NetBSD/dist/ntp/html/gadget.htm

108 lines
5.4 KiB
HTML
Raw Normal View History

2000-03-29 16:38:44 +04:00
<html><head><title>
Gadget Box PPS Level Converter and CHU Modem
</title></head><body><h3>
Gadget Box PPS Level Converter and CHU Modem
</h3>
<p><h4>Introduction</h4>
<p>Many radio clocks used as a primary reference source for NTP servers
produce a pulse-per-second (PPS) signal that can be used to improve
accuracy to a high degree. However, the signals produced are usually
incompatible with the modem interface signals on the serial ports used
to connect the signal to the host. The gadget box consists of a handful
of electronic components assembled in a small aluminum box. It includes
level converters and a optional radio modem designed to decode the radio
timecode signals transmitted by the Canadian time and frequency station
CHU. A complete set of schematics, PCB artwork, drill templates can be
obrtained via the web as the distribution <a href=
"http://www.eecis.udel.edu/~mills/ntp/ntp">gadget.tar.Z</a>, or by
anonymous FTP from ftp.udel.edu in the <TT>pub/ntp</TT> directory.
<p>The gadget box is assembled in a 5&quot;x3&quot;x2&quot; aluminum
minibox containing the level converter and modem circuitry. It includes
two subcircuits. One of these converts a TTL positive edge into a fixed-
width pulse at EIA levels and is for use with a timecode receiver or
oscillator including a TTL PPS output. The other converts the timecode
modulation broadcast by Canadian time/frequency standard station CHU
into a 300-bps serial character stream at EIA levels and is for use with
the <code>tty_clk</code> and <code>chu_tty</code> line disciplines in
the ntp3 distribution.
<p>This archive contains complete construction details for the gadget
box, including schematic, parts list and artwork for a two-sided,
printed-circuit board. All files are in PostScript, with the exception
of this file and an information file, which are in ASCII. The artwork is
in the 1:1 scale and is suitable for direct printing on photographic
resist for each side of the board. While a plated-through-holes process
is most convenient, it is possible to bridge the two sides using
soldered wires where necessary.
<p><h4>Circuit Description</h4>
<p>Following is a brief functional description of the device. See the
schematic diagram gadget.s01 for reference. The audio output of a
shortwave radio tuned to CHU at 3330, 7335 or 14670 kHz is connected to
J2. A level of at least 30 mV peak-peak is required, such as provided by
the recorder output on many receivers. The input level is adjusted by
potentiometer R8 so that the timecode modulation broadcast at 31-39
seconds past the minute reliably lights green LED1, but the signals
broadcast during other seconds of the minute do not.
<p>Opamp U4A provides low-impedance drive for the bridged-tee bandpass
filter U4B. The filter has a bandpass of about 600 Hz at the 6-dB points
and a center frequency of about 2150 Hz. It is designed to avoid
aliasing effects with receivers of relatively wide bandpass
characteristics. The modem itself is implemented by U2 and its
associated circuitry. Resistors R4 and R1 are a 40-dB pad which matches
the filter output to the modem input. U2 is a TTL/EIA level converter
with integral power supply for bipolar signals. The modem output is
available at pin 3 (receive data) of DB25 connector J1.
<p>The TTL PPS signal is connected via J3 to a retriggerable one-shot
U3A, which generates a TTL pulse of width determined by potentiometer
R7. The pulse width is determined by the bit rate of the attached serial
port. In the common case the width is one bit-time, such as 26 us for
38.4 kbps, for example. This appears to the port as a single start bit
of zero followed by eight bits of ones and a stop bit of one. The second
one-shot U3B generates a 200-ms pulse suitable for driving the amber
LED3 as a visual monitor. The output of U3A is converted to EIA levels
by U1 and appears at pin 12 (secondary receive data) of J1.
<p>If only the PPS circuit is required, U2 and U4 can be deleted and the
gadget box powered from the EIA modem-control signal at pin 20 (terminal
ready) of J1, assuming this signal is placed in the on (positive
voltage) condition by the computer program. J1 is wired to keep most
finicky UARTs and terminal-driver programs happy. If the CHU circuit is
required, an external 12-volt AC transformer or 9-12-volt DC supply
connected to J4 is required. Red LED2 indicates power is supplied to the
box.
<p>Files
<p>Following is a list of files included in this archive. All files are
in PostScript, except the <code>README</code> and
<code>gadget.lst</code> files, which are in ASCII. The files
<code>gadget.s01, gadget.s02</code> and <code>gadget.lst</code> were
generated using the Schema schematic-capture program from Omation. The
printed-circuit files <code>*.lpr</code> were generated using Schema-
PCB, also from Omation.
<p>Files
<p><code>README</code> - helpful information
<br><code>gadget.s01</code> - circuit schematic
<br><code>gadget.s02</code> - minibox assembly drawing
<br><code>gadget.lst</code> - net list, pin list, parts list, etc.
<br><code>gen0102.lpr</code> - pcb x-ray diagram
<br><code>art01.lpr</code> - pcb artword side 1
<br><code>art02.lpr</code> - pcb artwork side 2
<br><code>adt0127.lpr</code> - pcb assembly drawing
<br><code>dd0124.lpr</code> - pcb drill drawing
<br><code>sm0228.lpr</code> - pcb solder mask (side 2)
<br><code>sst0126.lpr</code> - pcb silkscreen mask (side 1)
2000-04-22 20:46:49 +04:00
<hr><a href=index.htm>Home</a><address><a
2000-03-29 16:38:44 +04:00
href=mailto:mills@udel.edu> David L. Mills &lt;mills@udel.edu&gt;</a>
</address></a></body></html>