP 0x02 /* Page Stop register (write) */
#define ED_P0_BNRY 0x03 /* Boundary Pointer */
#define ED_P0_TSR 0x04 /* Transmit Status Register (read) */
#define ED_P0_TPSR 0x04 /* Transmit Page Start (write) */
#define ED_P0_NCR 0x05 /* Number of Collisions Reg (read) */
#define ED_P0_TBCR0 0x05 /* Transmit Byte count, low (write) */
#define ED_P0_FIFO 0x06 /* FIFO register (read) */
#define ED_P0_TBCR1 0x06 /* Transmit Byte count, high (write) */
#define ED_P0_ISR 0x07 /* Interrupt Status Register */
#define ED_P0_CRDA0 0x08 /* Current Remote DMA Addr low (read) */
#define ED_P0_RSAR0 0x08 /* Remote Start Address low (write) */
#define ED_P0_CRDA1 0x09 /* Current Remote DMA Addr high (read) */
#define ED_P0_RSAR1 0x09 /* Remote Start Address high (write) */
#define ED_P0_RBCR0 0x0a /* Remote Byte Count low (write) */
#define ED_P0_RBCR1 0x0b /* Remote Byte Count high (write) */
#define ED_P0_RSR 0x0c /* Receive Status (read) */
#define ED_P0_RCR 0x0c /* Receive Configuration Reg (write) */
#define ED_P0_CNTR0 0x0d /* frame alignment error counter (read) */
#define ED_P0_TCR 0x0d /* Transmit Configuration Reg (write) */
#define ED_P0_CNTR1 0x0e /* CRC error counter (read) */
#define ED_P0_DCR 0x0e /* Data Configuration Reg (write) */
#define ED_P0_CNTR2 0x0f /* missed packet counter (read) */
#define ED_P0_IMR 0x0f /* Interrupt Mask Register (write) */
/*
* Page 1 register offsets
*/
#define ED_P1_CR 0x00 /* Command Register */
#define ED_P1_PAR0 0x01 /* Physical Address Register 0 */
#define ED_P1_PAR1 0x02 /* Physical Address Register 1 */
#define ED_P1_PAR2 0x03 /* Physical Address Register 2 */
#define ED_P1_PAR3 0x04 /* Physical Address Register 3 */
#define ED_P1_PAR4 0x05 /* Physical Address Register 4 */
#define ED_P1_PAR5 0x06 /* Physical Address Register 5 */
#define ED_P1_CURR 0x07 /* Current RX ring-buffer page */
#define ED_P1_MAR0 0x08 /* Multicast Address Register 0 */
#define ED_P1_MAR1 0x09 /* Multicast Address Register 1 */
#define ED_P1_MAR2 0x0a /* Multicast Address Register 2 */
#define ED_P1_MAR3 0x0b /* Multicast Address Register 3 */
#define ED_P1_MAR4 0x0c /* Multicast Address Register 4 */
#define ED_P1_MAR5 0x0d /* Multicast Address Register 5 */
#define ED_P1_MAR6 0x0e /* Multicast Address Register 6 */
#define ED_P1_MAR7 0x0f /* Multicast Address Register 7 */
/*
* Page 2 register offsets
*/
#define ED_P2_CR 0x00 /* Command Register */
#define ED_P2_PSTART 0x01 /* Page Start (read) */
#define ED_P2_CLDA0 0x01 /* Current Local DMA Addr 0 (write) */
#define ED_P2_PSTOP 0x02 /* Page Stop (read) */
#define ED_P2_CLDA1 0x02 /* Current Local DMA Addr 1 (write) */
#define ED_P2_RNPP 0x03 /* Remote Next Packet Pointer */
#define ED_P2_TPSR 0x04 /* Transmit Page Start (read) */
#define ED_P2_LNPP 0x05 /* Local Next Packet Pointer */
#define ED_P2_ACU 0x06 /* Address Counter Upper */
#define ED_P2_ACL 0x07 /* Address Counter Lower */
#define ED_P2_RCR 0x0c /* Receive Configuration Register (read) */
#define ED_P2_TCR 0x0d /* Transmit Configuration Register (read) */
#define ED_P2_DCR 0x0e /* Data Configuration Register (read) */
#define ED_P2_IMR 0x0f /* Interrupt Mask Register (read) */
/*
* Command Register (CR) definitions
*/
/*
* STP: SToP. Software reset command. Takes the controller offline. No
* packets will be received or transmitted. Any reception or transmission in
* progress will continue to completion before entering reset state. To exit
* this state, the STP bit must reset and the STA bit must be set. The
* software reset has executed only when indicated by the RST bit in the ISR
* being set.
*/
#define ED_CR_STP 0x01
/*
* STA: STArt. This bit is used to activate the NIC after either power-up, or
* when the NIC has been put in reset mode by software command or error.
*/
#define ED_CR_STA 0x02
/*
* TXP: Transmit Packet. This bit must be set to indicate transmission of a
* packet. TXP is internally reset either after the transmission is completed
* or aborted. This bit should be set only after the Transmit Byte Count and
* Transmit Page Start register have been programmed.
*/
#define ED_CR_TXP 0x04
/*
* RD0, RD1, RD2: Remote DMA Command. These three bits control the operation
* of the remote DMA channel. RD2 can be set to abort any remote DMA command
* in progress. The Remote Byte Count registers should be cleared when a
* remote DMA has been aborted. The Remote Start Addresses are not restored
* to the starting address if the remote DMA is aborted.
*
* RD2 RD1 RD0 function
* 0 0 0 not allowed
* 0 0 1 remote read
* 0 1 0 remote write
* 0 1 1 send packet
* 1 X X abort
*/
#define ED_CR_RD0 0x08
#define ED_CR_RD1 0x10
#define ED_CR_RD2 0x20
/*
* PS0, PS1: Page Select. The two bits select which register set or 'page' to
* access.
*
* PS1 PS0 page
* 0 0 0
* 0 1 1
* 1 0 2
* 1 1 reserved
*/
#define ED_CR_PS0 0x40
#define ED_CR_PS1 0x80
/* bit encoded aliases */
#define ED_CR_PAGE_0 0x00 /* (for consistency) */
#define ED_CR_PAGE_1 0x40
#define ED_CR_PAGE_2 0x80
/*
* Interrupt Status Register (ISR) definitions
*/
/*
* PRX: Packet Received. Indicates packet received with no errors.
*/
#define ED_ISR_PRX 0x01
/*
* PTX: Packet Transmitted. Indicates packet transmitted with no errors.
*/
#define ED_ISR_PTX 0x02
/*
* RXE: Receive Error. Indicates that a packet was received with one or more
* the following errors: CRC error, frame alignment error, FIFO overrun,
* missed packet.
*/
#define ED_ISR_RXE 0x04
/*
* TXE: Transmission Error. Indicates that an attempt to transmit a packet
* resulted in one or more of the following errors: excessive collisions, FIFO
* underrun.
*/
#define ED_ISR_TXE 0x08
/*
* OVW: OverWrite. Indicates a receive ring-buffer overrun. Incoming network
* would exceed (has exceeded?) the boundary pointer, resulting in data that
* was previously received and not yet read from the buffer to be overwritten.
*/
#define ED_ISR_OVW 0x10
/*
* CNT: Counter Overflow. Set when the MSB of one or more of the Network Tally
* Counters has been set.
*/
#define ED_ISR_CNT 0x20
/*
* RDC: Remote Data Complete. Indicates that a Remote DMA operation has
* completed.
*/
#define ED_ISR_RDC 0x40
/*
* RST: Reset status. Set when the NIC enters the reset state and cleared when
* a Start Command is issued to the CR. This bit is also set when a receive
* ring-buffer overrun (OverWrite) occurs and is cleared when one or more
* packets have been removed from the ring. This is a read-only bit.
*/
#define ED_ISR_RST 0x80
/*
* Interrupt Mask Register (IMR) definitions
*/
/*
* PRXE: Packet Received interrupt Enable. If set, a received packet will
* cause an interrupt.
*/
#define ED_IMR_PRXE 0x01
/*
* PTXE: Packet Transmit interrupt Enable. If set, an interrupt is generated
* when a packet transmission completes.
*/
#define ED_IMR_PTXE 0x02
/*
* RXEE: Receive Error interrupt Enable. If set, an interrupt will occur
* whenever a packet is received with an error.
*/
#define ED_IMR_RXEE 0x04
/*
* TXEE: Transmit Error interrupt Enable. If set, an interrupt will occur
* whenever a transmission results in an error.
*/
#define ED_IMR_TXEE 0x08
/*
* OVWE: OverWrite error interrupt Enable. If set, an interrupt is generated
* whenever the receive ring-buffer is overrun. i.e. when the boundary pointer
* is exceeded.
*/
#define ED_IMR_OVWE 0x10
/*
* CNTE: Counter overflow interrupt Enable. If set, an interrupt is generated
* whenever the MSB of one or more of the Network Statistics counters has been
* set.
*/
#define ED_IMR_CNTE 0x20
/*
* RDCE: Remote DMA Complete interrupt Enable. If set, an interrupt is
* generated when a remote DMA transfer has completed.
*/
#define ED_IMR_RDCE 0x40
/*
* Bit 7 is unused/reserved.
*/
/*
* Data Configuration Register (DCR) definitions
*/
/*
* WTS: Word Transfer Select. WTS establishes byte or word transfers for both
* remote and local DMA transfers
*/
#define ED_DCR_WTS 0x01
/*
* BOS: Byte Order Select. BOS sets the byte order for the host. Should be 0
* for 80x86, and 1 for 68000 series processors
*/
#define ED_DCR_BOS 0x02
/*
* LAS: Long Address Select. When LAS is 1, the contents of the remote DMA
* registers RSAR0 and RSAR1 are used to provide A16-A31.
*/
#define ED_DCR_LAS 0x04
/*
* LS: Loopback Select. When 0, loopback mode is selected. Bits D1 and D2 of
* the TCR must also be programmed for loopback operation. When 1, normal
* operation is selected.
*/
#define ED_DCR_LS 0x08
/*
* AR: Auto-initialize Remote. When 0, data must be removed from ring-buffer
* under program control. When 1, remote DMA is automatically initiated and
* the boundary pointer is automatically updated.
*/
#define ED_DCR_AR 0x10
/*
* FT0, FT1: Fifo Threshold select.
*
* FT1 FT0 Word-width Byte-width
* 0 0 1 word 2 bytes
* 0 1 2 words 4 bytes
* 1 0 4 words 8 bytes
* 1 1 8 words 12 bytes
*
* During transmission, the FIFO threshold indicates the number of bytes or
* words that the FIFO has filled from the local DMA before BREQ is asserted.
* The transmission threshold is 16 bytes minus the receiver threshold.
*/
#define ED_DCR_FT0 0x20
#define ED_DCR_FT1 0x40
/*
* bit 7 (0x80) is unused/reserved
*/
/*
* Transmit Configuration Register (TCR) definitions
*/
/*
* CRC: Inhibit CRC. If 0, CRC will be appended by the transmitter, if 0, CRC
* is not appended by the transmitter.
*/
#define ED_TCR_CRC 0x01
/*
* LB0, LB1: Loopback control. These two bits set the type of loopback that is
* to be performed.
*
* LB1 LB0 mode
* 0 0 0 - normal operation (DCR_LS = 0)
* 0 1 1 - internal loopback (DCR_LS = 0)
* 1 0 2 - external loopback (DCR_LS = 1)
* 1 1 3 - external loopback (DCR_LS = 0)
*/
#define ED_TCR_LB0 0x02
#define ED_TCR_LB1 0x04
/*
* ATD: Auto Transmit Disable. Clear for normal operation. When set, allows
* another station to disable the NIC's transmitter by transmitting to a
* multicast address hashing to bit 62. Reception of a multicast address
* hashing to bit 63 enables the transmitter.
*/
#define ED_TCR_ATD 0x08
/*
* OFST: Collision Offset enable. This bit when set modifies the backoff
* algorithm to allow prioritization of nodes.
*/
#define ED_TCR_OFST 0x10
/*
* bits 5, 6, and 7 are unused/reserved
*/
/*
* Transmit Status Register (TSR) definitions
*/
/*
* PTX: Packet Transmitted. Indicates successful transmission of packet.
*/
#define ED_TSR_PTX 0x01
/*
* bit 1 (0x02) is unused/reserved
*/
/*
* COL: Transmit Collided. Indicates that the transmission collided at least
* once with another station on the network.
*/
#define ED_TSR_COL 0x04
/*
* ABT: Transmit aborted. Indicates that the transmission was aborted due to
* excessive collisions.
*/
#define ED_TSR_ABT 0x08
/*
* CRS: Carrier Sense Lost. Indicates that carrier was lost during the
* transmission of the packet. (Transmission is not aborted because of a loss
* of carrier).
*/
#define ED_TSR_CRS 0x10
/*
* FU: FIFO Underrun. Indicates that the NIC wasn't able to access bus/
* transmission memory before the FIFO emptied. Transmission of the packet was
* aborted.
*/
#define ED_TSR_FU 0x20
/*
* CDH: CD Heartbeat. Indicates that the collision detection circuitry isn't
* working correctly during a collision heartbeat test.
*/
#define ED_TSR_CDH 0x40
/*
* OWC: Out of Window Collision: Indicates that a collision occurred after a
* slot time (51.2us). The transmission is rescheduled just as in normal
* collisions.
*/
#define ED_TSR_OWC 0x80
/*
* Receiver Configuration Register (RCR) definitions
*/
/*
* SEP: Save Errored Packets. If 0, error packets are discarded. If set to 1,
* packets with CRC and frame errors are not discarded.
*/
#define ED_RCR_SEP 0x01
/*
* AR: Accept Runt packet. If 0, packet with less than 64 byte are discarded.
* If set to 1, packets with less than 64 byte are not discarded.
*/
#define ED_RCR_AR 0x02
/*
* AB: Accept Broadcast. If set, packets sent to the broadcast address will be
* accepted.
*/
#define ED_RCR_AB 0x04
/*
* AM: Accept Multicast. If set, packets sent to a multicast address are
* checked for a match in the hashing array. If clear, multicast packets are
* ignored.
*/
#define ED_RCR_AM 0x08
/*
* PRO: Promiscuous Physical. If set, all packets with a physical addresses
* are accepted. If clear, a physical destination address must match this
* station's address. Note: for full promiscuous mode, RCR_AB and RCR_AM must
* also be set. In addition, the multicast hashing array must be set to all
* 1's so that all multicast addresses are accepted.
*/
#define ED_RCR_PRO 0x10
/*
* MON: Monitor Mode. If set, packets will be checked for good CRC and
* framing, but are not stored in the ring-buffer. If clear, packets are
* stored (normal operation).
*/
#define ED_RCR_MON 0x20
/*
* Bits 6 and 7 are unused/reserved.
*/
/*
* Receiver Status Register (RSR) definitions
*/
/*
* PRX: Packet Received without error.
*/
#define ED_RSR_PRX 0x01
/*
* CRC: CRC error. Indicates that a packet has a CRC error. Also set for
* frame alignment errors.
*/
#define ED_RSR_CRC 0x02
/*
* FAE: Frame Alignment Error. Indicates that the incoming packet did not end
* on a byte boundary and the CRC did not match at the last byte boundary.
*/
#define ED_RSR_FAE 0x04
/*
* FO: FIFO Overrun. Indicates that the FIFO was not serviced (during local
* DMA) causing it to overrun. Reception of the packet is aborted.
*/
#define ED_RSR_FO 0x08
/*
* MPA: Missed Packet. Indicates that the received packet couldn't be stored
* in the ring-buffer because of insufficient buffer space (exceeding the
* boundary pointer), or because the transfer to the ring-buffer was inhibited
* by RCR_MON - monitor mode.
*/
#define ED_RSR_MPA 0x10
/*
* PHY: Physical address. If 0, the packet received was sent to a physical
* address. If 1, the packet was accepted because of a multicast/broadcast
* address match.
*/
#define ED_RSR_PHY 0x20
/*
* DIS: Receiver Disabled. Set to indicate that the receiver has enetered
* monitor mode. Cleared when the receiver exits monitor mode.
*/
#define ED_RSR_DIS 0x40
/*
* DFR: Deferring. Set to indicate a 'jabber' condition. The CRS and COL
* inputs are active, and the transceiver has set the CD line as a result of
* the jabber.
*/
#define ED_RSR_DFR 0x80
/*
* receive ring discriptor
*
* The National Semiconductor DS8390 Network interface controller uses the
* following receive ring headers. The way this works is that the memory on
* the interface card is chopped up into 256 bytes blocks. A contiguous
* portion of those blocks are marked for receive packets by setting start and
* end block #'s in the NIC. For each packet that is put into the receive
* ring, one of these headers (4 bytes each) is tacked onto the front. The
* first byte is a copy of the receiver status register at the time the packet
* was received.
*/
struct ed_ring {
#if BYTE_ORDER == BIG_ENDIAN
u_char next_packet; /* pointer to next packet */
u_char rsr; /* receiver status */
#else
u_char rsr; /* receiver status */
u_char next_packet; /* pointer to next packet */
#endif
u_short count; /* bytes in packet (length + 4) */
};
/*
* Common constants
*/
#define ED_PAGE_SIZE 256 /* Size of RAM pages in bytes */
#define ED_PAGE_MASK 255
#define ED_PAGE_SHIFT 8
#define ED_TXBUF_SIZE 6 /* Size of TX buffer in pages */